Molex 64005-3400 Manuel utilisateur

AT-2214 Head Crimp Tool

Doc No: ATS-640053400 Release Date: 06-23-03 UNCONTROLLED COPY Pa e 1 of 7

Revision: B Revision Date: 09-30-05

Air Powered

Crimp

Tool Head

Application Tooling

Specification Sheet Order No 64005-3400

Engineering No AT 2214

FEATURES

 Quick-chan e tool head for the 19279-0001 (AT-200)

 A precision user-friendly terminal locator stop holds terminals in the proper crimpin position

SCOPE

Products: Nylon closed end connectors 14 - 22 AWG. This tool head is intended for use in the 19279-0001 (AT-

200) either hand held or with optional bench adapter 19078-0307 (ATBA) and foot switch.

Testing

Mechanical

The tensile test, or pull test, is a means of evaluatin the mechanical properties of the crimped connections. The

followin charts show the UL specifications for various wire sizes. The tensile stren th is shown in pounds and

indicates the minimum acceptable force to break or separate terminal from the conductor. On this style product,

only the readin from the smallest wire AWG is used. See Chart 1.

Wire Size (AWG)

*UL

–

486 C

* UL – 486 C – Closed end connectors and Wire Nuts.

The followin is a partial list of the product part numbers and their specifications that this tool is desi ned to run.

We will be addin to this list and an up to date copy is available on www.molex.com.

Terminal No Terminal Eng No (REF)

Wire Size

Wire Combinations

AWG

mm²

19160

0012

2214

(2.00

0.35)

See

Chart 1

19160

0013

2214

(2.00

0.35)

See Chart 1

19160

0015

2214

(2.00

0.35)

See Chart 1

19160

0016

2214

(2.00

0.35)

See Chart 1

OPERATION

Refer to the instruction manual for the 19279-0001 (AT200) for

mountin this crimp tool head.

3/8 “

AT-2214 Head Crimp Tool

Doc No: ATS-640053400 Release Date: 06-23-03 UNCONTROLLED COPY Pa e 2 of 7

Revision: B Revision Date: 09-30-05

Wire Preparation

Pre-twisted wire not required for OEM applications. For Solid wire (OEM only) strip leads to 3/8 of an inch. Insert

into connector and crimp.

For stranded wire strip leads to approximately 3/4 of an inch. Twist the wire combination even and ti ht. Trim

stripped pre-twisted area to 3/8 of an inch and insert into connector and crimp. For more information follow the

Quality Crimpin Handbook.

CHART 1

Wire Combinations for Nylon

Insulated Closed End Connectors

Part No 19160001 (NC-2214)

Wire Type

Wire Gauge (AWG

)

Rating

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

L only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded

only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Wire Combinations for Nylon

Insulated Closed End Connectors

Part No 19160001 (NC-2214)

Wire Type

Wire Gauge (AWG

)

Rating

Stranded only

UL only

Stranded only

only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded only

UL only

Stranded

only

UL only

Stranded only

UL only

Solid only

UL only

Solid only

UL only

Stranded only

CSA only

Stranded only

CSA only

Stranded only

CSA only

Stranded only

CSA only

Copper

Stranded only

CSA o

nly

Crimping Terminals

1. Hold air crimp tool with the locator as shown in Fi ure 1. Insert

the closed end connector in the locator slot. Make sure that the

shoulder of the connector is restin on the locator plate. The

connector should fit snu ly into the jaws of the crimp tool. See

Fi ure 1.

2. If necessary, adjust the jaws of the tool in the open position so

that the connector does not move or fall out of the jaws. Usin

a 3/32” Allen wrench turn the adjustin screw in the adjustment

block clockwise (CW) to close the jaws. Turn the adjustin

screw counterclockwise (CCW) to open the jaws. See Fi ure 2.

Figure 1

JAWS OPEN

LOCATOR

PRE-TWISTED WIRE

ADJUSTMENT

BLOCK

CONNECTOR

AT-2214 Head Crimp Tool

Doc No: ATS-640053400 Release Date: 06-23-03 UNCONTROLLED COPY Pa e 3 of 7

Revision: B Revision Date: 09-30-05

3. Place pre-twisted wire into closed-end connector. Than press lever (tri er) on air tool. See Fi ure 3. Release

the lever after jaws have fully closed

Caution: Never place fin ers in the tool nests.

4. Remove the crimped connector and inspect for proper crimp location and insulation closure. Molex offers a

Crimp Inspection Handbook for closed barrel industrial product. See our website or contact your sales

en ineer.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the followin

maintenance steps:

1. Remove dust, moisture and other contaminants with a clean

brush, or soft, lint-free cloth.

2. Do not use any abrasive materials that could dama e the tool.

3. Make certain all pins; pivot points and bearin surfaces are

protected with a thin coat of hi h quality machine oil. Do not oil

excessively. This tool was en ineered for durability, but like any

fine piece of equipment it needs cleanin and lubrication for a

maximum service life of trouble-free crimpin . Use a li ht oil,

such as 30 wei ht automotive oil at the oil points shown in Fi ure

4, every 5,000 crimps or monthly will si nificantly enhance the

tool life and ensure a stable calibration.

4. When tool is not in use store the tool in a clean, dry area.

CAUTION: This crimp tool requires a re ulated air supply line with operatin pressure of 60 to 70 PSI. Hi her

pressure may cause dama e to the tool.

Figure 3

LOCATOR

PRE

TWISTED

WIRE

CONDUCTOR PUNCH

CONDUCTOR ANVIL

CONNECTOR

ADJUSTMENT

BLOCK

CONNECTOR

Figure 2

3/32” ALLEN

WRENCH

ADJUSTING

SCREW

JAWS

OPEN

JAWS

LUBRICATION POINTS

(BOTH SIDES) LIGHT OIL

(EVERY MONTH OR

5,000 CRIMPS)

Figure 4

AT-2214 Head Crimp Tool

Doc No: ATS-640053400 Release Date: 06-23-03 UNCONTROLLED COPY Pa e 4 of 7

Revision: B Revision Date: 09-30-05

Tool Calibration

A Certificate of Calibration (See last pa e) was supplied with the

tool. To recalibrate this tool, pin au e measurements should

be taken in each conductor nest and compared to this chart.

The tool should be lubricated prior to recalibration to ensure

consistent measurements.

Wire Range

“X” Dimension

Conductor Crimp

Awg

mm²

Mean

No Go

0.35

2.00

.100

.096

.104

Warranty

This tool is for electrical terminal crimpin purposes only. This tool is made of the best quality materials. All

vital components are lon life tested. All tools are warranted to be free of manufacturin defects for a period of

30 days Should such a defect occur, we would repair or exchan e the tool free of char e. This repair or

exchan e will not be applicable to alter, misused or dama ed tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and toolin .

PIN GAUGE IN

CONDUCTOR CRIMP

“ Confining ” Crimp

AT-2214 Head Crimp Tool

Doc No: ATS-640053400 Release Date: 06-23-03 UNCONTROLLED COPY Pa e 5 of 7

Revision: B Revision Date: 09-30-05

Figure 5

32 X 1/4”

LONG SHCS

PARTS LIST

Item

Order No

Description

Quantity

64005

3400

rimp Tool Head

Figure 5

64005

0120

Air Tool Head, Nose Mount

64001

3475

Locator Assembly

64001

3470

Toolin Kit

Tooling Kit Only

64001

3401

Conductor Punch

64001

3402

Conductor Anvil

AT-2214 Head Crimp Tool

Doc No: ATS-640053400 Release Date: 06-23-03 UNCONTROLLED COPY Pa e 6 of 7

Revision: B Revision Date: 09-30-05

Figure 6

(4)

(2)

(4)

(2)

Parts List (Continued)

Item

Order No

Description

Quantity

64005

0120

Air Tool Head, Nose Mount

Figure 6

64000

0077

Repair Kit (Sprin s, Rods Pivots, Rin s, and

Washers)

N/A

40 by 3 /8”L

SHCS

2**

N/A

M4 by 12LG. Freedrive Pan Head Screw

2**

N/A

3/16” by 3/8” Lon Dowel Pin

1**

** Available from an Industrial supply company such as MSC (1

800

645

7270).

AT-2214 Head Crimp Tool

Doc No: ATS-640053400 Release Date: 06-23-03 UNCONTROLLED COPY Pa e 7 of 7

Revision: B Revision Date: 09-30-05

Air Powered

Crimp

Tool Head

Certificate of Calibration

Order No 64005-3400

Engineering No AT 2214

Tool Order Number_____________________

Tool En . Number______________________

Tool Revision_________________________

Serial Number________________________

Date of Manufacture____________________

Pin Gau e of Conductor Nest/Nests or Slu hei ht if the nest is the “F” Crimp style.

Ran e Conductor Nest # 1 = ____________-- Actual = ______________

Technician ______________

Date of Calibration ______________

Calibration should be done every 5,000 cycles or 3 months.

Tools should be lubricated durin this operation.

Visit our Web site at http://www.molex.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels molex Outils de sertissage

molex

molex 4D Guide de l'utilisateur

molex

molex AT 2200 Manuel utilisateur

molex

molex 63825-6670 Manuel utilisateur

molex

molex 59354 Manuel utilisateur

molex

molex 63825-5500 Guide de l'utilisateur

molex

molex 69008-1100 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 50098 Series Manuel utilisateur

molex

molex 4D Manuel utilisateur

molex

molex 207128 Series Manuel utilisateur

molex

molex 63825-0500 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 63823-8700 Guide de l'utilisateur

molex

molex 63828-0600 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex CR5974 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex CR5905 Manuel utilisateur

molex

molex 63811-8700 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex TPX50-50 Guide de l'utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2063528-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur

molex 64005-3400 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques