Murphy CONNECT Manuel utilisateur

00-02-1165

2018-10-08

Section 40

Murphy CONNECT

Telematics for PowerCore



Products

Operations Manual

Initial Release for U.S. Only

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our

specifications and designs at any time.

Section 40 ii 00-02-1165

2018-10-08

BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT:

•Read and follow all installation instructions.

•Visually inspect this product before installation for any damage during

shipping.

•Disconnect all electrical power to the machine. Failure to do this before

welding can result in damage to the panel and/or its components.

•It is your responsibility to have a qualified technician install the unit and

make sure the installation conforms to local codes including but not

limited to double insulation and fire containment.

•Observe all Warnings and Cautions in each section of these instructions.

•The Murphy CONNECT product is a telemetry product designed for use

in industrial environments for remote monitoring and control when used

with Murphy’s PowerCore®family of controllers.

Contact Enovation Controls Technical Service if you have any questions or

concerns at: +1 918-317-4100.

IMPORTANT! Improper use and operation of electronic products can be

dangerous. It is required that point-of-operation guarding devices be installed

and maintained. All such devices must meet OSHA and ANSI Machine safety

standards. The manufacturer shall not accept any responsibility for installation,

application or safety of systems.

Section 40 300-02-1165

2018-10-08

Table of Contents

Introduction.................................................................................................................................5

Registering/Creating a New Account......................................................................................6

New Site Setup ...........................................................................................................................7

Adding New Site Personnel (Users) ........................................................................................9

Adding a New Child Site (Customer Site).............................................................................11

Adding, Deleting, and Moving Equipment............................................................................12

Site Equipment .........................................................................................................................14

Murphy CONNECT Specifications .........................................................................................22

Power Supply .............................................................................................................23

Inputs/Outputs............................................................................................................23

Communications ........................................................................................................23

Connection.................................................................................................................23

Physical / Environmental............................................................................................23

Section 40 400-02-1165

2018-10-08

The CONNECT device can be used for remotely starting an engine when used in conjunction

with Murphy’s PowerCorecontrollers and start unexpectedly. Please be cognizant at all times

of hands and other objects that are in close proximity to the machine(s) being controlled as they

may commence operation suddenly and without warning

Section 40 500-02-1165

2018-10-08

Introduction

The Murphy CONNECT telematics unit provides simple and dependable communication power

for PowerCorepanels and controllers. Murphy CONNECT is an easy, plug-and-play solution

for rental fleets, agriculture and pump systems as well as other PowerCore controller and

panel users wishing to automate or remotely monitor their engines.

The Murphy CONNECT unit is controlled from a cloud-based dashboard that provides secure

access from a computer or mobile device and is designed to be easy-to-use. LTE cell

technology provides worry-free data networking and allows you to stay connected from any

location. (LTE service required, 2-year service agreement included)

From the online dashboard, users can monitor their equipment's location using the unit's built-

in GPS and set radius alerts for when it moves. Users can also view trends based on an

engine’s usage, and control engine starts and stops while adjusting throttle functions for the

engine and application. The cloud-based system is also multi-user and multi-unit capable for

companies that need to provide access across several units, locations or employees.

Built to survive the same harsh conditions as the PowerCore controllers, the IP67-rated

telematics unit remains operational alongside PowerCore products with rugged protection from

freezing temperatures, extreme heat, moisture and dust.

Murphy CONNECT provides astounding benefits by helping reduce costs, prevent downtime

and optimize efficiency with intelligent analytics, real-time alerts and warnings.

Section 40 600-02-1165

2018-10-08

Registering/Creating a New Account

NOTE: In order to register/create a new account a Murphy CONNECT device

must be on hand that is not currently registered with another account.

Begin by going to the Murphy CONNECT webpage connect.enovationcontrols.com. There is a

yellow box labeled Register in the lower right side of the Login Box. Click the Register button to

begin registering a new account.

After clicking the register button on the login page the site will direct you to an Add New User

registration page. Fill out all necessary boxes in the form before clicking the button Create

Account. In order to submit the request a new Murphy CONNECT device is required.

Section 40 700-02-1165

2018-10-08

Once the new account is created the Sign In screen will be shown and allow the Admin to sign

in after filling out and submitting the registration form.

New Site Setup

Once registered and logged in, the Site will show the serial number of the unit used to register.

Click on the serial number under the map in the section labeled Connected Sites.

Section 40 800-02-1165

2018-10-08

Once the serial number has been clicked the site will open another page for form completion.

This form will allow naming of the site, site description, business name, contact phone,

contact email, time zone selection, site logo/image to be loaded, site address and site

personnel to be added/edited.

Section 40 900-02-1165

2018-10-08

Adding New Site Personnel (Users)

The CONNECT site allows for two different levels of users. The two levels are defined as Admin

and User for Site Personnel. To add a new User, select the site to which the user will be added.

Once on the site scroll down to the Site Personnel section and click New.

Fill in the new user information and click Create Account. Review the Admin and User sections

on the next page in order to decide which type of access to give the new user.

Section 40 10 00-02-1165

2018-10-08

User Information

This section provides identity information for other users registered on the site to be viewed

and contacted if needed.

•Title: This setting is only used for reference as the number of site personnel grows.

•Billing: This setting is to alert the particular user for subscription renewal.

This section provides the information for logging into the site with email and password. This

section also designates the level of access given to the user (User or Admin).

•User: User level users are able to login and see assigned sites as well as child sites,

view and control site equipment, view site personnel, acknowledge and delete alerts,

and view/export Device Status Trends.

•Admin: Admin level users are able to do everything the user level is able to do plus add

and remove users, move equipment from site to site, edit site information, add Child

Sites, turn on/off and change equipment Radius Alerts, load New CONNECT Firmware,

and perform equipment EZ Setup.

Alarm Notifications

This section provides the contact information to which alerts will be sent if desired when an

alert is present on the device/controller.

•Email: Enter the email address of any user desiring email notifications of existing

alarms.

•Mobile Text: Enter the mobile phone number of any user desiring mobile text

message notifications of existing alarms.

NOTE: Do not add a country code “1” for United States or place hyphens

in the number (e.g. 9183174100). Use the drop-down box to select the

carrier used for Text message notifications. Be sure to test the alert

notification to ensure the carrier setting is correct.

Table des matières

Autres manuels Murphy Contrôleurs

Murphy

Murphy Automatic Engine Controller A88 Manuel utilisateur

Murphy

Murphy PowerCore MPC-20 Manuel utilisateur

Murphy

Murphy Auto-Start/Stop Controller Cascade Manuel utilisateur

Murphy

Murphy Keystart 9700 Manuel utilisateur

Murphy

Murphy Engine Throttle Controller AT-04060N Manuel utilisateur

Murphy

Murphy iGUARD Manuel utilisateur

Murphy

Murphy iGUARD AL-02058B Manuel utilisateur

Murphy

Murphy MX4 Series Manuel utilisateur

Murphy

Murphy Autostart AS731 Manuel utilisateur

Murphy

Murphy Engine and Generator Controls Keystart 9620 Manuel utilisateur

Murphy

Murphy Selectronic Micro-Controller Series 1500 Manuel utilisateur

Murphy

Murphy PowerCore TEC-10 Manuel utilisateur

Murphy

Murphy Autostart 705 AS705S Manuel utilisateur

Murphy

Murphy LR579 Manuel utilisateur

Murphy

Murphy PowerCore MGC1000 Manuel utilisateur

Murphy

Murphy EMS447 Manuel utilisateur

Murphy

Murphy Automatic Engine Controller EA150 Manuel utilisateur

Murphy

Murphy EMS PRO Manuel utilisateur

Murphy

Murphy Autostart 710 AS710S Manuel utilisateur

Murphy

Murphy LR857 Manuel utilisateur

Murphy

Murphy Cascade CD101 Manuel utilisateur

Murphy

Murphy Glow Plug Control Module GPM92 Manuel utilisateur

Murphy

Murphy Cascade CD101 Manuel utilisateur

Murphy

Murphy Autostart 730 AS730 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur