MSTRONIC PSE-SW8 series Manuel utilisateur
PSE-SW8 series
8 Port PoE Switch (Endspan)
(Extend Ethernet and PoE)
USER’S MANUAL
MSTRONIC CO., LTD.
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
2
1. General Information..............................................................
2. Hardware Description...........................................................
LED Indicators.......................................................................................
Power Wiring ........................................................................................
Ethernet Port/PD Port Wiring………………………………………………
3. Network Application…………………………………………….
4. Model Information.................................................................
5. echnical Specification.........................................................
3
3
3
5
6
8
9
10
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
3
1. General Information
The PSE-SW8 PoE Switch family provides a PoE/Data input port that is compatible with 80 .3af
and 80 .3at (Type 1 and Type ) and it has seven 10M/100M TX ports with PoE PSE function. In
addition to the ability to accept 48VDC PoE input on Port 8, the model provides secondary DC wire
terminal input for PoE switch operation from 1 V to 57VDC. If powered the model via rear DC
terminal, the PoE output voltage is equal to the input voltage. The PoE Switch can be used as an
Ethernet/PoE repeater to extend Ethernet data and DC power up to 00 meters.
This manual will
help you install and maintain the PoE switch. Installation of the PoE switch is very easy and you
will begin to operate as soon as you are powered up.
The PSE-SW8 comes with DIN rail mounting clips for ease of mounting in network cabinets.
2. Hardware Description
*LED Indicator
There are 18 LEDs on the PoE switch to indicate the power and operational status. The following
section describes the functions of each LED indicator.
Front panel detail
the port number is as the diagram shows.
5 6 7 8
1 3 4
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
4
*PWR Indicator
LED
STATUS
Description
Power
Green
LED ON if power input has valid power
supplied. (via the terminal block on rear
panel or Port 8 on front panel)
Red
LED ON if the following condition
happens.
*Power input under voltage (Vin<1 V)
*Power input over voltage (Vin>58V)
*PoE over current( A)
The indicator is unused on PSE-SW8D
Off No power in DC input
*SWITCH indicator (the right LED on RJ45)
LED STATUS Description
P1~P8
Link/Act
Green
A network device is detected at 100Mbps,
but no communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving
package from another device at 100Mbps.
Yellow A network device is detected at 10Mbps,
but no communication activity is detected.
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 10Mbps.
Off No device is detected.
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
5
*PoE indicator (the left LED on RJ45)
LED STATUS Description
P1~P7
PoE PSE
Yellow
LED ON when PoE power output.
Off No PoE output
P8
PoE PD
Yellow
PSE-SW8D:4 pairs power source receive.
PSE-SW8S: or 4 pairs power source receive.
Yellow
Blinking
PSE-SW8D: pairs power source receive.
PSE-SW8S:unused.
Off No power is detected on this port.
*Power wiring
The PoE switch accepts input voltage from terminal block P3 or DIN 4P connector (rear panel) or
RJ45 (port 8).
For PSE-SW8S,
If power input from terminal block P3, the input voltage must be in the range of 1 to 57 VDC. The
output current is 1A/port (continuously), it can up to A/port maximum for temporary, but total
output power MUST limited at 7A maximum. If power input from port 8, the input current is
limited at A maximum, the output is 0. 5A/port.
For PSE-SW8D
The input voltage must be in the range of 44 to 57VDC if running for 80 .3af operation or 50 to
57VDC if running for 80 .3at operation. If the model is not powered within designated voltage, it
will only function as an Ethernet switch without PoE output.
If power input from terminal block P3, and if output power to 80 .3af devices, the output current is
0.35A/port, if output power to 80 .3at devices, the output power is 0.6 5A/port maximum.
If power input from port 8, the input current is limited at A maximum, the output is 0. 5A/port.
The PoE PSE ports (port 1-7) will deliver DC power over the spare pairs as the connection:
* TX on lines 1 and
* RX on lines 3 and 6
* V+ on line 4 and 5
* V- on line 7 and 8
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
6
The Port 8 may get power over the signal pair or spare pairs, the connection as:
* Data pair A plus V+ /V- on lines 1 and
* Data pair B plus V-/V+ on lines 3 and 6
* V+/V- on line 4 and 5
* V-/V+ on line 7 and 8
The terminal block on the rear panel should be wired as detailed below:
The DIN-4P connector on the rear panel also used for power input, you can use an AC/DC adapter
with DIN-4P connector directly, recommends adaptor as detailed below: (OPTION)
MS-180-18 MS-180- 4 MS-180-56
Maximum output 18VDC/8.33A 4VDC/6. 5A 56VDC/3. 1A
Related model PSE-SW8S PSE-SW8S PSE-SW8S
PSE-SW8D
*Ethernet Port/PD Port Wiring
The PoE Switch supports Port 1 to Port 8 with automatic MDI/MDI-X crossover, autosense of the
speed and duplex for 10Base-T or 100Base-TX connections. Automatic MDI/MDI-X crossover
allows you to connect to other devices (switches, hubs, or workstations etc.), without regard to
using straight-through or crossover cabling.
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
7
Port 1 to port 7 also provides PSE function which delivers DC power through the spare pairs (pair
4,5 and pair7,8) to the PD. Port 8 provides PD function that receive power from 4 pairs or pairs
Ethernet cable.
The following tables depict the wiring diagram of straight-through and crossover cabling. The
crossover cables simply cross-connect the transmit lines at each end to the receive lines at the
opposite end.
Straight-through Cabling
Pin 1 Pin 1
Pin Pin
Pin 3 Pin 3
Pin 6 Pin 6
Cross-over Cabling
Pin 1 Pin 3
Pin Pin 6
Pin 3 Pin 1
Pin 6 Pin
Connect an Ethernet cable into any switch port and connect the other side to your attached device.
The green or yellow Link/Act LED will light up when the cable is correctly connected. Refer to the
LED Indicator section for descriptions of each LED indicator.
If a port LED is off, go back and check for connectivity problems between that port and the network
device it is connected to.
The maximum cable length for 10/100BaseT with Cat 5 twisted pair cables is typically 100 meters
(3 8 ft.).
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
8
3. Network Application
The PoE Switch can receive power from PoE midspan and provide power to the PD. It will power
80 .3af compliant devices if it is powered at 48VDC although it will not perform the 80 .3af
handshake with the client device. The PoE Switch can be installed in a more appropriate position
for better performance to extend Ethernet to 00 meters. The following figure is an example of a
network application for PoE Switch.
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
9
4. Model Information
Model Input Voltage
(REAR)
Input Voltage
(Port 8) Output voltage
PSE-SW8S
1 -57VDC No input
1 -57VDC
(As input voltage)
(non-regulated)
(non-80 .3at compliant)
No input 1 -57VDC
1 -57VDC
(As input voltage)
(non-regulated)
(non-80 .3at compliant)
1 -57VDC 1 -57VDC
Higher input voltage
(As input voltage)
(non-regulated)
(non-80 .3at compliant)
PSE-SW8D
44-57VDC No input
44-57VDC
(As input voltage)
(non-regulated)
(80 .3at compliant)
No input 44-57VDC
44-57VDC
(As input voltage)
(non-regulated)
(80 .3at compliant)
44-57VDC 44-57VDC
Higher input voltage
(As input voltage)
(non-regulated)
(80 .3at compliant)
MS-180-18 MS-180- 4 MS-180-56
Maximum output 18VDC/8.33A 4VDC/6. 5A 56VDC/3. 1A
Related model PSE-SW8S PSE-SW8S PSE-SW8S
PSE-SW8D
User’s Manual
MSE PSE-SW8 Series
MSTRONIC CO., LTD.
10
5. echnical Specifications
Standards IEEE80 .3/IEEE80 .3u standards (10 base-T/100base-T)
Ports 8 ports with 7 PoE PSE & 1 PoE PD, supports auto-crossover &
auto-polarity
Transmission speed 100 Mbps(100base-T),10 Mbps(10base-T) Auto-negotiation
Switch technology store-and-forward
Protocols CSMA/CD
Flow control IEEE80 .3x(full-duplex),back pressure(half-duplex)
Data transmission rate 148800pps for 100base-T, 14880pps for 10base-T
Address table K MAC address table, self-learning
Connect RJ-45
PoE port Port 1-7, Pin assignment: TX(1, ), RX(3,6), V+(4,5), V-(7,8)
Port 8, 4 pairs PD
Maximum PoE power Port 1-7: IEEE80 .3af –16.8W (0.35A/port)
IEEE80 .3at—35W (0.6 5A/port)
A/port , total 7A Maximum (PSE-SW8S)
Port 8: 90W (80 .3at event classification)
PoE disconnect mode DC disconnect
PoE auto detection IEEE80 .3af and IEEE80 .3at( event classification)
PoE protection Over-current, over/under voltage
Autres manuels pour PSE-SW8 series
1
Table des matières
Autres manuels MSTRONIC Changer
MSTRONIC
MSTRONIC MSE PSE-SW3G Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW5G25B4-IP66 Manuel utilisateur
MSTRONIC
MSTRONIC MSE PSE-SSW5 Series Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW8G44D0++ Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW5G15B4HM Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW5G-25 4 Series Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW5B44DB Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW5B15DBHM-IP66 Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW5G-25B4HM Manuel utilisateur
MSTRONIC
MSTRONIC PSE-SW8G44A4 Manuel utilisateur
