Monitor Audio CLG140 Manuel utilisateur

Installation Guide

Guide d'installation

Manuale di installazione

Installationsanleitung

Guía de instalación

Guia de instalação

Installatiehandleiding

安装指南

Руководство по установке

インストールガイド

 

 

Contents

Languages

Wiring the Speakers and Subwoofer 1

Speaker Positioning 1

Installation 2

CLG-W12 2

CLG140/ CLG160 - With Spike 3

CLG140/ CLG160 - Wall Mount 4

CLG140/ CLG160 - Tree Mount 4

System Setup 5

Mono System 5

Stereo System 6

Monitor Audio Preset DSP List 6

CLG DUAL 6

CLG SATS 6

CLG SUBS 6

Installing MA Presets on your Crown CDi 2000

Amplier 7

Specications 8

Guarantee 9

English 1

Français 10

Italiano 20

Deutsch 30

Español 40

Português 50

Nederlands 60

中文 70

РУССКИЙ 80

日本語 90

ﺔﻴﺑﺮﻌﻟا 100

Introduction

Bring high delity sound to the great outdoors with Monitor Audio’s latest custom installation solution, the Climate Garden

Series. Designed from the ground up with high quality components and construction to take whatever the weather can throw at

them. Aesthetically they will blend seamlessly into the garden environment. To get the most out of your new speakers, please

read this manual thoroughly before you begin installation.

Wiring the Speakers and Subwoofer

The CLG140/ CLG160 speakers work o a 100v/ 70v system and CLG-W12 can work o a 100v/ 70v system or can be hooked

up to a conventional amplier (8 Ohm tap). NOTE: This will not work if connected to the subwoofer output at phono level. A

70v Line system is mainly used in the U.S whereas the U.K and Europe use 100v line systems. The two dierent voltages will

work just the same, although the amplier may not deliver its full power into 100v as this will be limited by the voltage rails

-unless it is switchable. The 8 Ohm tap is conventional speaker impedance and it means only one sub per channel can be used,

in contrast to using 100/ 70v line, where you can use multiple subs in a system. It is transformer isolated, and it will protect

the speaker from D.C. oset or D.C. amp faults.

The speakers should be connected in parallel from a single cable run per channel. We also recommend using the Crown CDi

2000 amplier and our bespoke DSP settings.

Speaker Positioning

The Climate Garden Series is designed to deliver a seamless, evenly dispersed audio experience in an ‘open air’ environment.

To minimize the occurrence of ‘hot spots’ and ‘nulls’ as you move around the outdoor entertainment area, an array of multiple

satellite speakers can be strategically placed for even coverage. The CLG140/ CLG160 can cover an area up to 250 square feet

and should be positioned an equal distance from each other and the listening area, or as close as possible. A single CLG-W12

can cover an area between 1000 - 2000 square feet. We would recommend placing the subwoofer in a centralised location in

accordance with the other speakers.

To centralise the sound stage high and low speakers can be used.

monitoraudio.com 1

ENGLISH

Dig a hole in the intended location for the

subwoofer and ll the base of the hole with

sharp sand. This is to improve stability, assist in

levelling and prevent the sub from rocking in place.

Approximate hole dimensions (H x W x D):

600 x 600 x 400mm

Sand depth: 150mm (6”)

1 2

Sharp sand

Dig a shallow trench along the path of where

you wish to run the subwoofer’s speaker

cables. If using the CLG140/ CLG160 speakers there

is no reason the cables for these cannot be doubled

up in the same trench as the subwoofer’s speaker

cables.

Place the subwoofer in the hole and push it

into the sand so that it stays still and can be

levelled/ made square.

NOTE: Ensure the system is tested and working correctly before lling in around the subwoofer and cable tenches.

NOTE: The bass from the CLG-W12 will not be as full or prominent until the hole is lled in.

Installation

CLG-W12

Climate Garden Series2

4Connect cables to subwoofer. For 100/70v

lines (such as the Crown CDi 2000) connect

to the black and red cables, for conventional 8 ohm

lines connect to the yellow and black. Where black

is the negative.

To Next CLG-W12

(optional)

To CLG-W12

From previous

speaker/ amp

Connections

should be made

with either

silicone lled

wire connectors

(example

opposite) or appropriate weather proof junction box

(not included).

Note: Ensure that no ‘-’ and ‘+’ strands are

touching each other as this will cause a short

circuit that could damage your amplifer.

First screw the threaded section supplied

(i) onto the CLG140/ CLG160 speaker, once

secure thread the cables attached to the speaker

through the hole in the spike before attaching the

spike to the threaded section (ii).

Dig a shallow trench along the path of

where you wish to run the speaker cables.

1Once assembled, the speaker

can now be installed in the

desired location.

The pivot angle of the CLG140/

CLG160 can be adjusted using

an allen key.

Note: It is advised to hold the

speaker from the spike whilst doing

this so that no pressure is placed on

the pivoting section.

ENGLISH

CLG140/ CLG160 - With Spike

NOTE: Ensure the system is tested and working correctly before lling in around the subwoofer and cable tenches.

monitoraudio.com 3

4Connect speaker’s cables in parallel with

the main run of cable from the amplier

combining all positive cable together and all

negative cables together.

To Next speaker

To CLG140/

CLG160

From previous

speaker/ amp

Connections

should be made

with either

silicone lled

wire connectors

(example

opposite) or appropriate weather proof junction box

(not included).

Note: Ensure that no ‘-’ and ‘+’ strands are

touching each other as this will cause a short

circuit that could damage your amplifer.

Feed the speaker cable into the bracket

and out through the cable exit hole. Place

the CLG140/ CLG160 (i) onto the bracket and t the

grub screws (ii) but do not fully tighten. Adjust the

CLG140/ CLG160 to the desired direction/ angle

and tighten the four mount screws (refer to step 1)

followed by the grub screws (ii) to secure in place.

Fix the base of the mount to the intended

location with a single screw (i), then

insert the ball xing arm and top half of the mount

assembly, attach loosely with four screws (ii).

CLG140/ CLG160 - Wall Mount

CLG140/ CLG160 - Tree Mount

HINT: To assist in threading the speaker cable

through the mount we would advise having the

ball xing arm angled upwards.

iii

A tree belt (not included) can now be

threaded through the opening in the sides

of the mount. Wrap this around the intended tree and

fasten the belt tightly to prevent movement.

Assemble the two halves of the mount

with the ball xing arm in the middle and

secure it together using the supplied nuts and bolts

supplied with the mount.

Climate Garden Series4

Once the mount is xed to the intended

location, thread through the speaker cable

and attach the CLG140/ CLG160 (i). Secure in place

with the two grub screws (ii).

HINT: To assist in

threading the speaker

cable through the

mount we would advise

having the ball xing

arm angled upwards.

Amp

Channel 1Channel 2

CLG DUAL

3Connect speaker’s cables in parallel with

the main run of cable from the amplier

combining all positive cable together and all

negative cables together.

To Next speaker

To CLG140/

CLG160

From previous

speaker/ amp

Connections

should be made

with either

silicone lled

wire connectors

(example

opposite) or appropriate weather proof junction box

(not included).

Note: Ensure that no ‘-’ and ‘+’ strands are

touching each other as this will cause a short

circuit that could damage your amplifer.

System Setup

To power the system we would recommend using the Crown CDi 2000 amplier. For optimum performance from the system

download the Monitor Audio Crown CDi 2000 preset DSP settings from our website: www.monitoraudio.com

These preset DSP settings have been designed by Monitor Audio to bring the best performance from your satellite speakers

and sub, with a crossover in place to direct only the low frequencies to the subwoofer and mid-highs to the satellites. This will

allow each component to focus on what is does best, adding clarity to the system and also protecting the satellite speakers

from potentially harmful/ overbearing sub frequencies.

Mono System

With Monitor Audio’s preset DSP settings installed (refer to page 6 and 7) and the ‘CLG DUAL’ preset selected on the amplier

the Crown CDi 2000 will send mid-high frequencies to channel 2 and bass frequencies to channel 1. Connect the sub to channel

1 and the satellites in parallel to channel 2 (expandable to a maximum of 30 speakers).

Note: Due to the nature of garden listening Monitor Audio would recommend a Mono system for the majority of

installations.

ENGLISH

monitoraudio.com 5

Stereo System

With Monitor Audio’s preset DSP settings installed (refer to page 6 and 7) and the ‘CLG SATS’ preset selected on the amplier

the Crown CDi 2000 will play the left audio through Channel 1 and right through Channel 2 (both expandable to a maximum of

30 speakers). A separate amplier can be connected with Monitor Audio’s ‘CLG SUBS’ preset (refer to the next section below)

for the addition of any subwoofers.

Monitor Audio Preset DSP List

CLG DUAL

Channel 1 has a low pass lter for the subwoofer and Channel 2 has a high pass lter for the satellite speakers.

CLG SATS

Channel 1 and 2 have high pass lters for the satellite speakers (intended for stereo systems).

CLG SUBS

Channel 1 and 2 have low pass lters for additional subwoofers (for use with either multiple sub’s or a single sub in addition

to a stereo satellite system running ‘CLG SATS’ DSP on another amp).

Amp

Channel 2 Channel 1

Channel 1

CLG SATS

CLG SUBS

Climate Garden Series6

Installing MA Presets on your Crown CDi

2000Amplier

1. Download Monitor Audio’s preset DSP settings for your

Crown CDi 2000 amplier, available from our website:

www.monitoraudio.com

2. Download the software HiQnet Audio Architect from the

website: http://audioarchitect.harmanpro.com/en-

US/software

3. Open the downloaded zip folder, extract the executable

le to your desktop and run it, proceeding through the

steps of the Installation Wizard.

4. Once installation is complete launch Audio Architect.

5. Close the ‘Crash Reporting Disclaimer’ and ‘Application

Options’ window. You can now select your network

connection, or to skip this step, simply close the window.

6. Connect the Crown CDi 2000 via USB cable to your

computer and switch on the power button, the ready

LED and power button will become illuminated.

7. Once discovered a pop up will appear in Audio

Architect, check ‘Add discovered devices to the Venue

automatically’ is ticked and then press close.

8. Your Crown CDi 2000 will now appear in the application

window and the ‘Go Online’ button will become

illuminated. Press ‘Go Online’.

HINT: Maximise the Audio Architect application

window to see the buttons as they are shown in

these steps.

9. Press the ‘R’ (Recall) button, circled below.

10. Select the amp with a left click, then right click to show

the drop down options, press ‘Open Device File...’.

11. Open the Monitor Audio preset le.

12. You have now successfully installed our Monitor Audio

presets on your Crown CDi 2000.

NOTE: There is no notication of this being

successful.

ENGLISH

monitoraudio.com 7

CLG140 CLG160

Frequency Response (-6dB) 100Hz – 30KHz 80Hz – 30KHz

Sensitivity (1W@1m) 88dB 89dB

Line Level Voltage 70/100 70/100

Maximum S.P.L 104 dBA 107 dBA

Power Handling 40 watts (crossover set to minimum

100Hz@12dB/Octave)

60 watts (crossover set to minimum

80Hz@12dB/Octave)

Amplifier Requirements

(RMS) 10-40 watts per speaker 10-60 watts per speaker

Driver Complement

1 x 4” MMPII cone bass-mid driver

1 x 25mm C-CAM Gold Dome tweeter –

Coaxially oriented

1 x 6” MMPII cone bass-mid driver

1 x 25mm C-CAM Gold Dome tweeter –

Coaxially oriented

Crossover Recommendation

(high pass)

100Hz at a minimum of 12dB/Octave

(24dB/Octave optimum)

80Hz at a minimum of 12dB/Octave (24dB/

Octave optimum)

External Dimensions,

excluding spike/ mount

(Diameter x D)

130 x 175mm (51/8 x 67/8 inches) 190 x 220mm (71/2 x 811/16 inches)

Bracket Pivot Angle 32° in all directions 32° in all directions

Connection Encapsulated cable connection Encapsulated cable connection

Environmental Protection

Rating IP55 IP55

Finishes Available Brown Brown

Weight 2.08kgs (4lb 10oz) 2.76 kg (6lb 2oz)

Dispersion 60° 60°

Specications

Climate Garden Series8

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Monitor Audio Intervenants

Monitor Audio

Monitor Audio Radius HD Manuel utilisateur

Monitor Audio

Monitor Audio CP Series Manuel utilisateur

Monitor Audio

Monitor Audio GSW12 Manuel utilisateur

Monitor Audio

Monitor Audio CP-CT260 Manuel utilisateur

Monitor Audio

Monitor Audio Gold Reference GR20 Manuel utilisateur

Monitor Audio

Monitor Audio RADIUS 45HD Manuel utilisateur

Monitor Audio

Monitor Audio GOLD GX series Manuel utilisateur

Monitor Audio

Monitor Audio Platinum 3G Series Manuel utilisateur

Monitor Audio

Monitor Audio 300 series Manuel utilisateur

Monitor Audio

Monitor Audio Vector V10 Manuel utilisateur

Monitor Audio

Monitor Audio airstream WS100 Manuel utilisateur

Monitor Audio

Monitor Audio Silver 7G Series Manuel utilisateur

Monitor Audio

Monitor Audio WT280 Manuel utilisateur

Monitor Audio

Monitor Audio AWC265-T2 Manuel utilisateur

Monitor Audio

Monitor Audio Controlled Performance series Manuel utilisateur

Monitor Audio

Monitor Audio Monitor Reference Series Manuel utilisateur

Monitor Audio

Monitor Audio Controlled Performance series Manuel utilisateur

Monitor Audio

Monitor Audio EN 50020 Manuel utilisateur

Monitor Audio

Monitor Audio PL IN-WALL II Manuel utilisateur

Monitor Audio

Monitor Audio Vector Manuel utilisateur

Monitor Audio

Monitor Audio GS10 Manuel utilisateur

Monitor Audio

Monitor Audio CT265 Manuel utilisateur

Monitor Audio

Monitor Audio PLW-15 Manuel utilisateur

Monitor Audio

Monitor Audio Bronze Series Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur