National Instruments 9225E Manuel utilisateur

sbRIO-9225

OPERATING INSTRUCTIONS AND SPECIFICATIONS

NI 9225E

3-Channel, 300 Vrms, 24-Bit, Simultaneous,

Channel-to-Channel Isolated Analog Input Module

NI 9225E Operating Instructions and Specifications 2 ni.com

This document describes how to use the National

Instruments 9225E and includes dimensions, terminal assignments,

and specifications for the NI 9225E. Visit

ni.com/info

and enter

rdsoftwareversion

to determine which software you need for

the modules you are using. For information about installing,

configuring, and programming the system, refer to the system

documentation. Visit

ni.com/info

and enter

cseriesdoc

for

information about C Series documentation.

Caution National Instruments makes no electromagnetic

compatibility (EMC) or CE marking compliance claims

for the NI 9225E. The end-product supplier is responsible

for conformity to any and all compliance requirements.

Caution The NI 9225E must be installed inside a suitable

enclosure prior to use. Hazardous voltages may be present.

NI 9225E Dimensions

The following figure shows the dimensions of the NI 9225E.

Figure 1. NI 9225E Dimensions in Millimeters (Inches)

73.4 (2.89)

0.0 (0.00)

26.7 (1.05)

58.4 (2.30)

66.0 (2.60)

0.0 (0.00)

NI 9225E Operating Instructions and Specifications 4 ni.com

Connecting the NI 9225E

The NI 9225E has three 2-terminal detachable screw-terminal

connectors that provide connections for three simultaneously

sampled, isolated analog input channels.

Figure 2. NI 9225E Terminal Assignments

AI0+

AI0–

AI1+

AI1–

AI2+

AI2–

You can connect ground-referenced or floating signal sources to

the NI 9225E. Connect the positive signal of the signal source to

the AI+ terminal, and connect the negative signal of the signal

source to the AI– terminal. If you make a ground-referenced

connection between the signal source and the NI 9225E, make sure

the voltage on the AI+ and AI– connections are in the

channel-to-earth safety voltage range to ensure proper operation of

the NI 9225E. Refer to the Specifications section for more

information about operating voltages and overvoltage protection.

Note You must use 2-wire ferrules to create a secure

connection when connecting more than one wire to a

single terminal on the NI 9225E.

Refer to Figures 3 and 4 for illustrations of how to connect

grounded and floating signal sources to the NI 9225E.

NI 9225E Operating Instructions and Specifications 6 ni.com

Figure 3. Connecting a Grounded Signal Source to the NI 9225E

Figure 4. Connecting a Floating Signal Source to the NI 9225E

NI 9225E

Signal

Source

AI–

–

AI+

NI 9225E

Signal

Source

AI–

–

AI+

The NI 9225E analog input channels are floating with respect to

earth ground and each other. The incoming analog signal on each

channel is conditioned, buffered, and then sampled by a 24-bit

Delta-Sigma ADC.

Each channel provides an independent signal path and ADC,

enabling you to sample all three channels simultaneously. Refer to

Figure 5 for an illustration of the circuitry for one channel of

the NI 9225E.

Figure 5. Input Circuitry for One Channel of the NI 9225E

NI 9225E

AI+

AI–

ADC

Amplifier

Overvoltage

Protection

Prefilter

NI 9225E Operating Instructions and Specifications 8 ni.com

Understanding NI 9225E Filtering

The NI 9225E uses a combination of analog and digital filtering

to provide an accurate representation of in-band signals while

rejecting out-of-band signals. The filters discriminate between

signals based on the frequency range, or bandwidth, of the signal.

The three important bandwidths to consider are the passband, the

stopband, and the alias-free bandwidth.

The NI 9225E represents signals within the passband, as quantified

primarily by passband flatness and phase nonlinearity. All signals

that appear in the alias-free bandwidth are either unaliased signals

or signals that have been filtered by at least the amount of the

stopband rejection.

Passband

The signals within the passband have frequency-dependent gain or

attenuation. The small amount of variation in gain with respect to

frequency is called the passband flatness. The digital filters of the

NI 9225E adjust the frequency range of the passband to match the

data rate. Therefore, the amount of gain or attenuation at a given

frequency depends on the data rate. Figure 6 shows typical

passband flatness for the NI 9225E.

Figure 6. Typical Passband Response of the NI 9225E

Frequency/Data Rate

0.50.4

0.025

0.000

–0.025

–0.050

0.30.20.10

Gain (dB)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Système d'E/S

National Instruments

National Instruments NI-9244 Manuel utilisateur

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments NI 9208E Manuel utilisateur

National Instruments

National Instruments 9224 Manuel

National Instruments

National Instruments PXIe-5764 Manuel du propriétaire

National Instruments

National Instruments NI PXI-7851 Manuel utilisateur

National Instruments

National Instruments USB-9211A Manuel utilisateur

National Instruments

National Instruments PXIe-5164 Manuel utilisateur

National Instruments

National Instruments NI 783xR Manuel utilisateur

National Instruments

National Instruments AT E Series Manuel utilisateur

National Instruments

National Instruments NI 9226 Manuel utilisateur

National Instruments

National Instruments M Series Manuel utilisateur

National Instruments

National Instruments PXI-6289 Manuel utilisateur

National Instruments

National Instruments NI 9226 Manuel

National Instruments

National Instruments NI 9375 Manuel utilisateur

National Instruments

National Instruments PXIe-4480 Manuel utilisateur

National Instruments

National Instruments NI 9411 Manuel utilisateur

National Instruments

National Instruments PXIe-4339 Manuel utilisateur

National Instruments

National Instruments 9232 Manuel

National Instruments

National Instruments NI 9225 Manuel utilisateur

National Instruments

National Instruments USB-9421 Manuel utilisateur

National Instruments

National Instruments PXI-7854 Manuel utilisateur

National Instruments

National Instruments NI SCB-68 HSDIO Mode d’emploi

National Instruments

National Instruments R Series Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur