Morso SQUIRREL 551 Manuel utilisateur

Manufactured by Morsø Jernstøberi A/S . DK-7900 Nykøbing Mors

E-Mail: [email protected] · Website: www.morsoe.com

Squirrel - Gas Stoves

Model No. 551 - With Open Flue

INSTALLATION INSTRUCTIONS

Distributed by Morsø UK, Unit 5, io Center, Valley Drive, Swift Walley,

Rugby, Warks, CV21 1TW - www.morsouk.com

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20)

WHEN CONVERTED USING CONVERSION KIT NO. 555111 THIS AP-

PLIANCE IS FOR USE WITH PROPANE GAS (G31)

THIS APPLIANCE IS SUITABEL ONLY FOR USE IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE) ONLY.

INSTALLER: Please leave this guide with the owner

We trust that these instructions give sufﬁcient details to enable this ap-

pliance to be installed and maintained satisfactorily. However, if further

information is required, our Technical Helpline will be pleased to help.

Telephone 01788554410 (National call rates apply in the United Kingdom).

LIST OF CONTENTS

Section Heading Page

1. SAFETY 3

2. APPLIANCE DATA 3

3.GENERAL INSTALLATION REQUIREMENTS 4

4. STOVE LOCATION 6

5. GAS SUPPLY CONNECTION 6

6. PACK CONTENTS 7

7. IGNITION CHECK 7

8. FITTING THE CERAMIC FUEL EFFECT

AND BURNER COMPARTMENT WALLS 8

9. FINAL CHECKS 10

9.1 Checking the full operating sequence. 10

9.2 Checking the reference pressure. 11

9.3 Check for spillage 12

10. FINAL REVIEW & SERVICING 13

1. SAFETY

Installer

Before continuing any further with the installation of this appliance please

read the following guide to manual handling.

• The lifting weight of this appliance is 53.5 kg.

• This stove is heavy. We therefore recommend that two people

should be sufﬁcient to lift the stove. If ﬁtting or moving the appliance

alone we recommend the use of suitable lifting apparatus.

• When lifting always keep your back straight. Bend your legs and not

your back.

• Avoid twisting at the waist. It is better to reposition your feet.

• Avoid upper body/top heavy bending. Do not lean forward or

sideways whilst handling the stove.

• Always grip with the palm of the hand. Do not use the tips of ﬁngers

for support.

• Always keep the stove as close to the body as possible. This will

minimise the cantilever action.

• Use gloves to provide additional grip.

• Always use assistance if required.

2. APPLIANCE DATA

This product uses fuel effect pieces, burner compartment walls and gaskets

containing Refractory Ceramic Fibres (RCF), which are man-made vitreous

silicate ﬁbres. Excessive exposure to these materials may cause temporary

irritation to eyes, skin and respiratory tract. Consequently, it makes sense to

take care when handling these articles to ensure that the release of dust is

kept to a minimum. To ensure that the release of ﬁbres from these RCF articles

is kept to a minimum, during installation and servicing we recommend that

you use a HEPA ﬁltered vacuum to remove any dust and soot accumulated in

and around the stove before and after working on the stove. When replacing

these articles we recommend that the replaced items are not broken up, but

are sealed within a heavy duty polythene bag, clearly labelled as RCF waste.

This is not classiﬁed as “hazardous waste” and may be disposed of at a

tipping site licensed for the disposal of industrial waste. Protective clothing

is not required when handling these articles, but we recommend you follow

the normal hygiene rules of not smoking, eating or drinking in the work area

and always wash your hands before eating or drinking.

This appliance does not contain any component manufactured from as-

bestos or asbestos related products.

The stove dimensions are shown in ﬁgure 1

3. GENERAL INSTALLATION REQUIREMENTS

The installation must be in accordance with these instructions.

For the user’s protection, in the United Kingdom it is the law that all gas

appliances are installed by competent persons in accordance with the cur-

rent edition of the Gas Safety (Installation and Use) Regulations. Failure to

install the appliance correctly could lead to prosecution. The Council for

the Registration of Gas Installers (CORGI) requires its members to work to

recognised standards.

In the United Kingdom the installation must also be in accordance with:

a) All the relevant parts of local regulations.

b) The current edition of the Building Regulations issued by the Department

of the Environment and the Welsh Ofﬁce or the Building Standards (Scot-

land) Regulations issued by the Scottish Development Department.

c) All relevant codes of practice.

d) The relevant parts of the current editions of the following British Stand-

ards:-

BS 1251

BS 5440 Part 1

BS 5440 Part 2

BS 5871 Part 1

BS 6891

BS 8303

Gas Natural (G20) Propane (G31)*

Inlet Pressure 20mbar 37mbar

Input Max. (Gross) 5.7 kW (19,450 Btu/h) 5.1 kW (17,400 Btu/h)

Min. (Gross) 1.7 kW (5,800 Btu/h) 1.9 kW (6,485 Btu/h)

Output Max. (Gross) 3.8 kW (12,970 Btu/h) 3.6 kW (12,285 Btu/h)

Min. (Gross) 1.1 kW (3,755 Btu/h) 1.2 kW (4,095 Btu/h)

Burner Test Pressure (Cold) 19.6 +0.75mbar 35.9+0.75 mbar

(7.86 ± 0.3 in w.g.) (14.41 ± 0.3 in w.g.)

Gas Connection 8 mm pipe 8 mm pipe

Burner Injector Cat. 82 Size 360 Cat. 92 size 160

Ignition Piezo Electric. Piezo Electric.

Intergral with Gas Tap Intergral with Gas Tap

Gas rate 0.539m3/h 0.190m3/h

Efﬁciency class 2 2

* When converted using Kit no. 555211.

In the Republic of Ireland the installation must also conform to the relevant

parts of:

a) The current edition of IS 813

b) All relevant national and local rules in force.

c) The current building regulations.

Where no speciﬁc instructions are given, reference should be made to the

relevant British Standard Code of Practice.

The hearth must be made from a non-combustible material and be at least

400mm wide x 420mm deep x 12mm thick.

Clearances from combustible and non-combustible materials must be at

least those shown in ﬁgure 1.

Figure 1

The ﬂue details are shown in ﬁgure 1.

• The minimum ﬂue diameter is 120mm.

• The minimum ﬂue height is 3m.

• The maximum horizontal ﬂue length is 300mm.

• No restrictor plate or ﬂue damper is permitted. Where a variable damper

is ﬁtted it must be removed or be permanently ﬁxed in the

open position.

• The ﬂue must be swept before the appliance is installed.

Ventilation: Normal adventitious ventilation is usually sufﬁcient to satisfy the

ventilation requirements of this appliance. In GB reference should be made

to BS 5871 Part 2 and in IE reference should be made to the current edition

of IS 813 “Domestic gas Installations” which makes clear the conditions that

must be met to demonstrate that sufﬁcient ventilation is available.

Location: This appliance must not be installed in a private garage or any room,

which contains a bath, or shower or where steam is regularly present.

Propane gas appliances must not be installed in a cellar, basement or other

room which is built entirely below ground level (See Gas Safety (Installation

& Use) Regulations).

A ﬁreguard complying with BS 8423 should be ﬁtted for the protection of

young children, the elderly, or the inﬁrm. Such a guard is also recommended

for the protection of pets.

Atmosphere sensing device. The appliance is ﬁtted with an A.S.D (Atmos-

phere sensing device). If the appliance closes down after a period of operation

for no apparent reason, the consumer should be informed to stop using the

appliance until the installation and appliance have been thoroughly checked.

The A.S.D will shut the appliance down if an unacceptable amount of harm-

ful products of combustion accumulate. Under no circumstances should

the A.S.D be altered or bypassed in any way. Only a genuine manufacturers

replacement part should be ﬁtted. The individual A.S.D components are not

replaceable.

4. STOVE LOCATION

1. Decide on whether the stove is to be used in rear or top outlet set-up and

remove the appropriate outlet cover plate. The cover plate must be securely

attached to the unused ﬂue outlet.

2. Place the stove in position on the hearth ensuring that the minimum di-

mensions speciﬁed in ﬁgure 1 are adhered to. Connect the ﬂue pipe to

the outlet and seal in place.

3. Due to its weight there is normally no requirement for additional ﬁxing

with this appliance.

5. GAS SUPPLY CONNECTING

• A nut and olive are provided for an 8mm pipe inlet connection to the

elbow at the bottom front of the appliance. The elbow can be rotated to

allow a connection from any direction. The elbow includes a valve for

isolating the gas supply.

• The supply pipe must be rigid material. Flexible pipe must not be used.

• Note: Prior to connecting the gas supply it is advisable to blow out

the gas supply so that any dirt which may be present in the pipe is

cleared and cannot enter the gas valve or pilot burner and so cause a

blockage.

• With the supply connected pressure check the installation pipework for

gas soundness. In the United Kingdom check in accordance with the

current edition of BS6891. In the Republic of Ireland check in accordance

with the rules in force.

6. PACK CONTENTS

1 Cast iron stove containing gas burner unit & interior ﬂueway

1 8mm nut & olive

1 Key for door

1 Rope seal

2 Ceramic base pieces

1 Set of 7 coals

1 Pair of ceramic ﬁrebox side walls

2 Side wall retaining brackets

1 Ceramic ﬁrebox back wall

Remove all the items carefully to prevent damage. Take special care when

handling the ceramic components. Some items may be contained in the

packaging ﬁtments - Examine the packaging carefully before discarding.

Check that all the items are present and undamaged.

7. IGNITION CHECK

Before attempting to install, it is worth checking that the ignition system

performs satisfactorily.

Set the right hand control knob to the off position marked •.

Depress the right hand control knob and rotate it anticlockwise through the

ignition position marked to the pilot ignition position marked . A ‘click’

will be heard as the integral piezo operates. A spark should be seen between

the electrode and pilot tip. If there is no spark check the following: -

• Ensure that the electrode lead is connected to the terminal at the base

of the electrode.

• If the above is correct, check for damage to the electrode lead.

8. FITTING THE CERAMIC FUEL EFFECT & BURNER

COMPARTMENT WALLS

1. The door is secured with a locking screw. Remove the screw with the

allen key supplied (See ﬁgure 2). Open the door.

2. Remove the front grate. To do this, hold ﬁrmly and lift.

3. Place the rear ceramic wall against the back of the ﬁrebox.

4. The rear ceramic wall must be located onto the ledges at the back of

the rear base ceramic (See ﬁgure 3). To achieve this, hold the rear ceramic

wall against the rear of the ﬁrebox at its uppermost position. Whilst holding

the rear ceramic wall in this position locate the rear ceramic base coal into

position (See ﬁgure 3). The rear wall can now be released. Ensure that the

rear ceramic wall sits on the ledge at the back of the rear base coal.

5. Fit the left hand side wall against the left hand side of the ﬁrebox. Locate

the bottom of the side wall into the channel along the bottom of the ﬁrebox

(See ﬁgure 4). Supplied with the stove are two ceramic retaining brackets.

One for each side of the ﬁrebox. Hold the ceramic side wall against the steel

ﬁrebox plate and slide the long leg of a retaining bracket behind the steel

ﬁrebox plate. Push down to hold the ceramic side wall in place.

6. Fit the right hand side wall against the right hand side of the ﬁrebox.

Locate the bottom of the side wall into the channel along the bottom of the

ﬁrebox. Hold the ceramic side wall against the steel ﬁrebox plate and slide

the long leg of a retaining bracket behind the steel ﬁrebox plate. Push down

to hold the ceramic side wall in place.

7. On the front of the burner there is a bracket for supporting the front ce-

ramic base. At the rear of the front ceramic base is a recess. Fit the front

ceramic base piece locating the recess onto the forward projecting part of

the burner bracket (See ﬁgure 5).

There are seven overlay coals. There are three ceramic coals identiﬁed with

the number’1’. Two identiﬁed with the number ‘2’ and two identiﬁed with

the number ‘3’.

8. Locate one of the ceramic coals identiﬁed with a number ‘1’ as in ﬁgur

9. Locate the two ceramic coals identiﬁed with a number ‘2’ as in ﬁgure 7.

10. Locate the remaining two ceramic coals identiﬁed with a number ‘1’ as

in ﬁgure 8.

11. Locate the two ceramic coals identiﬁed with a number ‘3’ as in ﬁgure

12. Replace the front grate previously removed .

13. Close and secure the door by reﬁtting the locking screw.

Figure 2

Figure 3

Figure 4

Figure 5

Figure 6 Figure 7

Figure 8 Figure 9

9. FINAL CHECKS

9.1 Checking the full operating sequence.

See ﬁgure 10.

If the ﬁre is turned off or the ﬂames go out, wait at least 3 minutes before

attempting to relight. A safety device in the control stops the ﬁre being turned

back on until it is safe.

Figure 10

Autres manuels pour SQUIRREL 551

Table des matières

Autres manuels Morso Poêle

Morso

Morso 2B Classic Manuel utilisateur

Morso

Morso S11-40 Manuel utilisateur

Morso

Morso S81-90 Manuel utilisateur

Morso

Morso 6100 series Manuel utilisateur

Morso

Morso 6140 Manuel utilisateur

Morso

Morso S50-40 Manuel utilisateur

Morso

Morso 2B Classic Manuel utilisateur

Morso

Morso 1710 Insert Manuel utilisateur

Morso

Morso 8140 Manuel utilisateur

Morso

Morso 7840 Manuel utilisateur

Morso

Morso 3400 Series Manuel utilisateur

Morso

Morso S10 Manuel utilisateur

Morso

Morso 3112 Manuel utilisateur

Morso

Morso 7600 series Manuel utilisateur

Morso

Morso 1412 Manuel utilisateur

Morso

Morso 4000 Manuel utilisateur

Morso

Morso 1410 Manuel utilisateur

Morso

Morso 3440 Manuel utilisateur

Morso

Morso DB15 Manuel utilisateur

Morso

Morso Panther Manuel utilisateur

Morso

Morso 7400 SERIES Manuel utilisateur

Morso

Morso DB15 Manuel utilisateur

Morso

Morso 1440B Manuel utilisateur

Morso

Morso 3100 Series Manuel utilisateur

Manuels Poêle populaires d'autres marques

Arada

Arada Cassette Stove Manuel utilisateur

Parmco

Parmco FS 600 Manuel utilisateur

MCZ

MCZ SUITE AIR 10 M2 Manuel utilisateur

HearthStone

HearthStone Stowe DV 8321 Guide de dépannage

Cattara

Cattara FAMILY Manuel utilisateur

Stanley

Stanley Argon F500 OVAL Manuel utilisateur

Avalon

Avalon B-VENT Manuel utilisateur

Nordpeis

Nordpeis Vega Manuel utilisateur

Exquisit

Exquisit EKC601-5 Manuel d'utilisation

Stanley

Stanley Oisin Oil MK II Manuel du propriétaire

Thermocet

Thermocet Brookfield S/CC Manuel utilisateur

HASE

HASE delhi Manuel utilisateur

Vermont Castings

Vermont Castings Intrepid 2 Manuel utilisateur

Italiana Camini

Italiana Camini CLASSICA Guide de démarrage rapide

Avalon

Avalon Vashon Avanti DVS FS Manuel utilisateur

Spartherm

Spartherm ambiente a1 Manuel utilisateur

Dimplex

Dimplex MCFSTV12AU Manuel utilisateur

Warmlite

Warmlite WL46040 Manuel utilisateur