Mocka Zed Scooter Manuel utilisateur
Before you use your scooter, read these instructions carefully and
make sure you keep them in a safe place for further reference. WARNING: Always wear a helmet, shoes and
protective equipment and observe all local road rules.
SAFETY RULES:
1. Before every ride, check that the screws and clamping levers are
tight, that the folding mechanism has clicked into position and the
securing lever is locked tight.
2. Do not ride on any slopes.
3. We recommend adult supervision at all times.
4. Do not ride your scooter on the road, and abide with all local laws in
your area. Wear a helmet and footwear at all times when riding.
5. Your scooter is built for riding and not jumping.
6. Do not exceed 100kg.
7. Ride the scooter in flat, clear and dry areas. Avoid water, sand and
loose gravel.
8. Do not ride at night.
9. Please do not modify the scooter.
10. Please regularly check and tighten all parts on your scooter.
Zed Scooter
ASSEMBLY INSTRUCTIONS
1
mocka.co.nz | mocka.com.au
Thank you for your purchase.
Please follow the instructions below for correct assembly.
Overview
10
9
8
7
6
5
4
3
2
1
1. Handlebars
2. Handlebar grips
3. T-Bar
4. Quick release
5. Vertical adjustment
6. Folding mechanism
7. Brake
8. Rear wheel
9. Quick release
10. Front wheel
Zed Scooter
ASSEMBLY INSTRUCTIONS
2
mocka.co.nz | mocka.com.au
Overview
10
9
8
7
6
5
4
3
2
1
1. Handlebars
2. Handlebar grips
3. T-Bar
4. Quick release
5. Vertical adjustment
6. Folding mechanism
7. Brake
8. Rear wheel
9. Quick release
10. Front wheel
Scooter Setup
Open quick release lever (9) and unscrew. Pull and hold the folding
mechanism lever (6) and push handlebar column forward until the
handlebar clicks into position. Then tighten the quick release so that
the lever can be folded down firmly.
Caution - make sure that the quick release lever (9) is always closed, as
shown in [A] on the picture. The lever should never face into the riding
direction otherwise the lever can touch the wheel.
9
6
A
Zed Scooter
ASSEMBLY INSTRUCTIONS
3
mocka.co.nz | mocka.com.au
Open the quick release lever (4) at the handlebar column. Pull out the
upper part with the handlebar until the push button (5) clicks into position.
You can choose between two different heights. Secure the T-Bar (3) with
the quick release (4). Push the grips into the openings at the ends of the
handlebar. Make sure that the push buttons click into position.
RIDING
Control your speed at all times, and ride within your abilities.
BRAKING
When you want to brake, put your foot on the rear brake and apply
pressure.
IMPORTANT: If you are too fast or if the rear wheel has picked up
oil, water, stones etc. then the braking effect can be reduced.
MAINTENANCE & CARE
After using your scooter, thoroughly clean it and if necessary rub the
wheels dry with a cloth. Remove stones or anything else that may
have stuck in the wheels. Dry and clean the ball-bearings regularly
and replace if worn out. Smooth off any sharp edges that may have
resulted from the use of the scooter.
Store inside.
5
4
3
Locking the Handlebar
Zed Scooter
ASSEMBLY INSTRUCTIONS
4
mocka.co.nz | mocka.com.au
Autres manuels Mocka Scooter
Manuels Scooter populaires d'autres marques
First Choice Mobility
First Choice Mobility Roma Medical Corella S741 Manuel utilisateur
Carrera
Carrera impel Manuel utilisateur
Afikim
Afikim Superlight SL-3 Manuel utilisateur
CareCo
CareCo ZOOM Manuel utilisateur
Douglas
Douglas Vespa G.S. Manuel utilisateur
Gazelle
Gazelle with BOSCH System Manuel utilisateur