MONARCH INSTRUMENT Phaser Strobe PBX Manuel utilisateur

Phaser-Strobe pbx

Portable Phase-Shifting Stroboscope

MONARCH INSTRUMENT

Instruction Manual

Printed in the U.S.A.

1071-4210-112R 1009

www.64817.com

Safeguards and Precautions

1. Read and follow all instructions in this manual carefully, and

retain this manual for future reference.

2. Do not use this instrument in any manner inconsistent with

these operating instructions or under any conditions that

exceed the environmental specifications stated.

3. Use of this product may induce an epileptic seizure in persons

prone to this type of attack.

4. Objects viewed with this product may appear to be stationary

when in fact they are moving at high speeds. Always keep a

safe distance from moving machinery and do no touch the target.

5. There are lethal voltages present inside this product. Refer to

the section on Lamp Replacement before attempting to open

this product.

AC Stroboscopes that have three wire mains cable must

have the earth wire connected to a suitable Earth point.

6. Do not allow liquids or metallic objects to enter the ventilation

holes on the stroboscope as this may cause permanent

damage and void the warranty.

7. Do not allow cables extending from unit to come into contact

with rotating machinery, as serious damage to the equipment,

or severe personal injury or death may occur as a result.

8. This instrument may not be safe for use in certain hazardous

environments, and serious personal injury or death could occur

as a result of improper use. Please refer to your facility’s

safety program for proper precautions.

CE DECLARATION OF CONFORMITY

As Manufacturer:

Monarch Instrument

Division of Monarch International Inc.

15 Columbia Drive, Amherst NH 03031 USA

declares under Monarch’s sole responsibility that the product:

to which this declaration relates is in conformity with the following standards:

and therefore conforms with the requirements of Council Directive 89/336/EEC

relating to electromagnetic compatibility and 73/23/EEC relating to the low voltage

directive with amendments, when operated in accordance with the user guide.

EMC testing of this product was performed by Retlif Testing Laboratories, NH, in

February of 2007 (File R-4702N-5).

Name: Nova-Strobe X Series

Models: pbx, dbx, bbx

14th February, 2007

Manufacturer (Amherst,NH) Alan Woolfson, VP Engineering (Authorized Signature)

EN61326:1997 EMC /A1:1998/A2:2001/A3:2003 Class A

Specifically CISPR 16-1:2003/CISPR 16-2:2003

EN55011:1998/A1:1999/A2:2002 EN61000-4-2 EN61000-4-3

EN61010-1:2001-2 Safety Regulation

9. This product contains Nickel Metal Hydride batteries which

must be disposed of in accordance with Federal, State, & Local

Regulations. Do not incinerate. Batteries should be shipped to

a reclamation facility for recovery of the metal and plastic

components as the proper method of waste management.

Contact distributor for appropriate product return procedures.

10. This instrument is not user serviceable. For technical

assistance, contact the sales organization from which you

purchased the product or Monarch Instrument directly.

In order to comply with EU Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE): This product

may contain material which could be hazardous to human health

and the environment. DO NOT DISPOSE of this product as un-

sorted municipal waste. This product needs to be RECYCLED in

accordance with local regulations, contact your local authorities

for more information. This product may be returnable to your distributor for

recycling - contact the distributor for details.

Monarch Instrument’s Limited Warranty applies. See

www.monarchinstrument.com for details.

Warranty Registration and Extended Warranty coverage available

online at www.monarchinstrument.com.

10.0 OPTIONS AND ACCESSORIES

PSC-pbxU Universal Power Supply/Charger, 115/230 Vac with

USA, U.K., AUS and Euro Adapter Plugs (one supplied

with unit)

C-4027 Set of mating 1/8 inch (3.5mm) stereo phone plugs (to

provide TTL signal and sensor power)

CA-4044-6 6 foot (1.8M) input / output cable, 1/8 inch (3.5mm)

male phone plug to male BNC connector

CA-4045-6 6 foot (1.8M) input / output cable, 1/8 inch (3.5mm)

male phone plug to 1/8 inch (3.5mm) male phone plug

for daisy chaining strobes together

CC-7 Latching carrying case for Strobe with provision for

accessories

L-1903 Digital Stroboscope replacement lamp

SPC-1 Splash proof Protective Cover for battery model

Stroboscopes ONLY

ROS-P Remote Optical Sensor with 8 foot (2.5 m) cable for

triggering strobe

T-5 Reflective tape. 5 foot (1.5 m) roll, 0.5 inch wide

MT-190P Magnetic Sensor/Amplifier with 8 foot (2.5 m) cable

for triggering strobe

IRS-P Infrared Sensor for use without reflective target at 0.5

inch (12 mm) gap with 8 foot (2.5 m) cable for triggering

strobe

TABLE OF CONTENTS

1.0 OVERVIEW ............................................................................. 1

1.1 Display Panel / Definition of Buttons ........................... 1

2.0 PREPARATION FOR USE ........................................................ 3

2.1 Power ............................................................................ 3

2.2 Input / Output Connections .......................................... 3

3.0 MENU ...................................................................................... 5

4.0 OPERATION ............................................................................ 6

4.1 Internal Mode - Standard Strobe Operation ............... 6

4.2 Internal Mode - TACH Frequency Generator ............... 9

4.3 External Input Mode ................................................... 10

4.4 Tachometer Mode - External Input Required ............ 10

4.5 External Delay Modes (Phase Shifting) .................... 11

4.6 Power Up Features .................................................... 11

5.0 USING THE STROBOSCOPE TO MEASURE RPM ................ 12

6.0 LIMITATIONS OF REMOTE OPTICAL SENSORS .................. 14

7.0 LAMP REPLACEMENT AND FUSE ....................................... 14

7.1 Lamp Replacement .................................................... 14

7.2 Fuse ............................................................................. 16

8.0 BATTERYAND POWER SUPPLY SPECIFICS ....................... 17

8.1 Low Battery Indication ............................................... 17

8.2 Charging the Batteries ............................................... 18

8.3 External Power Supply/Charger ................................ 19

8.4 Battery Disposal ......................................................... 19

9.0 SPECIFICATIONS .................................................................. 20

10.0 OPTIONS AND ACCESSORIES ............................................ 22

Memory Last setting before power down is remembered

and restored on next power up. 9 user settable

flash rates.

Output Pulse 40 µsec positive/negative pulse (menu

selectable), 3.3 Vdc typical

Input Power Internal Rechargeable Batteries 6 Vdc, External

AC recharger (115 Vac to 230 Vac)

Light Output Average: 13 Watts typical > 4000 FPM

Instantaneous (per flash): 230 mJoule typical

to 4000 FPM

Flash Duration 10-25 microseconds (auto adjust with flash rate)

Flash Tube (Lamp) Life 100 million flashes

Run Time 2 hours typical at 1800 FPM, and over 1 hour at

6000 FPM with fully charged batteries

Charge Time 4-5 hours typical with PSC-pbxU

Weight 1.875 lbs [0.8505 kg] including batteries

This product is designed to be safe for indoor use under the following

conditions (per IEC61010-1).

Operating Temperature 32-104 ºF [0-40 °C]

NOTE: Safety thermal feature will set unit into TACH Mode (stops

flashing) in the event of internal overheating.

Humidity Maximum relative humidity 80% for temperature

up to 88 °F [31 °C] decreasing linearly to 50%

relative humidity at 104 °F [40 °C]

1.0 OVERVIEW

The Phaser-Strobe pbx is an extremely sophisticated instrument with

many features, yet remains simple to operate. Select only the features you

need.

1.1 Display Panel / Definition of Buttons

The display panel consists of

a backlighted liquid crystal

display with six numeric digits

on top and five alphanumeric

digits on the bottom, which

indicate modes, flash rates,

etc. (see Figure 1).

Additional information

displayed include:

PHASEPHASE

PHASE Indicates Phase

Shift Delay Mode

is active

TIME Indicates Phase Shift Time Delay Mode is active

AUTO Indicates Auto Phase Shifting Mode (virtual RPM) is

active

ALT. Indicates alternate function of each button (lower section)

and knob will be used

TACH Tachometer Mode active (strobe won’t flash)

LOCK Unused

EXT External Input Mode active

Figure 1 Display Panel

9.0 SPECIFICATIONS

Internal Mode:

Flash Range 30 - 50,000 FPM (Flashes Per Minute)

Flash Rate Accuracy 0.004% of setting or ±last digit

Flash Rate Resolution 0.01 to 1 FPM (menu selectable), 0.1 FPM

max resolution above 9,999.99 FPM

Display Update Rate Instantaneous

External Modes:

Flash Range and Display same as internal mode - External flash rates

to 0 are acceptable

Tachometer Measurements 5 to 250,000 RPM

Accuracy: ±0.001% of reading or ± last digit

Display Update Rate 0.5 second typical

Trigger to Flash Delay < 5 µsec

Phase Delay Phase: 0.1 to 359.9 degrees, Time: 0.01

to 1000 milliseconds, Auto: 0 to 200

VRPM

External Input TTL Compatible (24V pk max), 500

nanosec min pulse width,

Positive or Negative edge triggered (menu

selectable)

Time Base Ultra Stable Crystal Oscillator

Display LCD display with 6 numeric 0.506 inch

[12.85 mm] high digits and

5 alphanumeric 0.282 inch [7.17 mm] high

digits

Indicators Battery level, On Target, TIME, AUTO, ALT,

TACH, LOCK, and EXT icons

Knob Adjustment Digital Rotary switch with 36 detents per

revolution; velocity sensitive

www.64817.com

On Target Indicator for Tachometer Mode and Remote

Sensor in External Mode

- - - - - Indicates input frequency exceeds the limit of the

stroboscope

Battery indication, see section 8.1

Below the display are six membrane buttons which control the operation

of the Stroboscope. They are:

Multiplies flash rate by 2 times

ALT Function - Starts Menu (See section 3.0)

Hold when powering up to show all segments, then Rev #

and display test

Divides flash rate by 2

Hold when powering up to reset factory defaults

In Internal/External Mode - Toggles display between RPM

and RPS. In External Phase or Time Delay Mode -Cycles

display through RPM, RPS, Phase and Time. In Auto Mode

– Cycles display through RPM, RPS, VRPM and VRPS.

ALT Function - Toggles Tach Mode (flashing) on/off

Manually toggles between Internal and External Modes

ALT Function - Reads and Stores 9 preset flash rates

Activates Alternate Function for buttons (lower section)

and knob

In Internal Mode, toggles between normal flash rate adjust

and “phase” delay adjust

In External Input Mode, cycles through External only (no

delay), Phase, Time and Auto (VRPM) 19

8.3 External Power Supply/Charger

The external power supply/charger (PSC-pbxU) can also be used to

run the stroboscope continuously from the AC mains (115/230 Vac).

To power the strobe with the external power supply/charger (PSC-

pbxU):

1. Plug the power supply/charger cable into the recharger socket

(located below the display panel behind the handle).

2. Plug the power supply/charger into an AC mains wall outlet.

3. Press (and lock) the trigger switch to operate. If the trigger switch

is not pressed, the unit will start charging.

8.4 Battery Disposal

Prior to disposing of the Phaser-Strobe pbx, the user must remove

the Nickel-Metal Hydride batteries. To do this, remove the lens,

reflector and lamp as detailed in the Lamp Replacement section. This

will expose four (4) screws that must be removed so the reflector

housing can be dismantled. There are four (4) additional screws in the

case half opposite the input and output jacks that must be removed.

The case halves can now be separated, exposing the batteries. Remove

the cables from the batteries and place tape over the battery terminals

to prevent them from shorting. The batteries should be sent to a

recycling center or returned to the factory. The rest of the parts may

now be disposed of.

The ALT FUNCTION button toggles ALT. in the display. When ALT. is

displayed, the buttons will perform their secondary function listed in

the lower section of each button. It also changes how the tuning knob

works.

2.0 PREPARATION FOR USE

The Strobe may be hand held or mounted on a tripod or other user supplied

bracket using the ¼-20 UNC bushing at the base of the handle.

2.1 Power

The Phaser-Strobe pbx has internal rechargeable batteries and may

also be powered by an external AC power supply (PSC-pbxU). If

using the internal batteries, the unit should be charged before use (see

section 8.2 Charging the Batteries). The actual operating time of the

stroboscope will depend on the flash rate and duty cycle of operation.

The strobe can also be run continuously from the AC mains with the

power supply supplied (PSC-pbxU, see section 8.3 External Power

Supply/Charger).

2.2 Input / Output Connections

The Phaser-Strobe pbx has input and output jacks on the left side of

the stroboscope. These can be used for external triggering or

synchronization (daisy chaining two or more strobes). These jacks

accept 1/8" (3.5mm) phone plugs (input – stereo, output – mono).

