Moxa Technologies NPort 5200 Series Manuel utilisateur

Released on Jun 2, 2023

About Moxa

Moxa is a leading provider of edge connectivity, industrial computing, and network infrastructure

solutions for

enabling connectivity for the Industrial Internet of Things. With 35 years of industry

experience, Moxa has connected more than 82 million devices worldwide and has a distribution and

service network that reaches customers in more than 80 countries. Moxa d

elivers lasting business

value by empowering industry with reliable networks and sincere service for industrial

communications infrastructures. Information about Moxa’s solutions is available at

www.moxa.com

How to Contact Moxa

Tel: 1-714-528-6777

Fax:

1-714-528-6778

NPort's Pair Connection Mode

Moxa Technical Support Team

support@moxa.com

Contents

1What is Pair Connection Mode? ................................................................................. 2

2How to Configure Pair Connection Mode.................................................................... 3

2.1 DE-211/DE-311/DE-311M .............................................................................. 3

2.2 NPort 5000 Series........................................................................................... 3

2.3 NPort Wireless Series and NPort 6000 Series ................................................. 4

3How to Test Pair Connection Mode ............................................................................ 5

4Cable Wiring.............................................................................................................. 5

Moxa Tech Note

NPort's Pair Connection Mode

Page 2 of 5

This Tech Note applies to the following NPort device server models:

•NPort DE-211

•NPort DE-311

•NPort DE-311M

•NPort 5100 Series

•NPort 5200 Series

•NPort 5400 Series

•NPort 5600 Series

•NPort IA5150

•NPort IA5250

•NPort W2150 Plus (wireless)

•NPort W2250 Plus (wireless)

•NPort W2150A and NPort W2250A Series (wireless)

•NPort W2150A-W4/W2250A-W4 Series (wireless)

•NPort 6000 Series

1What is Pair Connection Mode?

The Pair Connection Master and Slave modes connect two NPort device servers over an

Ethernet network for serial-to-serial communication. The two NPort device servers can

connect to each other with an Ethernet cable, connect to the same LAN, or in a more

advanced setup, communicate with each other over a WAN (i.e., through one or more

routers). A device attached to one NPort can then communicate transparently with a

device attached to the other NPort, as if a serial cable connected the two devices. Both

data and modem control signals are transmitted, although DCD signals are not. NPort’s

Pair Connection modes can overcome the distance limitations inherent in serial

communication and introduce many new possibilities for serial-based device control.

Moxa Tech Note

NPort's Pair Connection Mode

Page 3 of 5

2How to Configure Pair Connection Mode

Before continuing, push the “RESET” button for 10 seconds to reset your NPort to its

default settings.

2.1 DE-211/DE-311/DE-311M

1. Power ON the NPort; the Ready LED indicator will light up in green.

2. For RS-232 transmission, set the DE-311’s DIP switches to OFF-OFF-OFF, set the

DE-211’s DIP switches to OFF-OFF-OFF-OFF, or set the DE-301/331’s serial setting

to RS-232.

3. Connect the host PC and NPort to the network.

4. If necessary, reconfigure the IP address and netmask of your PC and the NPort so that

they are on the same subnet. The NPort’s default IP/netmask is

192.168.127.254/255.255.255.0. Test the connection by pinging from the PC to the

NPort.

5. Log in to the NPort’s Telnet console. E.g. # telnet <NPort’s IP>

6. Open [OP_mode] and select application [Pair Connection (Master)]. Under “more

setting” set [Remote IP Address] to the IP address of the other NPort (which will be

configured for [Pair Connection (Slave)])

7. Open [Serial port] to configure the serial parameters and terminal software to match

your serial device (e.g., 115200, N, 8, 1).

8. Remember to select [Restart] to activate all settings.

2.2 NPort 5000 Series

1. Power ON the NPort; the Ready LED indicator will light up in green.

2. Connect the host PC and NPort to the network.

3. If necessary, reconfigure the IP address and netmask of your PC and the NPort so that

they are on the same subnet. The NPort’s default IP/netmask is

192.168.127.254/255.255.255.0. Test the connection by pinging from the PC to the

NPort.

4. Log in to the NPort’s Telnet console. E.g. # telnet <NPort’s IP>

5. Open Main menu > Operating settings > Port > Operating mode [Pair Connection

Master mode], and configure the [IP address] and [port] to match up with the

other NPort’s settings.

6. Open Main menu > Serial settings > Port to configure the serial parameters for the

terminal software to match the serial device (e.g., 115200, N, 8, 1).

7. Remember to select [Save/Restart] to activate all settings.

Moxa Tech Note

NPort's Pair Connection Mode

Page 4 of 5

2.3 NPort Wireless Series and NPort 6000 Series

1. Power ON the NPort; the Ready LED will light up in green.

2. Connect the host PC and NPort to the network.

3. If necessary, reconfigure the IP address and netmask of your PC and the NPort so that

they are on the same subnet. The NPort’s default IP/netmask is

192.168.127.254/255.255.255.0. Test the connection by pinging from the PC to the

NPort.

4. Log in to the NPort’s Telnet console. E.g. # telnet <NPort’s IP>

5. Open [Port] > [Modes] and set Application to [Pair Connection]. Under

Description/more settings, set [Pair_Master], [IP address], and [port] to match

up with the other NPort.

6. Open [Port] > [Line] to configure the serial parameters for your terminal software

to match the serial device (e.g., 115200, N, 8, 1).

7. Remember to select [Restart] to activate all settings.

Note For wireless NPort products (both non-Plus and Plus models), you can activate either the

Ethernet port or WLAN, but not both at the same time. If you use the Ethernet port, the

WLAN will be disabled. If you want to the use WLAN, you must first unplug the Ethernet

cable and restart the NPort to activate the WLAN connection.

Note 1. The default value of [TCP port] is 4001.

2. For the NPort DE-211/311/311M device servers, only the NPort with the IP address

configured in [Destination IP addr] will be able to connect to this NPort. Leave this

column empty to allow all other NPorts to connect to this NPort.

3. The default WLAN IP address is 192.168.126.254.

Moxa Tech Note

NPort's Pair Connection Mode

Page 5 of 5

3How to Test Pair Connection Mode

1. Configure NPort#1 for Pair Connection Master and NPort#2 for Pair Connection Slave,

and then assign proper IP addresses to both NPorts.

2. Connect a different PC to each of the two NPorts’ serial ports, and then use terminal

software (e.g., HyperTerminal or Moxa’s PComm Terminal Emulator) to test

communication.

3. Pair Connection mode has been established if you can transmit data from the COM

port of PC#1 to the COM port of PC#2, as shown on the terminal, and also see that

PC#1 can receive data from PC#2.

4Cable Wiring

Autres manuels pour NPort 5200 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Moxa Technologies Serveur

Moxa Technologies

Moxa Technologies NPort W2250A Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5610 series Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2610 series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA5150A Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5200 Serie Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort Express DE-211 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort W2250 Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2610 series Manuel utilisateur

Moxa Technologies

Moxa Technologies EtherDevice Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort IA5000A-I/O series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 6150 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort S8455I Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2510-8 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort W2150A Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2510 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies CN2510 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5150AI-M12 Manuel utilisateur

Moxa Technologies

Moxa Technologies ioLogik R2140 Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 6150 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 6450 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort 5100A Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort Server Lite DE-302 Manuel

Moxa Technologies

Moxa Technologies NPort S8000 Series Manuel utilisateur

Moxa Technologies

Moxa Technologies NPort W2150 Plus Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur