Monitech ML121QT1400 Manuel utilisateur
M20A10-ML121QT1400
1
ML1 2 1 QT1 4 0 0 INSTALL GUIDE
LCD upgrade kit
FOR YOUR 14" Allen-Bradley Panelview 1400
controller (2711-T14, 2711-K14) & 14" Allen
Bradley T60 controller 6160PCD2
M20A10-ML121QT1400
2
IMPORTANT:
WARRANTY
Before using any MONITECH product please carefully
review this Manual as well as any additional
documentation provided with your shipment.
Attempting any of the following will void product warranty:
•unauthorized repairs or parts replacement
•inappropriate use or placement: exposing product to
liquids, harmful gases, electrical shock, physical
shock, temperatures beyond the range of -4°F to
140°F
(-20°C to 60°C)
•use of electrical voltage other than 12V 4.16A
(power supply and AC cable provided)
•Removal or modification of serial, product, or
warranty labels.
WARNING
ELECTRICAL HAZARD
DO NOT OPEN
TO AVOID ELECTRICAL SHOCK DO NOT
OPEN PRODUCT CASING. UNAUTHORIZED
REPAIRS OR PARTS REPLACEMENT ARE
PROHIBITED AND WILL VOID PRODUCT
WARRANTY. PLEASE RETURN TO
MONITECH FOR REPAIRS.
M20A10-ML121QT1400
3
REMOVALE:
Step #1) Turn off turn off main power, turn off machine.
Step #2) Take the Panelview terminal out of the machine by unscrewing the
clamps holding it in the machine. Unplug the communication cable, the
power cable and the ethernet cable.
Unscrew the
clamps holding
the terminal in
your machine.
Unplug the
communication
cable, the
power cable
and the
ethernet cable.
M20A10-ML121QT1400
4
Step #5) Unscrew the screws holding the Back Cover on the terminal.
Remove the back cover off. Keep the screw removed for re-installation.
Step #6) Remove high voltage from the CRT by placing a screwdriver
underneath the rubber of the anode lead and the other end touch metal, with
another screwdriver put the tip onto metal and cross it with the first
screwdriver. Then remove the anode lead by pushing one contact in so that
it
Unscrew the
screws holding
the Back Cover
on the terminal
M20A10-ML121QT1400
5
Step #7) Unplug the video cable, the touchscreen ribbon cables, unplug the
2 pin AC power connector, and the other connectors. Unscrew the screws
that hold the CRT Chassis in place, (keep screws for re-installation). Then
take unscrew the nuts holding the CRT Chassis to the gold front frame.
Step #8) Remove the neck board, disconnect the yolk & remove all other
boards from housing they are not needed. Keep the 2-pin power cable &
keep the side computer board.
Unplug the video cable, the
touchscreen ribbon cables, unplug
the 2 pin AC power connector,
and the other connectors
M20A10-ML121QT1400
6
INSTALLATION:
Step #9) Now you are left with the old CRT housing in which you are going
to place your Monitech Monitor in. Install the four aluminum 'C' brackets
(MH2003) onto the A-B 1400 Frame using the supplied M5 nuts to secure.
Mount the LCD to the brackets using the supplied 8-32 screw and washer.
You may have to break off plastic piece to allow LCD to sit as close to the
front as possible. Mount the LCD in to the frame. If you have an
ML121LL1400 you do not need to use the MH2003.
M20A10-ML121QT1400
7
Step #10)Connect the MAV536 in to the Computer board, connect the VGA
side into the monitor. Connect the MAP302 into where the 2 pin power
connector is with butt connectors. Connect the MAP302 into MAP307, plug
in the jack into the monitor.
Step #11) Re-install the gold frame to the front bezel (Refer to Step 7). Then
test the monitor on the bench by using the AC power to the terminal. Adjust
the image using the user controls, use the user guide to guide you.
M20A10-ML121QT1400
8
Step #12) Re-install the back cover (Refer to Step 5 but
follow instructions in reverse). Mount the terminal back into
the machine, with the clamps. (Refer to Step 2 in reverse).
Plug in the power, ethernet cable and the commination cable.
Turn ON Main Power and Machine Power.
For Technical Support, Call
1-877-493-6105
Support@Monitech.com
20 Howard Place
Kitchener, Ontario N2K 4Z4
CANADA 519.725.2222
Table des matières
Autres manuels Monitech Système de contrôle