The input and output are TTL compatible. See Figures 2 and 3 for

connector connection detail.

by no flash and the display shows “LO BAT”. At this time the

batteries must be recharged (section 8.2 Charging the Batteries) or

Supply/Charger). Remember to release the trigger switch.

8.2 Charging the Batteries

The unit may be recharged at any time. You do not need to wait until

the low battery condition is indicated.

To charge the Phaser-Strobe pbx with the power supply/charger:

1. Release the trigger so the strobe is off.

2. Plug the recharger cable into the recharger socket (located below

the display panel behind the handle).

3. Plug the recharger into an AC mains wall outlet (115/230 Vac).

CAUTION: Use of rechargers other than the one supplied

(PSC-pbxU) will damage the stroboscope and

void the warranty.

When charging, the strobe will indicate CHRGE in the bottom right of the

display. The recharger will fast charge the batteries for about 4-5

hours and then trickle charge the batteries.

Allow the recharger to charge the batteries until the display shows

DONE for peak battery life performance. If the batteries are not charged

to 100% regularly, the batteries will lose capacity.

The optional ROS-P (Remote Optical Sensor), MT-190P (Magnetic),

or IRS-P (Infrared) sensors may also be used to trigger the unit.

NOTE: When using external sensors that are powered by the Phaser-

Strobe pbx, e.g. Remote Optical Sensor (ROS-P), the sensor

must be plugged in before the stroboscope is turned on, or

the remote sensor may not be powered up.

The input jack (Spointing into socket) enables an external signal to

trigger the strobe. Inserting a plug into the input jack will automatically

put the strobe into the External Mode. When the plug is removed, the

strobe will be put back into the Internal Mode. The Internal Mode can

be forced by pressing the INPUT button. The polarity of the input

pulse can be set in the MENU options.

Pulse Output

from Strobe

Common

(GND)

Common

(GND)

Pulse Output

from Strobe

Figure 3 Output Connector Detail (Mono plug)

Signal Input

+6V Out to

Sensor

Common

(GND)

Common

(GND)

+6V Out to

Sensor

Signal Input

Figure 2 Input Connector Detail (Stereo plug)

8.0 BATTERY AND POWER SUPPLY

SPECIFICS

The Phaser-Strobe pbx is fitted with rechargeable NiMH (Nickel Metal

Hydride) batteries. These batteries contain fewer toxic metals than NiCd

(Nickel Cadmium) and are currently classified “environmentally friendly”.

They also have 30% more capacity than NiCd batteries of the same size.

Like NiCds, NiMH batteries are prone to self-discharge - 10 to 15% of

charge is lost in the first 24 hours then continues at a rate of 0.5 to 1% per

day. For maximum performance, charge the batteries just prior to use.

When not in use, the batteries should be charged at least every three months,

otherwise the battery capacity will be reduced or the batteries may become

unusable.

Charge the batteries before use and allow 3-5 cycles of charging and

discharging for batteries to reach full capacity.

The enclosure contains control electronics to properly and safely charge the

batteries. Never remove the batteries from the enclosure and attempt to

charge externally. Always use the charger supplied (PSC-pbxU).

8.1 Low Battery Indication

When the batteries are charged, there will be no battery indication.

When the batteries are low, the Low Battery icon will blink in the

display. The strobe may still be used for a short time.

Low Battery Icon = Outline blinking (very little time left)

The strobe has a protection feature that prevents the strobe from

operating if the battery voltage is too low. This condition is indicated

With no external input, the output jack (Tpointing away from socket)

provides a TTL compatible pulse from the strobe’s internal oscillator.

If an external input is applied, the output pulse is in sync with the

input pulse. This output pulse may be used to trigger a second

stroboscope synchronously to illuminate larger areas. Many strobes

can be “daisy chained”. The output jack of one strobe is connected to

the input jack of the next strobe causing all the strobes to flash together

and be controlled by the first strobe in the chain. The polarity of the

output pulse can be set in the MENU options.

3.0 MENU

The strobe has a Menu which allows the user to select settings such as

number of decimal places, backlight on or off, positive or negative edge for

input and output signal, and input blanking on or off.

To enter the MENU:

1. Press the ALT FUNCTION button and then the MENU button.

2. SETUP and the menu option will be displayed.

3. Turn the tuning knob to cycle through the main menu options.

4. Once the desired menu option is displayed, press the MENU button to

select it. Press any other button to cancel.

5. Turn the tuning knob to edit the menu option setting.

6. Press the MENU button to save your changes. Press any other button

to cancel.

7. Press any button other than MENU to exit the Main Menu.

8. DONE will be displayed.

4. Reinstall the reflector and then position the front lens in place

matching up the notches on the lens with the two small tabs on

the housing to prevent lens rotation (see Figure 4). Push the tabs

on the front rim outward and press the lens into place.

7.2 Fuse

Under normal operating conditions, the fuse within the stroboscope

should never blow. Examples of abnormal operating conditions would

be foreign materials entering the strobe, such as water, pulp, ink, etc.

The Phaser-Strobe pbx has a resettable fuse, which will reset once

conditions are normal again.

Figure 4 Lamp Replacement

Red Dots

Notches

Below is a list of the menu items:

DECPTDECPT

DECPT- Decimal Point (none, 1 or 2)

BLITEBLITE

BLITE- Backlight (Yes=On or No=Off)

INPUTINPUT

INPUT- Positive (pos) or Negative (neg) Edge for Input Signal

OUTPTOUTPT

OUTPT- Positive (pos) or Negative (neg) Edge for Output Signal

BLANKBLANK

BLANK- Input Blanking (Yes=On or No=Off)

4.0 OPERATION

To turn on the stroboscope, depress and hold the trigger. The trigger may be

locked in position using the side locking button. To lock the stroboscope

on, depress the trigger as far as it will go and then press the locking button.

Once the locking button is set you may release the trigger and the trigger will

be held in place. To unlock the stroboscope, simply depress the trigger and

then release.

There are five operating modes for the Phaser-Strobe pbx. These are Internal,

External Input, External Phase Delay, External Time Delay, and Auto (Virtual

RPM). All but the Internal Mode require an external input signal.

In the Internal Mode the knob adjusts the flash rate. In the External

Input Mode an external signal is used to trigger the flash and the knob has

no effect. The External Delay Modes (Phase, Time and Auto) enable the

user to vary the stopped motion image at any point in the cycle without

having to move the trigger source location.

4.1 Internal Mode - Standard Strobe Operation

In the Internal Mode the stroboscope generates it’s own signals and

functions like a tunable stroboscope. The strobe is in the Internal

Mode when nothing is plugged into the input jack or when manually

set using the INPUT button.

615

The stroboscope is designed to discharge the internal high voltages

within 30 seconds. However, caution should be exercised when replacing

the lamp.

The lamp can be replaced by using just a pocket screwdriver. It is not

necessary to remove any screws to replace the lamp.

To change the lamp:

1. Push apart the two tabs on the side of the reflector housing and

remove the lens using a small screwdriver to help pry one tab and

lift the lens. Take care not to pry the tab any more than is necessary

to free the lens. The reflector is held in place by the front lens and

will come loose, but it is not necessary to remove the reflector.

2. Hold the lamp with a cloth between your forefinger and thumb

and rock it back and forth gently while pulling out. Do not attempt

to rotate the lamp. The lamp is socketed and will come out easily

when pulled straight out.

WARNING: Do NOT touch the new lamp with bare fingers.

3. The lamps are polarized and must be put into the socket matching

polarity. Using a lint free cloth, match up the red dot on the

plug with the red dot on the socket and gently rock the lamp

while pushing it into place (see Figure 4). Make sure the lamp is

in straight and centered in the reflector hole.

CAUTION: Do NOT allow the reflector to contact the lamp.

Table des matières

Autres manuels MONARCH INSTRUMENT Instrument de mesure

MONARCH INSTRUMENT

MONARCH INSTRUMENT Pocket Laser Tach 200 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT PLT200 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro 100 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT PALM STROBE x Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Pocket Laser Tach 200 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT ACT-3X Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT EXAMINER 1000 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro 300 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro 300 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Pocket Laser Tach 200 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Pocket Tach 99 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT RCA Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro 100 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT PLS Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro 100 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT 6235-010 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT ACT-1B Series Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro UV365 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro 100 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT 6180-022 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Strobe dax Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT ACT-1B Series Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT EXAMINER 1000 Manuel utilisateur

MONARCH INSTRUMENT

MONARCH INSTRUMENT Pocket Tach 99 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur