MULTIQUIP TP24X Mode d’emploi

OPERATION AND PARTS MANUAL

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

MODEL TP24X

TILE SAW

(ELECTRIC MOTOR)

Revision #4 (09/12/19)

To ﬁnd the latest revision of this

publication, visit our website at:

www.multiquip.com

PAGE 2 — TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19)

PROPOSITION 65 WARNING

TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19) — PAGE 3

Grinding/cutting/drilling of masonry, concrete, metal and

other materials with silica in their composition may give

off dust or mists containing crystalline silica. Silica is a

basic component of sand, quartz, brick clay, granite and

numerous other minerals and rocks. Repeated and/or

substantial inhalation of airborne crystalline silica can

cause serious or fatal respiratory diseases, including

silicosis.Inaddition, California and some other

authorities have listed respirable crystalline silica as a

substance known to cause cancer. When cutting such

materials, always follow the respiratory precautions

mentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and

other materials can generate dust, mists and fumes

containing chemicals known to cause serious or fatal

injury or illness, such as respiratory disease, cancer,

birth defects or other reproductive harm. If you are

unfamiliar with the risks associated with the particular

process and/or material being cut or the composition of

the tool being used, review the material safety data

sheet and/or consult your employer, the material

manufacturer/supplier, governmental agencies such as

OSHA and NIOSH and other sources on hazardous

materials. California and some other authorities, for

instance, have published lists of substances known to

cause cancer, reproductive toxicity,or other harmful

effects.

Control dust, mist and fumes at the source where

possible. In this regard use good work practices and

follow the recommendations of the manufacturers or

suppliers, OSHA/NIOSH, and occupational and trade

associations.Water should be used for dust

suppression when wet cutting is feasible. When the

hazards from inhalation of dust, mists and fumes cannot

be eliminated, the operator and any bystanders should

always wear a respirator approved by NIOSH/MSHA for

the materials being used.

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

SILICOSIS/RESPIRATORY WARNINGS

PAGE 4 — TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19)

TABLE OF CONTENTS

TP24X Tile Saw

Proposition 65 Warning ........................................... 2

Silicosis/Respiratory Warnings ................................ 3

Table Of Contents.................................................... 4

Safety Information ................................................ 6-9

Speciﬁcations ........................................................ 10

Dimensions............................................................ 11

General Information............................................... 12

Saw Components ............................................. 14-15

Electric Motor Components ................................... 16

Set-Up .............................................................. 16-20

Sawing Guides ................................................. 20-21

Operation.......................................................... 22-23

Maintenance..................................................... 24-30

Wiring Diagram (Electric Motor) ............................ 31

Troubleshooting (Blade)......................................... 32

Troubleshooting (Saw)........................................... 33

Explanation Of Code In Remarks Column............. 34

Suggested Spare Parts ......................................... 35

Main Saw Assy.................................................. 36-37

Cutting Head Assy. ........................................... 38-39

Cutting Table Assy............................................. 40-41

Blade Guard Assy............................................. 42-43

Bearing Housing Assy....................................... 44-45

Switch Box Assy................................................ 46-47

Tools And Accessories ..................................... 48-49

NOTICE

Speciﬁcations and part numbers are subject to change

without notice.

TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19) — PAGE 5

NOTES

PAGE 6 — TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19)

SAFETY INFORMATION

Do not operate or service the equipment before reading

the entire manual. Safety precautions should be followed

at all times when operating this equipment.

Failure to read and understand the safety

messages and operating instructions could

result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you

about potential hazards that could injure you or others.The

safety messages speciﬁcally address the level of exposure

to the operator and are preceded by one of four words:

DANGER, WARNING, CAUTION

or NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided,

COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided,

COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this

equipment will be referenced with hazard symbols which

may appear throughout this manual in conjunction with

safety messages.

Rotating parts hazards

Symbol Safety Hazard

Cutting and crushing hazards

Electric shock hazards

TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19) — PAGE 7

SAFETY INFORMATION

GENERAL SAFETY

WARNING



Adherence to the OSHA 2017 Ruling governing

Occupational Exposure to Respirable Crystalline Silica,

requires that all sawing operations MUST BE conducted

with an integrated water delivery system that feeds water

to the blade.

CAUTION



NEVER operate this equipment without proper protective

clothing, shatterproof glasses, respiratory protection,

hearing protection, steel-toed boots and other protective

devices required by the job or city and state regulations.



Avoid wearing jewelry or loose ﬁtting clothes that may

snag on the controls or moving parts as this can cause

serious injury.



