Moxa Technologies NPort 5210 Manuel utilisateur

– 1 – – 2 – – 3 –

P/N: 1802052000311

NPort 5200 Series

Quick Installation Guide

Sixth Edition, March 2012

1. Overview

The NPort 5200 Series of compact palm-sized device servers are

used to control RS-232 (NPort 5210/5230/5210-T/5230-T) or

RS-422/485 (NPort 5230/5232/5232I/5230-T/5232-T/5232I-T)

serial devices over a TCP/IP-based Ethernet.

Note:

“-T” indicates an extended temperature model.

2. Package Checklist

Before installing NPort 5200, verify that the package contains the

following items:

•1 NPort 5200 2-port Serial Device Server

•Documentation & Software CD

•NPort 5200 Series Quick Installation Guide

Optional Accessories

•DK-35A

DIN-Rail Mounting Kit (35 mm)

•CBL-RJ45M9-150

RJ45 (8-pin) to DB9 (M) cable, 150 cm

•CBL-RJ45F9-150

RJ45 (8-pin) to DB9 (F) cable, 150 cm

•CBL-RJ45M25-150

RJ45 (8-pin) to DB25 (M) cable, 150 cm

•CBL-RJ45F25-150

RJ45 (8-pin) to DB25 (F) cable, 150 cm

•DIN-Rail Power Supply and Adapter

Notify your sales representative if any of the above items is

missing or damaged.

3. Hardware Introduction

The NPort 5200 series of device servers are used to control

RS-232/422/485 devices. NPort 5210/5210-T has two 8-pin RJ45

ports, both for the RS-232 interface. NPort 5230/5230-T has one

10-pin terminal block, with 5 pins used for one RS-232 port, and 5

pins used for one RS-422/485 port. NPort

5232/5232I/5232-T/5232I-T have one 10-pin terminal block, with

5 pins used for one RS-422/485 port, and 5 pins used for another

RS-422/485 port.

Reset Button—Press the Reset button continuously for 5 sec to

load factory defaults: Use a pointed object, such as a straightened

paper clip or toothpick, to press the reset button. This will cause

the Ready LED to blink on and off. The factory defaults will be

loaded once the Ready LED stops blinking (after about 5 seconds).

At this point, you should release the reset button.

NPort 5200 LED Indicators (top panel)

LED

Name

LED

Color

LED Function

Ready

red

Steady on:

Power is on and NPort 5200 is

booting up.

Blinking:

Indicates an IP conflict, or DHCP

or BOOTP server did n

ot respond

properly.

green

Steady on:

Power is on and NPort 5200 is

functioning normally.

Blinking:

The device server has been

located by Administrator’s

Location function

off

Power is off, or power error condition exists.

Ethernet

orange

10 Mbps Ethernet connection.

green

100 Mbps Ethernet connection.

off

Ethernet cable is disconnected, or has a

short.

P1, P2

orange

Serial port is receiving data.

green

Serial port is transmitting data.

off No data is being transmitted or received

through the serial port.

4. Hardware Installation Procedure

STEP 1: After removing NPort 5200 from the box, the first thing

you should do is connect the power adaptor. Connect the 12-30

VDC power line with NPort 5200’s terminal block, or connect the

DIN-Rail power supply with NPort 5200’s terminal block.

STEP 2: Connect NPort 5200 to a network. Use a standard

straight-through Ethernet cable to connect to a Hub or Switch.

When setting up or testing NPort 5200, you might find it

convenient to connect directly to your computer’s Ethernet port. In

this case, use a cross-over Ethernet cable.

STEP 3: Connect NPort 5200’s serial port to a serial device.

STEP 4: Placement Options

In addition to placing

NPort 5200 on a desktop

or other horizontal

surface, you may also

make use of the DIN

Rail

or Wall Mount options, as

illustrated here.

Wall Mount

DIN-Rail

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas: +1-714-528-6777 (toll-free: 1-888-669-2872)

Europe: +49-89-3 70 03 99-0

Asia-Pacific: +886-2-8919-1230

China: +86-21-5258-9955 (toll-free: 800-820-5036)

5. Software Installation Information

To install NPort Administration Suite, insert the NPort

Document & Software CD into your computer’s CD-ROM drive.

Once the NPort Installation CD window opens, click on the

Installation button, and then follow the instructions on the screen.

To view detailed information about NPort 5200 Administration

Suite, click on the Documents button, and then select “NPort

5200 Series User’s Guide” to open the pdf version of this user’s

guide. The PComm Lite program is also included in the

Documentation & Software CD free of charge. Install PComm

Lite to use the Serial Console for configuring the IP address for

the first time.

6. Pin Assignments and Cable Wiring—

NPort 5230/5230-T

Terminal Block Wiring

Note:

NPort 5232/5232I/5232-T/5232I-T have 2 RS-422/485 ports. The

pin assignments are the same as NPort 5230/5230-T’s port 2.

Refer to the “NPort 5200 Series User’s Manual” for more details.

7. Pin Assignments and Cable Wiring—

NPort 5210/5210-T

RJ45 (8-pin) Connector Pinouts

8-Pin Signal

1 DSR

2 RTS

3 GND

4 TxD

5 RxD

6 DCD

7 CTS

8 DTR

Cable Wiring (RS-232)

Four cables are available as optional accessories that can be used

to connect NPort 5210/5210-T to RS-232 serial devices. For your

convenience, we show precise cable wiring diagrams for each of

the four cables.

RJ45 (8-pin) to DB25 Female (Cable Name: CBL-RJ45F25-150)

RJ45 (8-pin) to DB25 Male (Cable Name: CBL-RJ45M25-150)

RJ45 (8-pin) to DB9 Female (Cable Name: CBL-RJ45F9-150)

RJ45 (8-pin) to DB9 Male (Cable Name: CBL-RJ45M9-150)

8. Specifications

Power requirements

NPort 5210/5210-T: 12 to 48 VDC, 325 mA at 12V (max.)

NPort 5230/5230-T: 12 to 48 VDC, 325 mA at 12V (max.)

NPort 5232/5232-T: 12 to 48 VDC, 280 mA at 12V (max.)

NPort 5232I/5232I-T: 12 to 48 VDC, 365 mA at 12 V (max.)

Operating temp.

For standard models

For -T models

0 to 55◦C (32 to 131◦F)

-40 to 75◦C (-40 to 167◦F)

Operating humidity 5 to 95% RH

Dimensions (W×D×H)

NPort 5210/5230/5232/

5210-T/5230-T/5232-T

(including ears)

90 × 100.4 × 22 mm

(3.54 × 3.95 × 0.87 in)

NPort 5210/5230/5232/

5210-T/5230-T/5232-T

(without ears)

67 × 100.4 × 22 mm

(2.64 × 3.95 × 0.87 in)

NPort 5232I/5232I-T

(including ears)

90 × 100.4 × 35 mm

(3.54 × 3.95 ×1.37 in)

NPort 5232I/5232I-T

(without ears)

67 × 100.4 × 35 mm

(2.64 × 3.95 × 1.37 in)

Surge protection 15 KV ESD for serial port

Magnetic isolation 1.5 KV for Ethernet

Power line protection 4 KV Burst (EFT), EN61000-4-4

2 KV Surge, EN61000-4-5

Regulatory approvals FCC Class A, CE Class A, UL, CUL, TÜV

Autres manuels pour NPort 5210

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Serveur

Moxa Technologies

Moxa Technologies NPort W2150 Plus Manuel utilisateur

Moxa Technologies

Moxa Technologies 6150 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5610-8-DT Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 6450 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5200 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2610 series Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2610 series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5130 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5100 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort W2150A Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA5150 series Manuel utilisateur

Moxa Technologies

Moxa Technologies VPort 2310 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA5150A Manuel utilisateur

Moxa Technologies

Moxa Technologies ioLogik R2110 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5610-16 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5110 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort W2250A-T-EU Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 6450 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA-5150-M-SC Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort S8455I Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5210-T Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5210A Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5000AI-M12 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur