Moxa Technologies NPort 5130 Manuel utilisateur

P/N: 1802051000014

*1802051000014*

NPort 5100 Series

Quick Installation Guide

Edition 4.2, November 2018

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

NPort 5100 series of device servers are compact, palm-sized data

communication devices that allow you to control RS-232 (NPort 5110),

RS-422/485 (NPort 5130), and RS-232/422/485 (NPort 5150) serial

devices over a TCP/IP-based Ethernet.

NOTE

“-T” indicates an extended temperature model.

Package Checklist

Before installing the NPort 5100 series of device servers, verify that the

package contains the following items:

•1 NPort 5100 Series 1-port serial device server

•100 to 240 VAC power adapter (excluding T models)

•4 stick-on pads

•Quick Installation Guide

•Warranty card

Optional Accessories

•DK-35A: DIN-Rail Mounting Kit (35 mm)

NOTE

otify your sales representative if any of the above items are

missing or damaged.

NOTE

The operating temperature of the power adapter in the box is

from 0 to 40°C. If your application is out of this range, please

use a power adapter supplied by UL

Listed External Power

Supply (The power output meets SELV and LPS and rated 12

48 VDC, minimum current 0.73 A). Moxa has power adapters

with wide temperature range (

-40 to 75°C, -40 to 167°F), the

PWR-12150-(plug type)-SA-T series, for your reference.

- 3 -

Hardware Introduction

As shown in the following figures, NPort 5100 series of device servers

have one male DB9 port for transmitting RS-232 (NPort 5110), RS-

422/485 (NPort 5130), or RS-232/422/485 (NPort 5150) serial data.

NOTE

The NPort 5110, NPort 5130, and NPort 5150 have the same

form factor.

Reset Button—Press the Reset button continuously for 5 sec to load

factory defaults: Use a pointed object, such as a straightened paper clip

or toothpick, to press the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, you should release

the reset button.

- 4 -

LED Indicators—NPort 5100’s top panel has three LED indicators,

which are described in the following table.

LED Name

LED Color

LED Function

Ready

Red

Steady on: Power is on and NPort is booting

up.

Blinking: Indicates an IP conflict, or DHCP or

BOOTP server is not responding properly.

Green

Steady on: Power is on and NPort is functioning

normally.

Blinking: The NPort has been located by NPort

Administrator’s Location function

Off

Power is off, or power error condition exists.

Link

Orange

10 Mbps Ethernet connection.

Green

100 Mbps Ethernet connection.

Off

Ethernet cable is disconnected, or has a short.

Tx/Rx

Orange

Serial port is receiving data.

Green

Serial port is transmitting data.

Off

No data is being transmitted or received

through the serial port.

Adjustable pull high/low resistor for RS-422/485 (150

KΩ or 1 KΩ)

Jumpers are used to set the pull

high/low resistor values. The default is

150 KΩ. Short the jumpers to set this

value to 1 KΩ. Do not use the KΩ setting

with RS

-232 mode, since doing so will

degrade the RS

-232 signals and shorten

the communicati

on distance.

Hardware Installation Information

STEP 1: After removing the NPort 5100 device server from the box,

connect the NPort 5100 device server to a network. Use a standard

straight-through Ethernet cable to connect to a hub or switch. When

setting up or testing the NPort 5100 device server, you might find it

convenient to connect directly to your computer’s Ethernet port. In this

case, use a cross-over Ethernet cable.

STEP 2: Connect the NPort 5100 device server’s serial port to a serial

device.

STEP 3: Connect the power adaptor.

STEP 4: Placement options

- 5 -

In addition to placing the

NPort 5100

on a desktop or

other horizonta

l surface,

you may also make use of

the DIN

-Rail or Wall Mount

options, as illustrated here.

Wall Mount

DIN-Rail

NOTE

The operating temperature of the power adapter in the box is

from 0 to 40°C. If your application is out of this range, please

use

a power adapter supplied by UL Listed External Power

Supply (The power output meets SELV and LPS and rated 12

48 VDC, minimum current 0.73 A). Moxa has power adapters

with wide temperature range (

-40 to 75°C, -40 to 167°F), the

PWR-12150-(plug type)-SA-T series, for your reference.

For the NPort’s configuration, the default IP address of the NPort is:

LAN: Static IP = 192.168.127.254; netmask = 255.255.255.0

You may log in with the password moxa to change any setting to meet

your network topology (e.g., IP address) or serial device (e.g., serial

parameters). If you would like to apply the Real COM mode to your

application, you will need to install the NPort’s driver on your desktop.

You may also refer to Moxa’s support website

https://www.moxa.com/support/ for the user’s manual, driver, NPort

Search Utility, and more.

NOTE

For the NPort with DB Male serial ports, you may refer to the

DB9 Male Ports

Pin Assignment section to loop back pin 2 and

pin 3 for the RS

-232 interface to carry out a self test on the

device.

Pin Assignments

Ethernet Port Pinouts

Pin No.

Ethernet

Tx+

Tx-

Rx+

Rx-

- 6 -

NPort 5110—DB9 male (RS-232) port pinouts

Pin No.

RS-232

DCD

RxD

TxD

DTR

GND

DSR

RTS

CTS

–

NPort 5130—DB9 male (RS-422/485) port pinouts

Pin No.

RS-422/485-4W

RS-485-2W

TXD-(A)

–

TXD+(B)

–

RXD+(B)

Data+(B)

RXD-(A)

Data-(A)

GND

–

NPort 5150—DB9 male (RS-232/422/485) port pinouts

Pin No.

RS-232

RS-422/485-4W

RS-485-2W

DCD

TXD-(A)

–

RxD

TXD+(B)

–

TxD

RXD+(B)

Data+(B)

DTR

RXD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

Specifications

Power Requirements

Power Input

12 to 48 VDC

Power Consumption

NPort 5110: 128.7 mA @ 12V, 72 mA @ 24V

NPort 5130: 200 mA @ 12V, 106 mA @ 24V

NPort 5150: 200 mA @ 12V, 106 mA @ 24V

Operating Temperature

0 to 55°C (32 to 131°F), for standard models

-40 to 75°C (-40 to 167°F), for -T models

Operating Humidity

5 to 95% RH

Dimensions

75.2 x 80 x 22 mm

(2.96 x 3.15 x 0.87 in)



including ears

52 x 80 x 22 mm

(2.05 x 3.15 x 0.89 in)

without ears

Serial Line Protection

15 KV ESD for serial port

Magnetic Isolation

1.5 KV for Ethernet

Power Line Protection

Level 2 Burst (EFT), EN61000-4-4

Level 2 Surge, EN61000-4-5

Regulatory Approvals

FCC Class A, CE Class A, UL, LVD

- 7 -

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Serveur

Moxa Technologies

Moxa Technologies NPort 5210A Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2600 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA5150A Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IAW5000A- I/O Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5200 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort W2250 Plus Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort Server Lite DE-302 Manuel

Moxa Technologies

Moxa Technologies NPort 5000AI-M12 Manuel utilisateur

Moxa Technologies

Moxa Technologies VPort 2110 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort W2150A-T Manuel utilisateur

Moxa Technologies

Moxa Technologies 5600 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5200 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5600-8-DTL Series Manuel utilisateur

Moxa Technologies

Moxa Technologies VPort 2110 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort DE-311 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5210-T Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5200 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5600 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5100A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies MiiNePort E1-SDK Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur