Murphy PowerCore MPC-20 Manuel utilisateur

00-02-0897

2015-10-22

Section 40

PowerCore



Model MPC-20

Installation Manual

*Approved by CSA for non-hazardous locations (Group Safety Publication IEC 61010-

1 Third Edition).

Products covered in this document comply with European Council electromagnetic

compatibility directive 2004/108/EC and electrical safety directive 2006/95/EC.

In order to consistently bring you the highest quality, full featured products, we reserve the

right to change our specifications and designs at any time. The latest version of this

manual can be found at www.fwmurphy.com.

BEFORE BEGINNING INSTALLATION OF THIS MURPHY

PRODUCT:

•Read and follow all installation instructions.

•Visually inspect this product before installation for

any damage during shipping.

•Disconnect all electrical power to the machine.

Failure to do this before welding can result in

damage to the panel and/or its components.

•It is your responsibility to have a qualified

technician install the unit and make sure the

installation conforms to local codes Including but

not limited to double insulation and fire

containment.

•Observe all Warnings and Cautions in each

section of these instructions.

•The MPC-20 is designed for use in industrial

environments for monitoring and control which

include engine driven pumps, compressors,

grinders, chippers, & rock crushers. Potential

difficulties may exist when ensuring

electromagnetic compatibility in other

environments due to conducted as well as

radiated disturbances.

Contact Enovation Controls Technical Service if you

have any questions or concerns at: +1 918-317-4100.

IMPORTANT! Improper use and operation of electronic

products can be dangerous. It is required that point-of-

operation guarding devices be installed and maintained.

All such devices must meet OSHA and ANSI Machine

safety standards. The manufacturer shall not accept

any responsibility for installation, application, or safety

of systems.

Table of Contents

Operations Manual Location...............................................1

Hardware Installation ...........................................................1

Inspecting Package Contents.....................................1

Tools Needed .............................................................1

Installation ..................................................................2

Dimensions for Installation .................................................4

Wiring Instructions ...............................................................6

PIN Specifications for FCI Connection .......................6

Connector...................................................................7

Accessories ...........................................................................8

Specifications........................................................................9

Electrical.....................................................................9

Environmental...........................................................10

Mechanical ...............................................................10

Mounting Template............................................................ 11

Panel Opening Cutout ..............................................11

-NOTES-

LENS CLEANING PROCEDURES

The lens on the MPC-20 is composed of Polycarbonate

materials. Use only mild soap and water to clean the

lens/display window. Evidence of improper cleaning

techniques or chemicals includes cracks, smear marks,

scratches, or fogged/hazy lenses.

Section 40 00-02-0897

2015-10-22 - 1-

Operations Manual Location

After installation, please review the MPC-20 Operations Manual

prior to placing the controller into service. In order to access the

MPC-20 Operation Manual please visit the MPC-20 product

page to download or print a copy located under the literature tab.

www.fwmurphy.com/mpc-20

Hardware Installation

The following instructions will guide you through installing the

MPC-20 controller.

Inspecting Package Contents

Before attempting to install the product, it is recommended that

you ensure all parts are accounted for and inspect each item for

damage (which sometimes occurs during shipping). The items

included in the box are:

MPC-20 Controller kit – P/N 40-70-0490 includes:

•MPC-20 Controller

•4 (6-32) mounting screws

•4 (#6) lock washers

•P/N 00-02-0897 MPC-20 Installation Manual

Tools Needed

Use a ¼” drill bit to make the approximately sized 0.250”

mounting holes.

Section 40 00-02-0897

2015-10-22 - 2-

Installation

Preparing the Enclosed Panel

Determine the location of the MPC-20 on the customer-supplied

flat or enclosed panel. The suitability of the enclosure is subject

to investigation by the local authority having jurisdiction at the

time of the installation.

Use the Installation Template measurements (included at the

end of the manual) as a guideline to cut a hole to the specified

dimensions. Drill holes where indicated on the template for the

mounting screws. Please read IMPORTANT note below:

IMPORTANT: When using the paper template

from the manual, please be aware that the drawing

is not represented to scale. The measurements

provided are accurate, and should be referred to

when preparing the placement of the unit.

Once the holes are cut, check to make sure that there is

adequate clearance for the edges of the MPC-20 housing to

mount flush against the outside surface of your panel.

Recommended torque for tightening the mounting screws is 7.5-

inch pounds. Although not required, only Blue polycarbonate

compatible thread lock should be used for the MPC-20 mounting

screws if thread lock is desired.

Insert the MPC-20 controller from the front side of the panel and

install the four mounting screws and lock washers. Ensure that

there is a good seal between the controller, the gasket (if used)

and the mounting panel. Plan the MPC-20 mounting for easy

wiring and access.

Section 40 00-02-0897

2015-10-22 - 3-

Installing the Display

Place the back side of the display through the opening in the

panel.

1. Use the 4 screws to line up the unit with the drilled holes.

2. Ensure that the back of the case is flush.

3. Use the screws provided to tighten unit to the panel. Use

the appropriate wrench or socket to tighten. Torque

screws to 7.5 inch pounds.

MPC-20 Controller

(Accessory Item)

MPC Mounting /

Panel Gasket

Customer-supplied

panel

#6 Lock Washers

#6-32 Mounting

Screws

Section 40 00-02-0897

2015-10-22 - 4-

Dimensions for Installation

Front Inches

[mm]

Section 40 00-02-0897

2015-10-22 - 5-

Back

Side View

Section 40 00-02-0897

2015-10-22 - 6-

Wiring Instructions

PIN Specifications for FCI Connection

Wiring of this device must meet all applicable electrical codes.

Battery lines to the unit must all come through a single 10 Amp or less

fuse or circuit breaker to retain the controller’s CSA rating.

Autres manuels pour PowerCore MPC-20

Table des matières

Autres manuels Murphy Contrôleurs

Murphy

Murphy Engine Throttle Controller AT-67207 Manuel utilisateur

Murphy

Murphy Keystart 9700 Manuel utilisateur

Murphy

Murphy Autostart 710 AS710S Manuel utilisateur

Murphy

Murphy Autostart 705 AS705S Manuel utilisateur

Murphy

Murphy Autostart AS731 Manuel utilisateur

Murphy

Murphy Selectronic Micro-Controller Series 1500 Manuel utilisateur

Murphy

Murphy Automatic Engine Controller AS3000 Manuel utilisateur

Murphy

Murphy Automatic Engine Controller EA150 Manuel utilisateur

Murphy

Murphy EMS447 Manuel utilisateur

Murphy

Murphy Auto-Start/Stop Controller Cascade Manuel utilisateur

Murphy

Murphy Automatic Engine Controller A88 Manuel utilisateur

Murphy

Murphy CONNECT Manuel utilisateur

Murphy

Murphy PowerCore MGC1000 Manuel utilisateur

Murphy

Murphy EMS547 Manuel utilisateur

Murphy

Murphy LR857 Manuel utilisateur

Murphy

Murphy Autostart 730 AS730 Manuel utilisateur

Murphy

Murphy MX4 Series Manuel utilisateur

Murphy

Murphy EMS PRO Manuel utilisateur

Murphy

Murphy iGUARD AL-02058B Manuel utilisateur

Murphy

Murphy Cascade CD101 Manuel utilisateur

Murphy

Murphy PowerCore TEC-10 Manuel utilisateur

Murphy

Murphy Engine Throttle Controller AT-04060N Manuel utilisateur

Murphy

Murphy Glow Plug Control Module GPM92 Manuel utilisateur

Murphy

Murphy LR579 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur