Murphy Rack Puller RP75 Manuel utilisateur
RP-95028B/N
Revised 09-07
Catalog Section 40
(00-02-0106)
Rack Puller for Diesel Engines
Model RP75
■
Pulls Injection Pump or
Air Intake Shut-off Lever
■
30 lbf (133 N) Operating Force
■
Models Available for 12 or 24 Volt Systems
■
Operates on Signal from SWICHGAGE®
Installed on the Engine or Driven Equipment
Description
The RP75 rack puller is a semi-automatic device
that provides a pulling force to initiate shutdown
of diesel engines and equipment.
The RP75 connects to the injection pump or air
intake shut-off lever via a cable (chain optional).
A coil spring, within the RP75, is reset manually
and is held in place by an electromagnet. When
the SWICHGAGE®detects a malfunction, the
electromagnetic circuit is interrupted through a
Magnetic Switch–releasing the coil spring thus
pulling the cable/chain to actuate shutdown. The
spring, when fully compressed, exerts a pull of 30
lbf (133 N).
The RP75 is available for 12 or 24 VDC applica-
tions and is compatible with all SWICHGAGE®
instruments.
Specifications
Operating Force: 30 lbf (133 N) maximum,
10 lbf (44 N) minimum.
Coil Voltage: Specify 12 or 24 VDC.
Coil Resistance: RP75-12: 32.2 ohms.
RP75-24: 129.8 ohms.
Length of Travel: 1-7/8 in. (48 mm).
Control Linkage
•
Cable: 4ft. (1.22 m); Optional 8 ft. (2.43 m)
or 12 ft. (3.65 m) available.
•
Chain (optional): 30 in. (762 mm).
NOTE: Specify options when ordering.
Shipping Weight: 5 lbs 3 oz. (2.4 kg).
Shipping Dimensions: 9-1/4 x 8-1/4 x
5-1/4 in. (235 x 210 x 133 mm).
Dimensions How to Order
Specify model number.
RP75 – ____ – ____
Service Parts
Specify part number.
Part Number Description
40-00-0021 12 VDC core assembly
40-00-0044 Shaft solenoid assembly
40-01-0050 Bushing shaft assembly
40-01-0053 Case repair kit
40-01-0054 Cocking rod, bushing and
knob repair kit
40-05-0136 Spring, main actuating
40-05-0149 Spring, cocking rod return
80-04-1030 2 Screws, machined #10-24
x 3/8 pan HD steel CAD II
40-00-0024 24 VDC core assembly
Warranty
A limited warranty on materials and workmanship
is given with this FW Murphy product. A copy of
the warranty may be viewed or printed by going to
www.fwmurphy.com/support/warranty.htm
Voltage
12 = 12 VDC
24 = 24 VDC
Calibration
Blank = 4 ft. (1.2 m) cable
8 = 8 ft. (2.4 m) cable
12 = 12 ft. (3.7 m) cable
C = Chain 30 in. (762 mm)
Reset Knob
and Stem
3-1/4 in.
(83 mm)
10-1/4 in.
(260 mm)
3-3/4 in.
(95 mm) 1-1/4 in.
(32 mm)
2-3/8 in.
(60 mm)
Wiring
Terminals
Mounting
Studs
1/4-20
(4 places)
Side View
Rear View Mounting Hole
Dimensions
5-1/2 in.
(140 mm)
RP-95028B/N page 2 of 2
Mounting
1.
Mount the RP75 using a mounting bracket as illustrated in
Figure 1 (see page 1 of this bulletin for mounting hole dimen-
sions.). If installing the RP75 to an engine com-
partment firewall, go to Step 2.
2.
If installing the RP75 to an engine
compartment firewall, drill a 37/64
in. (15 mm) diameter hole in the
firewall (see Figure 2).
3.
Remove the reset knob on the RP75 by loosening the allenhead
screw on the knob.
4.
Remove the mounting nut and insert the RP75 reset stem
through the hole from the back of the firewall.
5.
Replace the mounting nut and tighten. Reinstall the reset knob.
Typical Wiring Diagrams
Wire the RP75 appropriately (see Figure 3). NOTE: RP75 is voltage
rated; do not apply 24 VDC to 12 VDC model and vice versa. Also,
the 117PH Magnetic Switch is rated for both 12 and 24 VDC circuits
but voltage must be specified when ordering the 518PH or 761APH
Magnetic Switches.
Installing Cable or Chain
1.
To install the control linkage (cable or chain), apply voltage to
the RP75. Push in the reset knob. If installing the cable, insert
the cable attaching nut into the RP75 and tighten snugly (see
Figure 1). DO NOT OVERTIGHTEN or threads may strip.
Attach and tighten outer cable securing nut. If installing the
chain, attach the “S” hook to the RP75 (see Figure 1).
2.
Attach the other end of the cable or chain to the injection pump
or air intake shut-off lever so it moves freely without sharp
bends and without binding.
Operation Test
NOTE: Some method must be provided to disconnect (lockout) all
normally closed SWICHGAGE®circuits when starting (such as
through the appropriate Magnetic Switch).
1.
Reset magnetic switch.
2.
Push in RP75 reset stem until coil latches the trip mechanism.
3.
Start engine and observe that all locked out contacts clear.
4.
With engine running, ground SWICHGAGE®contact. The
Magnetic Switch will trip thus removing voltage to RP75. The
engine should shutdown immediately. If the engine does shut-
down, adjust control linkage (cable or chain) to ensure that shut-
off lever travels the full length in both directions.
RP75
Magnetic Switch Energized to Run
SWICHGAGE®
CSBBattery
117PH
RP75
Magnetic Switch Energized to Run
SWICHGAGE®
GBSW1 SW2N.C. Battery
518PH
RP75
Time Delay On Start
SWICHGAGE®
GBSN.O. N.C. Battery
761APH
Installation Instructions
WARNING
Before beginning installation of this Murphy product:
✔✔Disconnect ALL electrical power to the machine.
✔✔Make sure the machine CANNOT operate during installation.
✔✔Follow all safety warnings of the machine manufacturer.
✔✔Read and follow all installation instructions.
Mounting
Bracket
Lockwashers
(4 required)
1/4-20 Nut
(4 required)
Wiring
Terminals
Cable
Attaching Nut
Outer Cable
Securing Nut
“S” Hook Chain
Reset Knob
and Stem
Push to Latch
Firewall
Reset
Knob
Mounting
Nut
Reset
Stem
Allenhead
Screw
Figure 1
Figure 2
Figure 3
CAUTION:Shut-off lever should not pull hard
against the stop in the “off” position.
WARNING:The
firewall must be capa-
ble of withstanding the
push and pull force of the RP75.
CONTROL SYSTEMS & SERVICES DIVISION
P.O. Box 1819
Rosenberg, Texas 77471 USA
Phone: +1 281 633 4500 Fax: +1 281 633 4588
E-mail: [email protected]
FRANK W. MURPHY, LTD
Church Rd Laverstock
Salisbury SP1 1QZ UK
Phone: +44 172 241 0055 Fax: +44 172 241 0088
E-mail: [email protected]
Web site: www.fwmurphy.co.uk
COMPUTRONIC CONTROLS, LTD
41 - 43 Railway Terrace Nechells
Birmingham B7 5NG UK
Phone: +44 121 327 8500 Fax: +44 121 327 8501
E-mail: [email protected]
Web site: www.computroniccontrols.com
FW MURPHY INSTRUMENTS (HANGZHOU) CO. LTD
77 23rd Street
Hangzhou Economic & Technological Development Area
Hangzhou, Zhejiang 310018 China
Phone: +86 571 8788 6060 Fax: +86 571 8684 8878
FW MURPHY
P.O. Box 470248
Tulsa, Oklahoma 74147 USA
+1 918 317 4100 Fax: +1 918 317 4266
E-mail: [email protected]
INDUSTRIAL PANEL DIVISION
Fax: +1 918 317 4124
E-mail: [email protected]
MURPHY POWER IGNITION
Web site: www.murphy-pi.com
www.
fwmurphy
.com Printed in U.S.A.
Table des matières
Autres manuels Murphy Pièce automobile
Murphy
Murphy MURPHYMATIC AT03069 Manuel utilisateur
Murphy
Murphy CNG-92200H Manuel utilisateur
Murphy
Murphy Diesel-Fuel Shutoff Valve SV-Series Manuel utilisateur
Murphy
Murphy MLA20 Manuel utilisateur
Murphy
Murphy EG-05012B Manuel utilisateur
Murphy
Murphy TAH-97026B Manuel utilisateur
Murphy
Murphy Selectronic MT90 Manuel utilisateur
Murphy
Murphy Gear Oil Pressure Sender EGPK-95083N Manuel utilisateur
Murphy
Murphy Digital Tach/Hourmeter with Overspeed Trip Point... Manuel utilisateur
Murphy
Murphy Exhaust Pyrometers 10705146 Manuel utilisateur
Murphy
Murphy M5081 Series Manuel utilisateur
Murphy
Murphy Digital Time Meters HD35-CD Manuel utilisateur
Murphy
Murphy Engine Panels WD300-LV Manuel utilisateur
Murphy
Murphy Diesel Fuel Check Valves CKV1WPS Manuel utilisateur
Murphy
Murphy Diagnostic Display PV10 Manuel utilisateur
Murphy
Murphy SELECTRONIC TACHSWICH DT9803 Manuel utilisateur
Murphy
Murphy Pull/Push DC Solenoids RP2307B Manuel utilisateur
Murphy
Murphy Lube Level Maintainer LM2000 Manuel utilisateur
Murphy
Murphy Selectronic DT9800 Manuel utilisateur
Murphy
Murphy Dump Valves DV Series Manuel utilisateur