NEVER operate this equipment when not

feeling well due to fatigue, illness or when

under medication.



NEVER operate this equipment under the

inﬂuence of drugs or alcohol.



ALWAYS clear the work area of any debris, tools, etc.

that would constitute a hazard while the equipment is

in operation.



No one other than the operator is to be in the working

area when the equipment is in operation.



ALWAYS check the equipment for loosened threads or

bolts before starting.



DO NOT use the equipment for any purpose other than

its intended purposes or applications.

NOTICE



This equipment should only be operated by trained and

qualiﬁed personnel 18 years of age and older.



Whenever necessary, replace nameplate, operation and

safety decals when they become difﬁcult read.



Manufacturer does not assume responsibility for any

accident due to equipment modiﬁcations. Unauthorized

equipment modiﬁcation will void all warranties.

NEVER

use accessories or attachments that are not

recommended by Multiquip for this equipment. Damage

to the equipment and/or injury to user may result.

ALWAYS know the location of the nearest

ﬁre extinguisher.

ALWAYS know the location of the nearest

ﬁrst aid kit.

ALWAYS know the location of the nearest phone or

keep

a phone on the job site.

Also, know the phone numbers

of the nearest ambulance, doctor and

ﬁre department.

This information will be invaluable in the case of an

emergency.

PAGE 8 — TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19)

SAFETY INFORMATION

SAW SAFETY

DANGER



NEVER operate the equipment in an explosive atmosphere

or near combustible materials. An explosion or ﬁre could

result causing severe bodily harm or even death.

WARNING



Accidental starting can cause severe injury

or death. ALWAYS place the ON/OFF

switch in the OFF position.



Keep hands away from moving parts at all

times.



NEVER disconnect any emergency

or safety devices. These devices are

intended for operator safety. Disconnection of these

devices can cause severe injury, bodily harm or even

death. Disconnection of any of these devices will void

all warranties.

CAUTION



ALWAYS ensure saw is securely placed on appropriate

blocks or jackstands when maintenance requires

elevation of the saw.



If the machine malfunctions, stop the saw immediately

and secure it. Fix the problem as soon as possible.

NOTICE



ALWAYS keep the machine in proper running condition.



Fix damage to machine and replace any broken parts

immediately.



Make sure there is no buildup of grease, oil or debris

on the machine.



ALWAYS store equipment properly when it is not being

used. Equipment should be stored in a clean, dry location

out of the reach of children and unauthorized personnel.

BLADE SAFETY

WARNING



Rotating blade can cut and crush. ALWAYS

keep hands and feet clear while operating

the saw.

CAUTION

NEVER operate the saw without blade

guards and covers in place. Exposure of

the diamond blade must not exceed 180

degrees.



Verify the motor start switch is set to the OFF position

before installing a blade.

ALWAYS inspect blade before each

use. The blade should exhibit no cracks,

dings, or ﬂaws in the steel centered core

and/or rim. Center (arbor) hole must be

undamaged and true.

NOTICE



Use proper blades and follow blade manufacturer’s

recommendations. Match the blade RPM (blade shaft

RPM) to the recommended blade surface feet per minute

(SFPM).



Ensure the blade-mounting bolt is tightened

adequately

ALWAYS

examine blade flanges for damage and

excessive wear.



Ensure the blade is marked with an operating speed

greater than the spindle speed of the saw.



Only cut the material that is speciﬁed for the diamond

blade. Read the speciﬁcation of the diamond blade to

ensure the proper tool has been matched to the material

being cut.



Ensure that water is used during sawing operations and

that a sufﬁcient ﬂow of water is applied to both sides of

the blade.

DO NOT

drop the diamond blade on ground or surface.



Ensure that the blade is mounted for proper operating

direction.



Adhere to the blade manufacturer’s recommendations

on handling, storage and safe usage of blades.

TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19) — PAGE 9

SAFETY INFORMATION

ELECTRIC MOTOR SAFETY

NOTICE



Operate electric motor only at the speciﬁed voltage

indicated on the nameplate.



DO NOT spray water onto electric motor.



ALWAYS disconnect AC power plug from power source

before moving saw, changing blade, or performing

maintenance.



ALWAYS make sure the ON/OFF switch

on the electric motor is in the OFF position

when not in use and before inserting the

saw’s power plug into an AC receptacle.

Power Cord/Cable Safety

DANGER



NEVER let power cords or cables lay in water.



NEVER use damaged or worn cables or cords when

connecting equipment to generator. Inspect for cuts in

the insulation.



NEVER grab or touch a live power

cord or cable with wet hands. The

possibility exists of electrical shock,

electrocution or death.



Make sure power cables are securely

connected. Incorrect connections may

cause electrical shock and damage to the

saw.

CAUTION



Ensure that cables and cords will not be tripped over or

trapped underneath the saw.



Never use the cable to pull out the plug from the power

source.

NOTICE



ALWAYS make certain that proper power or extension

cord has been selected for the job.



Protect the cable from heat, oil, and sharp edges.

LIFTING SAFETY

CAUTION

NEVER

allow any person or animal to stand underneath

the equipment while lifting.



Some saws are very heavy and awkward to move around.

Use proper heavy lifting procedures.

DO NOT lift machine to unnecessary heights.

NEVER lift the equipment while the motor is running.

TRANSPORTING SAFETY

NOTICE

ALWAYS shutdown motor before transporting.

ALWAYS

tie down equipment during transport by

securing the equipment with rope.



Ensure that the diamond blade does not come into contact

with the ground or surface during transportation.

NEVER

transport the saw to or from the job site with the

blade mounted.

ENVIRONMENTAL SAFETY

NOTICE

Dispose of hazardous waste properly.

Examples of potentially hazardous waste

are used motor oil, fuel and fuel ﬁlters.

DO NOT

use food or plastic containers to dispose of

hazardous waste.

DO NOT

pour waste, oil or fuel directly onto the ground,

down a drain or into any water source.

PAGE 10 — TP24X TILE SAW • OPERATION AND PARTS MANUAL — REV. #4 (09/12/19)

SPECIFICATIONS

Table 1. Saw Speciﬁcations

Model TP24X

Blade Capacity 10 in. (254 mm)

Blade RPM 3200

Arbor Size 5/8 in. (15.875 mm)

Blade Guard Cast Aluminum

Blade Shaft Bearings Water-Cooled

Cutting Head Cast Aluminum, Adjustable

Conveyor Cart Aluminum with roller bearings, injected

molded rubber pad, transportation lock

Drive System V-belt

Max. Depth of Cut 3-1/2 in. (90 mm)

Straight Cut 24 in. (610 mm)

Diagonal Cut 18 in. (457 mm) x 18 in. (457 mm) Size Tile

Water Tray ABS

Water Pump 115V, 60 Hz — 100 GPH

Weight 103 lbs. (46.7 kg)

Table 2. Electric Motor Speciﬁcations

Horsepower 1-1/2

Volts 115

Amps 15

Motor RPM 3450 RPM

Cycle 60

Phase 1

Class E

Table des matières

Autres manuels MULTIQUIP Scie

MULTIQUIP

MULTIQUIP CS706016 Manuel utilisateur

MULTIQUIP

MULTIQUIP Stow Cutter 3 CC813H20 Mode d’emploi

MULTIQUIP

MULTIQUIP SP113H18 Mode d’emploi

MULTIQUIP

MULTIQUIP MP1415E Mode d’emploi

MULTIQUIP

MULTIQUIP FCG1-6HA Mode d’emploi

MULTIQUIP

MULTIQUIP MP2050E1 Manuel utilisateur

MULTIQUIP

MULTIQUIP MP25E1 Manuel utilisateur

MULTIQUIP

MULTIQUIP MP1 Series Mode d’emploi

MULTIQUIP

MULTIQUIP PS706016 Manuel utilisateur

MULTIQUIP

MULTIQUIP SP118 Manuel utilisateur

MULTIQUIP

MULTIQUIP SP403030 Manuel utilisateur

MULTIQUIP

MULTIQUIP SP2S20H Manuel utilisateur

MULTIQUIP

MULTIQUIP MASON PRO MP1 Guide d'application

MULTIQUIP

MULTIQUIP StreetPro SP706016 Manuel utilisateur

MULTIQUIP

MULTIQUIP FCG1 SERIES Guide d'application

MULTIQUIP

MULTIQUIP TP24 Mode d’emploi

MULTIQUIP

MULTIQUIP FS2 Manuel utilisateur

MULTIQUIP

MULTIQUIP FS2 Manuel utilisateur

MULTIQUIP

MULTIQUIP tp7X Manuel utilisateur

MULTIQUIP

MULTIQUIP CD6CE13H18 Manuel utilisateur

MULTIQUIP

MULTIQUIP Diamond Back SP303516 Street Pro Mode d’emploi

MULTIQUIP

MULTIQUIP SP-6457 TD Manuel utilisateur

MULTIQUIP

MULTIQUIP FS 1 Manuel utilisateur

MULTIQUIP

MULTIQUIP StreetPro SP1E16A Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur