National Instruments 73 Series Manuel utilisateur

GETTING STARTED

NI SMD-7610 Stepper Drives

and NI 73xx Motion Controllers

This document explains how to install and configure the NI SMD-7610 stepper drives for use

with the NI 7330/7340/7350 motion controllers.

Tip If you encounter any problems during setup, refer to the Worldwide Support

and Services section for assistance.

Contents

What You Need to Get Started ................................................................................................. 2

Hardware .......................................................................................................................... 2

Software............................................................................................................................ 2

Hardware Configuration and Installation ................................................................................. 3

Step 1: Install NI-Motion.................................................................................................. 3

Step 2: Install the NI 73xx Motion Controller.................................................................. 4

Step 3: Install Software on and Configure the RT PXI Controller

(PXI Motion Controllers Only) ..................................................................................... 5

Step 4: Connect and Configure the NI UMI-7764 ........................................................... 7

Step 5: Connect the Drive Command Signals to the UMI-7764 ...................................... 8

Step 6: Connect the Drive Enable Signal to the UMI-7764 ............................................. 10

Step 7: (Optional) Connect the Drive Fault Signal to the UMI-7764 .............................. 10

Step 8: (Optional) Connect the Encoder Signals to the UMI-7764.................................. 10

Step 9: Connect the NI PS-12/13 Power Supply to the NI SMD-7610............................ 11

Step 10: Connect the SMD-7610 to the Motor................................................................. 12

Step 11: Configure the NI SMD-7610 DIP Switches....................................................... 13

Step 12: Power on the Drive and Verify Connections...................................................... 16

Software Installation and Configuration................................................................................... 16

Step 1: Update Firmware on the Motion Controller......................................................... 16

Step 2: Configure the NI Motion Controller .................................................................... 17

Step 3: Test the Motor In MAX........................................................................................ 18

Where to Go Next..................................................................................................................... 19

Worldwide Support and Services ............................................................................................. 20

2|ni.com |Getting Started with NI SMD-7610 and NI 73xx

What You Need to Get Started

You need the following items to get started.

Note You cannot connect the NI SMD-7610 to NI 73xx motion controllers using

the NI UMI-7772/7774.

Hardware

A computer with an available PXI or PCI slot

NI 7330, NI 7340, or NI 7350 motion controller

UMI-7764

SH68-C68-S cable to connect your NI UMI and motion controller

+5 V power supply for the UMI-7764

Snap-on ferrite bead for the power supply cable (included with your NI UMI-7764). Refer

to the UMI-7764 User Guide and Specifications for installation information.

NI SMD-7610 stepper drive

NI PS-12 or NI PS-13 power supply for the NI SMD-7610

NI or third-party stepper motor

Note NI offers stepper motors matched to the NI SMD-7610. Refer to ni.com/

motion for motor options. National Instruments highly recommends using these

motors for the best user experience.

(optional) ENC-7740 encoder for ST17 motors (NI part number 748991-01) or ENC-7741

encoder for ST23 motors (NI part number 748992-01)

NI-7748 encoder cable to connect the encoder to the UMI-7764 (NI part number 748994-01)

Software

NI-Motion 7.6 or later driver software

Tip Refer to KB 4WRDJ3WA, Which LabVIEW Version Supports NI-Motion?, at

ni.com/kb, for NI-Motion/LabVIEW version compatibility information.

One of the following software packages and documentation:

– LabVIEW 8.5 or later

– LabWindows™/CVI™8.5 or later

– Microsoft Visual C++ 6.0

– Microsoft Visual Basic 6.0

Getting Started with NI SMD-7610 and NI 73xx |© National Instruments |3

Figure 1 shows the hardware connections using a UMI-7764.

Figure 1. UMI-7764 to NI SMD-7610 Drive Connections

Hardware Configuration and Installation

This section covers the hardware setup for the NI motion controller, NI UMI-7764, and

NI SMD-7610 stepper drive.

Caution Before installing the NI 7330/7340/7350 motion controller refer to the

user manual appropriate to your controller for safety and specification information.

Failure to follow safety instructions may result in damage to equipment.

Step 1: Install NI-Motion

You must install the NI-Motion driver software before installing an NI motion controller for the

first time. If you are upgrading from a previous version of NI-Motion, it is not necessary to

remove the NI motion controller before installing the upgrade. The upgrade does not affect the

existing Microsoft Windows configuration.

Note If you are using a Real-Time OS, install LabVIEW Real-Time on the

development computer before installing NI-Motion so that the RT support files

install.

Complete the following steps to install the NI-Motion driver software:

Note When installing NI-Motion, you must be logged on with administrator-level

access. After you have restarted the system, you may need to refresh Measurement &

Automation Explorer (MAX) to view the new controller.

SH68-C68-S

Cable

NI PS-12/13

Power Supply

NI SMD-7610

Stepper Drive

UMI-7764

+5 V Power

Supply

LN-V+V

Madein China

+V ADJ

OUTPUT:48V 6.7A INPUT:100-240VAC 5A 50/60Hz

LN-V+V

Madein China

+V ADJ

Encoder

Connections

I/O Connections

12345678

NI Stepper Motor

4|ni.com |Getting Started with NI SMD-7610 and NI 73xx

1. Insert the NI-Motion CD into the CD-ROM drive to display the NI-Motion installation

screen, or download the latest version from ni.com/downloads.

2. If you have autorun enabled, autorun.exe runs automatically. Otherwise, double-click

autorun.exe.

3. Follow the onscreen instructions.

Note You must update the firmware on your NI motion controller(s) before you can

use them with the corresponding version of NI-Motion. Refer to Step 1: Update

Firmware on the Motion Controller in the Software Installation and Configuration

section for detailed instructions.

Step 2: Install the NI 73xx Motion Controller

The following sections explain how to install PXI and PCI motion controllers.

PXI Controllers

1. Power off and unplug the chassis.

Caution To protect yourself and the computer from electrical hazards, the

computer must remain unplugged until the installation is complete.

2. Choose an unused peripheral slot and remove the filler panel.

3. Touch a metal part on the chassis to discharge any static electricity that might be on your

clothes or body. Static electricity can damage the controller.

4. Insert the PXI controller into the chosen slot. Use the injector/ejector handle to fully secure

the device into place.

5. Attach the front panel of the PXI controller to the front panel mounting rails of the chassis

with the slot screws on the chassis.

Caution Always power on the computer containing the motion controller and

initialize the controller before you power on the rest of the motion system. Power off

the motion system in the reverse order.

6. Plug in and power on the chassis.

PCI Controllers

1. Power off and unplug the computer.

Caution To protect yourself and the computer from electrical hazards, the

computer must remain unplugged until the installation is complete.

2. Open the computer case to expose access to the PCI expansion slots.

3. Touch a metal part on the chassis to discharge any static electricity that might be on your

clothes or body. Static electricity can damage the controller.

Getting Started with NI SMD-7610 and NI 73xx |© National Instruments |5

4. Choose an unused +3.3 V or +5 V PCI slot, and remove the corresponding expansion slot

cover on the back panel of the computer.

5. Gently rock the controller into the slot. The connection may be tight, but do not force the

controller into place.

Note Check that the bracket of the device aligns with the hole in the back panel rail

of the computer chassis.

6. Secure the mounting bracket of the controller to the back panel rail of the computer.

7. Replace the cover.

Caution Always power on the computer containing the motion controller, and then

initialize the controller before you power on the rest of the motion system. Power off

the motion system in the reverse order.

8. Plug in and power on the computer.

Step 3: Install Software on and Configure the RT PXI

Controller (PXI Motion Controllers Only)

Note This step is only required if you are using a PXI-7330/7340/7350 motion

controller and an RT PXI controller. If you are not using an RT PXI controller, skip

to the Step 4: Connect and Configure the NI UMI-7764 section.

Complete the following steps to configure the controller and install software on it.

Note The Measurement & Automation Explorer (MAX) user interface may not

match these steps exactly depending on which version of MAX you are using.

1. Boot the NI PXI embedded controller into the real-time operating system. The PXI

controller automatically boots into LabVIEW RT Safe Mode when no software is installed.

LabVIEW RT Safe Mode loads with the basic real-time operating system and automatically

attempts to connect to the network using DHCP. If DHCP is not available, the controller

connects to the network with a link-local IP address.

Tip You can connect a monitor to the PXI to display startup messages such as the

IP address and MAC address.

2. Launch Measurement & Automation Explorer (MAX) on the development computer by

clicking the MAX icon on the desktop ( ), or by selecting Start»All Programs»

National Instruments»Measurement & Automation.

3. Expand the Remote Systems branch. MAX lists the PXI controller as the model name of

the controller followed by the MAC address (for example, NI-PXI-8104 00802f108562).

6|ni.com |Getting Started with NI SMD-7610 and NI 73xx

Tip Record the PXI controller MAC address, located on the side of the controller,

for use in identifying the controller. The label also can be removed and placed on the

front of the controller for easier access. If you have connected the PXI controller to a

monitor, the MAC address also appears when the PXI system boots up.

4. Select the System Settings tab and type a descriptive name for the system in the Name

field.

5. (Optional) Complete this step only if the target has an empty IP address (0.0.0.0). Select the

Network Settings tab and select DHCP or Link Local from the Configure IPv4 Address

list to assign an IP address or select Static to specify a static IP address in the IPv4 Address

section.

6. Click Save on the toolbar and let MAX reboot the system.

7. When the new system name appears under Remote Systems, expand the controller item in

the tree, right-click Software, and select Add/Remove Software.

8. Install the LabVIEW Real-Time software and NI-Motion on the RT target. Go to

ni.com/info and enter etspc for the latest information about supported software.

9. Click Next to install the selected software on the controller. Click Help if you need

information about installing recommended software sets.

10. Wait for installation to complete, then click Finish.

11. Expand the Devices and Interfaces item under the PXI system.

12. Right-click the remote motion controller icon and select Map to Local Machine. This

assigns a local board ID to the remote motion controller in the host system.

Mapping the remote controller into the local system allows you to configure the controller

through MAX exactly as you would a controller that is in the host system. You can initialize

the controller, download firmware, and use the interactive and configuration panels exactly

as you would on a controller installed in the host machine. You also can write VIs using the

remote motion controller through the local board ID assigned to it.

This allows you to write and debug your VIs on the host, and then download them to the

remote system when you are ready. All you need to change is the board ID in your VI from

the locally assigned Board ID to the ID assigned by the remote system.

13. Browse to Devices and Interfaces under My System, where there is a shortcut icon next

to a new controller name.

For example, if the motion controller on the remote system is a PXI-7354, and the remote

system has an IP address of 123.45.678.9, then the shortcut device would show a name

like PXI-7354 (X) on 123.45.678.9 (Y).

Xis the board ID assigned to the board by the remote system. Use this board ID for VIs that

are downloaded to the remote system through LabVIEW RT.

Yis the board ID assigned to the remote motion controller by the local system. Use this

board ID for any VIs that run on the host and use the remote motion controller.

14. Close MAX.

Getting Started with NI SMD-7610 and NI 73xx |© National Instruments |7

Step 4: Connect and Configure the NI UMI-7764

Complete the following steps to connect and configure your UMI-7764.

Tip For more information about connecting external power, encoders, and other

motion I/O signals, refer to the Universal Motion Interface (UMI)-7764 User Guide

and Specifications.

1. Connect the SH68-C68-S 68-pin shielded cable between the Motion I/O connector on the

NI 73xx motion controller and the Motion I/O connector on the UMI-7764.

2. Configure the UMI-7764 DIP switches. You must set the DIP switches to the following

settings to match the polarity configuration for the SMD-7610 stepper drive:

• Inhibit Input (S2)—Active Low

• Inhibit Output (S1)—Active Low

The UMI-7764 DIP switch configuration is shown in Figure 2.

Figure 2. UMI-7764 Inhibit Input and Inhibit Output DIP Switch Settings

3. Connect an external +5 V power supply to the UMI-7764 Power Input Terminal Block. This

connection is required to power the encoder circuitry that converts differential encoder

signals to single-ended signals for the motion controller, as well as to power the UMI-7764

Inhibit Output signals.

Caution Do not plug in or turn on any power to the system until after all hardware

connections are complete.

1Inhibit Input Polarity Switch (S2) 2 Inhibit Output Polarity Switch (S1)

BP4

BP3

BP2

BP1

GND

+5 V

TRIG4

TRIG3

TRIG2

TRIG1

ASSY186343A-01

UMI-7764

FWDLIM1

HOME1

REVLIM1

AXIS1

FWDLIM3

HOME3

REVLIM3

AXIS3

AIGND

AREF

AIN4

AIN3

AIN2

AIN1

FWDLIM2

HOME2

REVLIM2

AXIS2

FWDLIM4

HOME4

REVLIM4

AXIS4

GND

NC1

SHUTDOWN

INH ALL

S2 S1

ACTIVE

HIGH LOW

8|ni.com |Getting Started with NI SMD-7610 and NI 73xx

Figure 3 shows the location of the UMI 7764 Power Input Terminal Block.

Figure 3. UMI-7764 Power Input Terminal Block

Step 5: Connect the Drive Command Signals to the

UMI-7764

Complete the following steps to connect the Drive Command signals to the UMI-7764.

1. Connect the SMD-7610 STEP terminal to the Motion I/O terminal block STEP (CW)1

terminal.

2. Connect the SMD-7610 DIR terminal to the Motion I/O terminal block DIR (CCW)1

terminal.

3. Connect the SMD-7610 COM+ terminal to the Motion I/O terminal block +5V terminal.

BP4

BP3

BP2

BP1

GND

+5 V

TRIG4

TRIG3

TRIG2

TRIG1

ASSY186343A-01

UMI-7764

FWDLIM1

HOME1

REVLIM1

INHIN1

GND

AOUT1*

AOGND*

INHOUT1

STEP(CW)1

DIR(CCW)1

+5 V

GND

ENCA1

ENCB1

INDEX1

AXIS1

FWDLIM3

HOME3

REVLIM3

INHIN3

GND

AOUT3*

AOGND*

INHOUT3

STEP(CW)3

DIR(CCW)3

+5 V

GND

ENCA3

ENCB3

INDEX3

AXIS3

REQUIRED INPUTS

+5V GND

AIGND

AREF

AIN4

AIN3

AIN2

AIN1

FWDLIM2

HOME2

REVLIM2

INHIN2

GND

AOUT2*

AOGND*

INHOUT2

STEP(CW)2

DIR(CCW)2

+5 V

GND

ENCA2

ENCB2

INDEX2

AXIS2

FWDLIM4

HOME4

REVLIM4

INHIN4

GND

AOUT4*

AOGND*

INHOUT4

STEP(CW)4

DIR(CCW)4

+5 V

GND

ENCA4

ENCB4

INDEX4

AXIS4

GND

NC1

SHUTDOWN

INH ALL

S2 S1

ACTIVE

INHOUT

INHIN

S1S2

HIGH LOW

Power Input

Terminal Block

Getting Started with NI SMD-7610 and NI 73xx |© National Instruments |9

Figure 4 shows the SMD-7610 Drive Command and I/O Connector location and pinout.

Figure 4. SMD-7610 Drive Command and I/O Connector

Figure 5 shows the UMI-7764 Motion I/O terminal block location and pinout.

Figure 5. UMI-7764 Motion I/O Terminal Block

12345678

OUT+

OUT-

COM+

STEP

DIR

BP4

BP3

BP2

BP1

GND

+5V

TRIG4

TRIG3

TRIG2

TRIG1

ASSY186343A-01

UMI-7764

FWDLIM1

HOME1

REVLIM1

INHIN1

GND

AOUT1*

AOGND*

INHOUT1

STEP(CW)1

DIR(CCW)1

+5V

GND

ENCA1

ENCB1

INDEX1

AXIS1

FWDLIM3

HOME3

REVLIM3

INHIN3

GND

AOUT3*

AOGND*

INHOUT3

STEP(CW)3

DIR(CCW)3

+5V

GND

ENCA3

ENCB3

INDEX3

AXIS3

REQUIRED INPUTS

+5V GND

AIGND

AREF

AIN4

AIN3

AIN2

AIN1

FWDLIM2

HOME2

REVLIM2

INHIN2

GND

AOUT2*

AOGND*

INHOUT2

STEP(CW)2

DIR(CCW)2

+5V

GND

ENCA2

ENCB2

INDEX2

AXIS2

FWDLIM4

HOME4

REVLIM4

INHIN4

GND

AOUT4*

AOGND*

INHOUT4

STEP(CW)4

DIR(CCW)4

+5V

GND

ENCA4

ENCB4

INDEX4

AXIS4

GND

NC1

SHUTDOWN

INH ALL

S2 S1

ACTIVE

INHOUT

INHIN

HIGH LOW

Axis 1 Motion I/O

Terminal Block

FWDLIM1

HOME1

REVLIM1

INHIN1

GND

AOUT1*

AOGND*

INHOUT1

STEP(CW)1

DIR(CCW)1

+5 V

GND

ENCA1

ENCB1

INDEX1

AXIS1

10 |ni.com |Getting Started with NI SMD-7610 and NI 73xx

Step 6: Connect the Drive Enable Signal to the UMI-7764

The Drive Enable signal controls the enable function of the drive. To use this signal, connect the

EN terminal to the Motion I/O terminal block INHOUT1 terminal.

Step 7: (Optional) Connect the Drive Fault Signal to the

UMI-7764

Complete the following optional steps to connect the drive fault signal to monitor the SMD-7610

for faults.

1. Connect the OUT+ terminal to the Motion I/O terminal block INHIN1 terminal.

2. Connect the OUT- terminal to the Motion I/O terminal block GND terminal.

Step 8: (Optional) Connect the Encoder Signals to the

UMI-7764

If your motor includes an encoder, connect the encoder signals to the UMI-7764.

1. Connect one end of the encoder cable to the encoder.

2. Cut the 15-pin DSUB connector off of the other end of the cable and expose the encoder

wires.

3. Connect the encoder wires to the UMI-7764 as indicated in Table 1.

4. Insulate any unused wires.

Table 1. Encoder to UMI-7764 Motion I/O Terminal Block Connections

Encoder

Signal Name

Encoder Cable

Wire Color

Motion I/O Terminal Block

Signal Name

Ablue ENCA1

Ablue/white ENCA1

Byellow ENCB1

Byellow/white ENCB1

Iorange INDEX1

Iorange/white INDEX1

GND black GND

+5V red +5 V

Autres manuels pour 73 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Contrôleurs

National Instruments

National Instruments 73 Series Manuel utilisateur

National Instruments

National Instruments NI 8350 Manuel utilisateur

National Instruments

National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Manuel utilisateur

National Instruments

National Instruments NI-488.2M Manuel utilisateur

National Instruments

National Instruments GPIB-VXI/C Manuel utilisateur

National Instruments

National Instruments GPIB-1284CT Manuel utilisateur

National Instruments

National Instruments 187970E-01 Manuel utilisateur

National Instruments

National Instruments GPIB-232CT-A IBCL EPROM Manuel utilisateur

National Instruments

National Instruments NI 9514 Manuel utilisateur

National Instruments

National Instruments 7330 Manuel utilisateur

National Instruments

National Instruments 7932 Manuel utilisateur

National Instruments

National Instruments PCI-7340 Manuel utilisateur

National Instruments

National Instruments cRIO-9064 Manuel utilisateur

National Instruments

National Instruments NI cRIO-9036 Manuel utilisateur

National Instruments

National Instruments PXI-8195 Manuel utilisateur

National Instruments

National Instruments IC-3120 Manuel utilisateur

National Instruments

National Instruments SCXI USB-1357 Manuel utilisateur

National Instruments

National Instruments PXIe-8861 Manuel utilisateur

National Instruments

National Instruments cDAQ-9132 Manuel utilisateur

National Instruments

National Instruments NI cDAQTM-9138 Manuel utilisateur

National Instruments

National Instruments cDAQ-9133 Manuel utilisateur

National Instruments

National Instruments IC-3120 Manuel utilisateur

National Instruments

National Instruments GPIB-110 Manuel utilisateur

National Instruments

National Instruments PXI NI PXI-8105 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur