MTX TM652WB Manuel utilisateur
1
mtx.com/marine
TM652WB OWNERS MANUAL
2
Thank you for purchasing a MTX Marine product. MTX recommends that you have
your wakeboard speakers professionally installed. Please visit MTX.com to locate
the nearest authorized MTX dealer.
NOTE: Speaker does not ship assembled, please be careful not to lose any parts.
TOOLS REQUIRED:
• 10mm socket
• 3⁄8" drill bit
• 1⁄4" drill bit
• Cordless drill
• Speaker wire
• 3mm Allen wrench
• 5mm Allen wrench
• Wire cutter
mtx.com/marine 3
WARNING!
Loud Music can cause permanent damage to your hearing. Please listen to your
system at moderate volume levels.
Mitek does not accept any liability for bodily harm, property damage, or any
consequential damages resulting from the design, manufacture, sale or use of
this product.
Rubber inserts are numbered 1, 2, and 3. Insert #1 is the thickest and insert #3 is
the thinnest.
*Use double sided automotive grade tape under the rubber inserts on pipe if
needed.
WARNING STATEMENT:
PIPE DIAMETER INSERT GUIDE:
Pipe Diameter (in) Bracket Insert # Enclosure Insert #
*2.375 (23⁄8)11
2.5 (21⁄2)11
2.625 (25⁄8)12
2.75 (23⁄4)22
*2.875 (27⁄8)23
333
4
INSTALLATION:
Step 1 – First determine where you would like to
place the speaker and at what angle the speaker
will be mounted. Place enclosure on bar with
desired angle and make a mark in the middle of
the wire hole on the bar. This mark will be where
the speaker wire will come thru the bar into the
enclosure.
Step 2 – Drill a 3⁄8" hole for the speaker wire on the
mark that you made. Deburr the hole to keep from
damaging the speaker wire. Treat the hole with a
paint or sealer to inhibit corrosion.
Step 3 – Connect the safety tether
Drill out safety tether hole using a 1⁄4" drill bit on
enclosure depending on which side you would like
to mount the tether. Loop safety tether around Bar.
Next place tether bolt through tether ring and
rubber washer. Then put bolt through drilled hole
on enclosure and secure with metal washer and
locknut. Let enclosure hang by tether until next step.
mtx.com/marine 5
Step 4 – Run speaker wire thru the bar and leave
8" – 12" of speaker wire hanging out of the hole.
Next place rubber inserts into the enclosure and
bracket. Please select the correct insert size
according to the insert selection guide on page 3.
Place round foam gaskets on to bracket standoffs.
Place enclosure in desired location and pull wire
through wire hole. Place top bracket on top of the
bar above the enclosure. Start to thread the bracket
screws into bracket from inside the enclosure.
Tighten front and back screws evenly, make sure to
tighten until bracket holds tight and the enclosure
does not move.
Step 5 – Connect speaker wire to the input on the
speaker, making sure to keep the polarity correct.
Place woofer into the enclosure with the badge
closest to the top. Make sure to tuck the wires
into the enclosure so they do not get caught in the
opening. Screw in the 4 speaker bolts, make sure to
tighten the bolts fully.
NOTE: If bolts are removed after installation,
threadlock must be re-applied.
Step 6 – Connect speaker wire to amplifier, place
boat in water, crank the THUNDER and enjoy.
6
OVERALL ASSEMBLY:
mtx.com/marine 7
NOTES:
MTX WARRANTY STATEMENT:
MTX products purchased in the USA from an authorized MTX dealer are
guaranteed against defects in material and workmanship for the period of 1 year.
The warranty period begins the day the product is purchased by the end user. This
warranty is limited to the original retail purchaser of product. Product found to
be defective during that period will be repaired or replaced by MTX at no charge.
This warranty is void if it is determined that unauthorized parties have attempted
repairs or alterations of any nature. Warranty does not extend to cosmetics or
finish. Before presuming a defect is present in the product, be certain that all
related equipment and wiring is functioning properly. MTX disclaims any liability
for other incurred damages resulting from product defects. Any expenses in the
removal and reinstallation of products are not covered by this warranty. MTX’s
total liability will not exceed the purchase price of the product. If a defect is
present, your authorized MTX dealer may be able to effect repairs.
Proof of purchase is required when requesting service, so please retain your sales
receipt, and take a moment to register your product online at MTX.com. Also, a
Return Authorization number (RA) is required before shipping product back to MTX,
call 800-556-2888 or 608-328-5560, for speaker RAs.
8
© 2010 Mitek Corporation. All rights reserved. MTX and Thunder Marine are trademarks of Mitek Corporation.
Designed and Engineered in the U.S.A.
Due to continual product development, all specifications are subject to change without notice.
MTX Audio, 1 Mitek Plaza, Winslow, IL 61089 U.S.A.
MTX003848 RevA 7/10 21A9546 AW0013756
Autres manuels pour TM652WB
1
Table des matières
Autres manuels MTX Intervenants
MTX
MTX iP3 Manuel utilisateur
MTX
MTX Thunder Dome-Axials TDX3502 Manuel utilisateur
MTX
MTX Blueprint 502W Manuel utilisateur
MTX
MTX MUD65PL Manuel utilisateur
MTX
MTX Thunder AXE TX6001 Mode d’emploi
MTX
MTX H620C Manuel
MTX
MTX Blueprint 520W Manuel utilisateur
MTX
MTX Blueprint 620WE Manuel utilisateur
MTX
MTX RoadThunder RT12-04 Manuel utilisateur
MTX
MTX Thunder AXE TXC-1 Manuel utilisateur
MTX
MTX MP42B/ MP42W Manuel utilisateur
MTX
MTX Blueprint 510CM Manuel utilisateur
MTX
MTX AW52 Manuel utilisateur
MTX
MTX MUSICA SERIES Manuel utilisateur
MTX
MTX AAL10 Manuel utilisateur
MTX
MTX X3-17-FS-L Manuel utilisateur
MTX
MTX MONITOR5i Manuel utilisateur
MTX
MTX CD620W Manuel
MTX
MTX Thunder AXE TX1000 Mode d’emploi
MTX
MTX Blueprint H615W Manuel utilisateur
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur