National Instruments NI 9263 Manuel utilisateur

NI-9263

GETTING STARTED GUIDE

NI 9263

4 AO, ±10 V, 16 Bit, 100 kS/s/ch Simultaneous

This document explains how to connect to the NI 9263. In this

document, the NI 9263 with screw terminal and the NI 9263 with

spring terminal are referred to inclusively as the NI 9263.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9263. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9263 only as described in this document.

Caution Do not operate the NI 9263 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

2| ni.com | NI 9263 Getting Started Guide

way. If the product is damaged, return it to NI for

repair.

Hazardous Voltage This icon denotes a warning

advising you to take precautions to avoid electrical

shock with the NI 9263 with screw terminal and the

NI 9263 with spring terminal.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the device, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk voltage or 60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Ensure that devices and circuits connected to

the module are properly insulated from human contact.

Note When module terminals are hazardous voltage

LIVE (>42.4 Vpk/60 VDC), you must ensure that

NI 9263 Getting Started Guide | © National Instruments | 3

devices and circuits connected to the module are

properly insulated from human contact. You must use

the NI 9927 connector backshell kit with the NI 9263

with screw terminal and the NI 9981 connector

backshell kit with the NI 9263 with spring terminal to

ensure that the terminals are not accessible.

Safety Voltages

Connect only voltages that are within the following limits:

Channel-to-channel None

Channel-to-earth ground

Continuous 250 Vrms,

Measurement Category II

Withstand 2,300 Vrms, verified by a 5 s

dielectric withstand test

Division 2 and Zone 2

hazardous locations

applications

(Channel-to-earth ground)

60 VDC,

Measurement Category I

4| ni.com | NI 9263 Getting Started Guide

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Caution Do not connect the NI 9263 to signals or use

for measurements within Measurement Categories II,

III, or IV.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are not

intended for direct connection to the MAINS building

installations of Measurement Categories CAT II,

CAT III, or CAT IV.

Measurement Category II is for measurements performed on

circuits directly connected to the electrical distribution system.

This category refers to local-level electrical distribution, such as

that provided by a standard wall outlet, for example, 115 V for

U.S. or 230 V for Europe.

NI 9263 Getting Started Guide | © National Instruments | 5

Caution Do not connect the NI 9263 to signals or use

for measurements within Measurement Categories III

or IV.

Safety Guidelines for Hazardous Locations

The NI 9263 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9263 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

6| ni.com | NI 9263 Getting Started Guide

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9263 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 07 ATEX 0626664X and is

IECEx UL 14.0089X certified. Each NI 9263 is marked II 3G

and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9263

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

NI 9263 Getting Started Guide | © National Instruments | 7

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product

documentation.

8| ni.com | NI 9263 Getting Started Guide

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance

is attained.

NI 9263 Getting Started Guide | © National Instruments | 9

Autres manuels pour NI 9263

Autres manuels National Instruments Système d'E/S

National Instruments

National Instruments NI 9211E Manuel utilisateur

National Instruments

National Instruments NI 9411 Manuel utilisateur

National Instruments

National Instruments NI-9230 Manuel utilisateur

National Instruments

National Instruments NI USB-6008 Manuel utilisateur

National Instruments

National Instruments 7831R Manuel utilisateur

National Instruments

National Instruments PXIe-4340 Manuel

National Instruments

National Instruments 9237 Manuel

National Instruments

National Instruments FieldPoint FP-DI-330 Manuel utilisateur

National Instruments

National Instruments NI-5761 Manuel utilisateur

National Instruments

National Instruments PXI-6040E Manuel utilisateur

National Instruments

National Instruments REM-11154 Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-DO-410 Manuel utilisateur

National Instruments

National Instruments NI-9224 Manuel utilisateur

National Instruments

National Instruments NI PXI-7831R Manuel utilisateur

National Instruments

National Instruments USB-6001 Manuel utilisateur

National Instruments

National Instruments PC-DIO-96/PnP Manuel utilisateur

National Instruments

National Instruments 9361 Manuel utilisateur

National Instruments

National Instruments PXIe-5164 Manuel utilisateur

National Instruments

National Instruments 9754 Manuel utilisateur

National Instruments

National Instruments USB-7855 Manuel utilisateur

National Instruments

National Instruments NI 9205 Manuel utilisateur

National Instruments

National Instruments NI USB-7855R Manuel utilisateur

National Instruments

National Instruments 9262 Manuel utilisateur

National Instruments

National Instruments NI VISION PCI-8254R Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur