MPL mSERLED Manuel utilisateur
µSERLED User Manual
The µSERLED is a LED Panel used on various MPL network products. It converts the serial stream into signals
to control 6 dual color LEDs. Additional 2 Buttons are implemented which may be used as Reset and Default
Button.
This Manual is written for Users of an MPL Network Device as Open Frame, whereas the µSERLED is
optional.
●Features:
●Deserialization of 6 Dual color LEDs.
●Up to 8 different mappings selectable with DIP
switch
●Two push-Buttons
●Small footprint (24 x 56 x 8.6mm)
●7 Pin Connector.
2022 by MPL AG MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
TABLE OF CONTENTS
1 INTRODUCTION............................................................................................................ 5
1.1 ABOUT THIS MANUAL........................................................................................................5
1.2 SAFET PRECAUTIONS AND HANDLING.........................................................................5
1.3 ELECTROSTATIC DISCHARGE (ESD) PROTECTION.......................................................5
1.4 EQUIPMENT SAFET .......................................................................................................... 5
1.5 MANUAL REVISIONS........................................................................................................... 6
.5. RELATED PRODUCTS.................................................................................................6
.5.2 REVISION HISTORY....................................................................................................6
1.6 RELATED DOCUMENTATION.............................................................................................7
1.7 STANDARDS COMPLIANCE...............................................................................................8
.7. EMC.............................................................................................................................. 8
.7.2 ENVIRONMENTAL........................................................................................................ 8
.7.3 SAFETY.........................................................................................................................8
.7.4 TYPE APPROVAL......................................................................................................... 8
1.8 ORDERING INFORMATION................................................................................................. 9
2 DIMENSIONS...............................................................................................................10
2.1 Top View............................................................................................................................. 10
2.2 Side view............................................................................................................................ 10
3 PARTS LOCATION......................................................................................................11
4 CONFIGURATIONS.....................................................................................................11
4.1 µMAGBES........................................................................................................................... 11
4. . µMAGBES-A 0OH / µMAGBES-A 0OR ( 0 Port Open Frame µMAGBES)...............
4. .2 µMAGBES-x 9OH / µMAGBES-x 9OR ( 9 Port Open Frame µMAGBES)................ 2
4. .2. Master µMAGBES-x 9OH................................................................................................... 2
4. .2.2 Slave µMAGBES-x 9OH..................................................................................................... 2
4. .3 µMAGBES-x8OH......................................................................................................... 2
4. .4 µMAGBES-x 4OH....................................................................................................... 3
4. .4. Master µMAGBES-x 4OH................................................................................................... 3
4. .4.2 Slave µMAGBES-x 4OH..................................................................................................... 3
4.2 µGUARD............................................................................................................................. 14
4.2. µGUARD-A3OH / µGUARD-A3OR (3 Port Open Frame µGUARD)............................ 4
4.2.2 µGUARD-A 2OH / µGUARD-A 2OR ( 2 Port Open Frame µGUARD)...................... 4
4.2.2. Master µGUARD.................................................................................................................. 4
4.2.2.2 Slave µMAGBES.................................................................................................................. 4
4.3 µMAXBES........................................................................................................................... 15
4.3. µMAXBES-A 0OH ( 0 Port Open Frame µMAXBES)................................................. 5
5 CONNECTORS............................................................................................................16
5.1 J1 Factory use only........................................................................................................... 16
5.2 J7 LED Panel Connector................................................................................................... 16
6 COP RIGHT................................................................................................................20
7 DISCLAIMER...............................................................................................................20
8 TRADEMARKS............................................................................................................20
9 SUPPORT....................................................................................................................20
2022 by MPL AG 2 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
TABLE OF FIGURES
Figure : µSERLED Top view Dimensions.......................................................................................................... 0
Figure 2: µSERLED Side view Dimensions......................................................................................................... 0
Figure 3: µSERLED Parts Location.....................................................................................................................
2022 by MPL AG 4 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
1 INTRODUCTION
1.1 ABOUT THIS MANUAL
This manual, and the MPL Network Product (i.e. µMAGBES, µGUARD) User Manual provides all the
information necessary to handle and configure the µSERLED.
The manual is written for technical personnel responsible for integrating the µSERLED into their systems.
It is strongly recommended to read the MPL Network Product (i.e. µMAGBES, µGUARD) User
Manual and also this manual before the µSERLED is switched on.
1.2 SAFET PRECAUTIONS AND HANDLING
For personal safety and safe operation of the µSERLED, follow all safety procedures described here and in
other sections of the miscellaneous manual.
●Remove power from the system before installing (or removing) the µSERLED, to prevent the possibility of
personal injury (electrical shock) and / or damage to the product.
●Handle the product carefully; i.e. dropping or mishandling the µSERLED can cause damage to assemblies
and components.
●Do not expose the equipment to moisture.
WARNING
There are no user-serviceable components on the µSERLED.
1.3 ELECTROSTATIC DISCHARGE (ESD) PROTECTION
Various electrical components within the product are sensitive to static and electrostatic discharge (ESD). Even
a small static discharge can be sufficient to destroy or degrade a component's operation!
With an open housing, do not touch any electronic components. Handle or touch only the unit chassis.
1.4 EQUIPMENT SAFET
Great care is taken by MPL AG that all its products are thoroughly and rigorously tested before leaving the
factory to ensure that they are fully operational and conform to specification. However, no matter how reliable a
product, there is always the remote possibility that a defect may occur. The occurrence of a defect on this
device may, under certain conditions, cause a defect to occur in adjoining and/or connected equipment. It is
your responsibility to protect such equipment when installing this device. MPL accepts no responsibility
whatsoever for such defects, however caused.
2022 by MPL AG 5 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
1.5 MANUAL REVISIONS
1.5.1 RELATED PRODUCTS
Manual
Revisions
Related To
A•µSERLED- Rev. A & Rev. B
B•µSERLED- Rev. C or Rev.B with TU MEW- 0226-00 -A
C•µSERLED- Rev. D or any Revision with TU MEW- 0226-002-A
1.5.2 REVISION HISTOR
Manual
Revisions
Date Description
A 202 -08-25 Initial release of this document. Moved from µMAGBES & µGUARD Manual
B 2022-04- 3 Added configuration for µMAGBES-A8OH
C 2022- 0-24 Added configuration for µMAGBES-A 4OH (master & slave)
2022 by MPL AG 6 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
1.6 RELATED DOCUMENTATION
The following documents are related to this manual. For detailed Information about a specific xxx feature or
setting please refer to this additional manuals.
Reference Description Available from
[ ] µMAGBES User Manual MPL AG: www.mpl.ch
[2] µGUARD User Manual MPL AG: www.mpl.ch
[3] µMAXBES User Manual MPL AG: www.mpl.ch
2022 by MPL AG 7 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
1.7 STANDARDS COMPLIANCE
The µSERLED is designed to meet or exceed the most common industry and military standards. Particular
references are:
1.7.1 EMC
•EN 55022 Class B (Information technology equipment - Radio disturbance characteristics - Limits and
methods of measurement)
•EN 55024 (Information technology equipment - Immunity characteristics - Limits and methods of
measurement)
•EN 6 000-4- (Electromagnetic compatibility (EMC) -- Part 4- : Testing and measurement techniques -
Overview of IEC 6 000-4 series)
•EN 6 000-4-2 Level 3, Criterion B (Electromagnetic compatibility (EMC) -- Part 4-2: Testing and
measurement techniques - Electrostatic discharge immunity test)
•EN 6 000-4-3 Level 3, Criterion A (Electromagnetic compatibility (EMC) -- Part 4-3: Testing and
measurement techniques - Radiated, radio-frequency, electromagnetic field immunity
test)
•EN 6 000-4-4 Class 3 (Electromagnetic compatibility (EMC) -- Part 4-4: Testing and measurement
techniques - Electrical fast transient/burst immunity test)
•EN 6 000-4-5 Class 3 (Electromagnetic compatibility (EMC) -- Part 4-5: Testing and measurement
techniques - Surge immunity test)
•EN 6 000-4-6 Class 3 (Electromagnetic compatibility (EMC) -- Part 4-6: Testing and measurement
techniques - Immunity to conducted disturbances, induced by radio-frequency fields)
•EN 6 000-6- (Electromagnetic compatibility (EMC) -- Part 6- : Generic standards - Immunity for
residential, commercial and light-industrial environments)
•EN 6 000-6-2 (Electromagnetic compatibility (EMC) -- Part 6-2: Generic standards - Immunity for industrial
environments)
•EN 6 000-6-3 (Electromagnetic compatibility (EMC) -- Part 6-3: Generic standards - Emission standard for
residential, commercial and light-industrial environments)
•EN 6 000-6-4 (Electromagnetic compatibility (EMC) -- Part 6-4: Generic standards - Emission standard for
industrial environments)
•MIL-STD-46 E (REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC INTERFERENCE
CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT)
1.7.2 ENVIRONMENTAL
•EN 50 55 (Railway applications - Electronic equipment used on rolling stock)
•MIL-STD-8 0-F (ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS)
1.7.3 SAFET
•EN 6060 - (Medical electrical equipment -- Part : General requirements for safety)
•EN 62368 (Audio/video, information and communication technology equipment)
1.7.4 T PE APPROVAL
•EN 60945 Protected Equipment (Maritime navigation and radiocommunication equipment and systems -
General requirements - Methods of testing and required test results)
•E 0 (Test Specification for Type Approval)
2022 by MPL AG 8 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
1.8 ORDERING INFORMATION
The table below gives you an overview of the different xxx variants and its features.
Product Name Product Features
µSERLED- •µSERLED with 6 dual Color LEDs and 2 Push Button. Without Lightpipes
•
2022 by MPL AG 9 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
2 Dimensions
2.1 Top View
2.2 Side view
Recommended Panel Holes for Switches Ø 2.6mm for LEDs Ø 3. mm
2022 by MPL AG 0 MEH- 0203-00 Rev. C
High-Tech • Made in Switzerland
µSERLED
User Manual
O
N
2
O
N
2
56.0
24.0
3.5
0
6.5
9.0
4.0
6.5
9.0
2 .5
24.0
26.5
29.0
3 .5
34.0
36.5
39.0
4 .5
44.0
46.5
49.0
5 .5
52.5
7.5
Ø2.7
6.0
2 .0
Figure 1: µSERLED Top view Dimensions
.6
3.5
7.0
2.7
6.4
Lightpipe, only one of
6 pcs shown
Ø2.5 Ø3.0
Figure 2: µSERLED Side view Dimensions
Table des matières
Autres manuels MPL Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
