Nady Systems 9E3W1KUH Manuel utilisateur

UHF Wireless Microphone Syetem

USER MANUAL

Welcome to select UHF wireless microphone system, and welcomes you

to join our clients team. UHF wireless microphone system is a professional

design and production, with the perfect professional sound quality, using the

world's most advanced multi-channel digital phase-locked loop of the DPLL

frequency synthesis, UHF ultra-high frequency band, the real diversity.

Available 9 group, 99-channel selection, can avoid all kinds of interference, the

system runs more stable, more reliable transmission. And infrared channels to

recover automatically locks and locking systems and other innovative design

allows you to more easily use the system, operation is simple and clear. Our

ultimate goal is to design the most perfect embodiment of the sound system

functions.

Wireless receiver function

☞Wireless receiver control panel Description

ⅰReceiver Front panel

●

1Volume indicator: Has four green and one red light, the number of the

green light is means the voice value. If it was red light, then the voice is

high enough and distortion, please turn down the value.

●

2 LED :Display group、channel、volume、signal

●

3 Function keys:Press SET button to select the main menu one by one

in a cycle,press“▲”“▼”button to change or confirm the current state of

the selected menu,then press the SET button again to make the setting in effect,hold

the “▲”“▼” button for a long time to quickly select the frequency and channel.

●

4 Infrared light: When press“ACT”key，The light is working.

●

5 Infrared frequency button:press “ACT”button, Channel parameters will

be transmitted to the transmitter.

●

6 Power on/off Switch:press “POWER”button, Open the receiver power.

ⅱ Receiver back panel diagram

●

7 Socket: 12V DC power supply input socket, Socket connection is the

center electrode voltage.

●

8 Audio Balanced Output: The use of "XLR"-type socket, Two-channel

signal separately output.

●

9 Audio Mixed Output: Two signals will be mixed with the output

●

10 Antenna Socket:

☞Receiver LCD Description

●

1 Group menu display: Displays the current working group.

●

2 Channel menu display:Indicating that the current operating channel.

●

3 Volume menu display:to display volume signals.

●

4 Signal menu display: display the current signal strength.

●

5 Antennas display.

☞The Steps of turning on receiver

1. Open the receiver power

2. Then turn on the transmitter,adjust receiver’s volume to

a proper level,then make sound towards microphone then we

can see microphone volume indication field on receiver’s

audio level meter is illuminated.if no audio output,or level

meter is not illuminated,please examine the device.

3.When system is not in application for a long period of

time,please turn the device off and take out the battery.

☞Receiver Operating Instruction

Note: After confirm whenever functions are selected to change, LCD

screen will be flashing, after 9 second the stop flashing, Change

in force,press "SET" button to confirm after the flashing stop.

ⅰ Automatic Frequency Operation

Press “SET”button ,make transmitter point at receiver’s infrared

automatic freqency window,and hold it for 2-3 seconds;Receiver’s

channel parameters shall be sent to transmitters via infrared data.

ⅱ Group settings

Press "SET" button to enable LCD in "GROUP" flashing, And

then press "▲" or "▼" button to change the group number,

press "SET" button to confirm. (0-9 class has optional).

ⅲ Channel settings

Press "SET" button to enable LCD in "CHANNEL" flashing, And

then press "▲" or "▼" button to change the group number, press

"SET" button to confirm. (0-99 class has optional).

ⅳ Volume settings

Press "SET" button to enable LCD in "vol" flashing, And then

press"▲" or "▼" button to change the volume signals, click "SET"

button to confirm. (0-63 class has optional).

Handheld Transmitter Features

☞Handheld Transmitter Control Description

Note: how to use the built-in button!

Picture 1

Picture 2

Holding hand-held transmitter of the upper part of cylindrical

shell (arrows in Picture 1), the arrow shown in Picture 1 spin

out of the lower part of shell, as shown in Picture 2 the arrow

to pull down, you can reveal a built-in button .

ⅰ Handheld transmitter positive map

●

1 Microphone Head:Includes Microphone grille and microphone capsule.

●

2 Tube body: Containing batteries 、transmitter PCB, built-in

function keys, built-in transmitting antenna tail.

●

3 LCD screen:display Group、Channels and battery.

●

4 Up and down select keys (built-in): Press "▲" "▼" button to select

the menu on the current state of change, can change the Working Group

or Channel.( use same as the receiver)

●

5Settings button (the built-in): Press "SET" key to select

the main menu cycle, also can change the settings to confirm.

Change the settings if confirmed, LCD screen will be

flashing to remind, after 9 seconds flashing to stop, change

the entry into force.

●

6Built-in high and low transmission power change-over switch

●

7Power switch: On/OFF

ⅱ Handheld transmitter back of map

●

8 Infrared auto frequency window,by operating “SET” button of receiver,channel

parameters shall be sent to transmitter.

●

9 Battery Tray

☞ Handheld Transmitter LCD Instruction

●

1Group display:display the current operating group.

●

2 Channel display:display the current operating channel.

●

3 Battery display:display the current remaining battery capacity.

Battery Operation Instruction

☞Handheld transmitter battery installation

1. Holding hand-held transmitter of the upper part of

cylindrical shell (arrows in Picture 1), the arrow shown

in Picture 1 spin out of the lower part of shell, as shown

in Picture 2 the arrow to pull down, exposing the battery

positions.

Picture 1

Picture 2

2. Put two new AA alkaline batteries on the 5th. Make sure that

the polarity of the battery install (Figure). Warning: Do

not install the wrong battery polarity, which may damage

electronic components within the transmitter.

3. Afresh spin on transmitter lower part case

☞Body Pack Transmitter Battery Instruction

1. Soft depress battery cover on both sides, can open the battery

warehouse.( following diagram)

2. Put two new AA alkaline batteries on the 5th. Make sure that the

polarity of the battery install(Follow the battery polarity

warehouses instructions)

3. Cover positions back to the battery cover

(Note:When system is not in application for a long period of

time,please turn the device off and take out the battery.)

Notes

＊Please choose non-intermodulation frequency setting.within 50 MHz

bandwidth,Usually 4-8 transmitters can be used at the same time.If more

sets of wireless microphones are needed,devices with other frequency

band should be applied.

＊There should be appropriate distance between the receiver and

transmitter,not too near,at least 1 meter distance.

＊If receiving condition seems not to be as good as expected,extended

cord,exterior high-gain antenna,and even antenna amplifier can be

applied.

＊The receiver and transmitter must be set the same frequency channel.

＊When several sets of receivers are used together,it is recommended to

use high-gain antenna,antenna amplifier and receive branch unit.

＊When receiver adopts the omni-directional antenna,please keep the

antenna away from the wall at least 0.5 mm,and also away from any other

metal objects.

＊The transmitter should at least 20cm apart when multiple transmitters

are used together,so as not to interfere each other

＊When you use Handheld Microphone,please hold the middle of the

mic.Body.If too close to the Microphone grille,it will affect the sound

pick-up;if too Close to the antenna (at the bottom of the

microphone),transmission efficiency and working distance may be

reduced.

＊Increase and reduce treble or bass by adjust the distance between

microphone and mouth.

＊The Body Pack Transmitter adopts 1/4 wavelength whip antenna,please

never let the antenna contact human body directly,nor tie with the

microphone caoble together,otherwise it will reduce the operation

effects.

＊To reduce the voice fluctuation when head moves,please keep the

collar-worn microphone as close as possible to the middle,and the

microphone connections should also be fixed tightly to avoid friction

noise.

＊When collarworn microphone is applied for live sound

reinforcement,directional microphone capsule should be used.Selection

and position arrangement of speakers should be made in consideration of

feedback elimination.When necessary,feedback destoryer should be

equipped.

Trouble Clearing

Problems Solutions

No indication on receiver Link the power supply cable well

Audio signal distortion,

Extra noise

Remove the RF interference sources nearby

(such as CD players,computers,digital

devices,earphones monitoring system)

Receiver can not receive RF signal Check the reception range

Unable to turn on transmitter Replace batteries

Notes

If problems are not in the above list,please contact the local

maintenance staff or call us directly.Wireless microphone system can

not be in rain or placed in moist environment.It can not be exposed to

strong direct sunlight,or in high temperature environment.It also can

not be shocked,vibrated or thrown.To reduce the risk of electric shock

or damage to device,please do not remove the machine cover.Only use the

supplied power adaptor,otherwise it might damage the equipment.

Autres manuels Nady Systems Système de microphone

Nady Systems

Nady Systems 401X Quad Manuel utilisateur

Nady Systems

Nady Systems ALD-800 Manuel utilisateur

Nady Systems

Nady Systems DKW-8U Manuel utilisateur

Nady Systems

Nady Systems IRW-220X Manuel utilisateur

Nady Systems

Nady Systems UB-10 Manuel utilisateur

Nady Systems

Nady Systems PEM-500 Manuel utilisateur

Nady Systems

Nady Systems 4W-1KU Manuel utilisateur

Nady Systems

Nady Systems AMERICAN STARPOWER X2 Manuel utilisateur

Nady Systems

Nady Systems DKW-3 LT Manuel utilisateur

Nady Systems

Nady Systems PEM-1000 Manuel utilisateur

Nady Systems

Nady Systems DKW-1 Manuel utilisateur

Nady Systems

Nady Systems 151 VR Manuel utilisateur

Nady Systems

Nady Systems Encore I Manuel utilisateur

Nady Systems

Nady Systems 351 VR Manuel utilisateur

Nady Systems

Nady Systems DKW Duo Manuel utilisateur

Nady Systems

Nady Systems VR-3U Manuel utilisateur

Nady Systems

Nady Systems ENC Duet Manuel utilisateur

Nady Systems

Nady Systems UHF-4 Manuel utilisateur

Nady Systems

Nady Systems MRX-16 Manuel utilisateur

Nady Systems

Nady Systems DKW-3 Manuel utilisateur

Nady Systems

Nady Systems MGT-16 Manuel utilisateur

Nady Systems

Nady Systems U-800 Manuel utilisateur

Nady Systems

Nady Systems UB-16 Manuel utilisateur

Nady Systems

Nady Systems UHF-24 Manuel utilisateur

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Tekon

Tekon DUOS Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur