Mitsubishi Q Series Manuel utilisateur

Series HMI Connection Manual

134 V1.01 Revision November, 2011

Mitsubishi Q Series Ethernet

（Supports QJ71E71 / QJ71E71-B2 / QJ71E71-B5 / QJ71E71-100 Series Module）

HMI Factory Setting:

Baud rate: 192.168.0.1

Controller Station Number: 1025

Control Area / Status Area: D0 / D10

Connection

Standard jumper Cable/ Network Cable without jumper (Auto-detected by HMI)

Definition of PLC Read/Write Address

a. Registers

Format

Type

Word No. (n)

Read/Write Range Data Length Note

Input Xn X0 – X1FF0 Word Hexadecimal,

Output Yn Y0 – Y1FF0 Word Hexadecimal,

Internal Relay Mn M0 – M8176 Word 2

Special Internal Relay Mn M9000 – M9240 Word 3

Link Relay Bn B0 – B1FF0 Word Hexadecimal,

Annunciator Fn F0 – F2032 Word 2

Timer Value TNn TN0 – TN2047 Word

Counter Value CNn CN0 – CN2047 Word

Data Register Dn D0 – D8191 Word

Special Data Register Dn D9000 – D9255 Word

Link Register Wn W0 – W1FFF Word Hexadecimal

b. Contacts

Format

Type

Bit No. (b)

Read/Write Range Note

Input Xb X0 – X1FFF Hexadecimal

Series HMI Connection Manual

V1.01 Revision November, 2011 135

Output Yb Y0 – Y1FFF Hexadecimal

Internal Relay Mb M0 – M8191

Special Internal Relay Mb M9000 – M9255

Format

Type

Bit No. (b)

Read/Write Range Note

Link Relay Bb B0 – B1FFF Hexadecimal

Annunciator Fb F0 – F2047

Timer Contact TSb TS0 – TS2047

Timer Coil TCb TC0 – TC2047

Counter Contact CSb CS0 – CS2047

Counter Coil CCb CC0 – CC2047

NOTE

1) Before using this communication protocol, the user needs to set communication module

via GX Developer programming tools. For more detailed information regarding the

setting method, please refers to Mitsubishi PLC User Manual.

2) The device address must be the multiple of 16.

3) The device address must be the multiple of 16 plus 9000.

Series HMI Connection Manual

Settings

Screen Editor

1. HMI Configuration Setting

136 V1.01 Revision November, 2011

Series HMI Connection Manual

2. PLC Configuration Setting

V1.01 Revision November, 2011 137

GX Developer (V8.35M)

1. Network Parameter MNET/10H Ethernet Settings

Item Setting

Network Type Ethernet

Starting I/O No. 0000

Network No. 1

Group No. 1

Station No. 1

Mode On-line

Series HMI Connection Manual

138 V1.01 Revision November, 2011

2. Operation Settings

Item Setting

Communication Data Code Binary code

Initial Timing Always wait for OPEN

IP Address 192.168.0.1

Send Frame Setting Ethernet (V2.0)

Enable Write at RUN time Enable

TCP Living Confirmation Setting Use the KeepAlive

3. Open Settings

Item Setting

Protocol TCP

Open Method Unpassive

Fixed buffer Send

Fixed buffer communication procedure Procedure exist

Existence confirmation No confirm

Host Station Port No. 0401(HEX)

4. For more detailed information regarding the setting method, please refers to Mitsubishi PLC

User Manual.

Autres manuels pour Q Series

Ce manuel convient aux modèles suivants

Autres manuels Mitsubishi Système d'E/S

Mitsubishi

Mitsubishi AJ65BT-64RD3 Manuel utilisateur

Mitsubishi

Mitsubishi MELSEC Q Series Manuel utilisateur

Mitsubishi

Mitsubishi AJ65BT-68TD Manuel utilisateur

Mitsubishi

Mitsubishi MELESEC-ST Manuel utilisateur

Mitsubishi

Mitsubishi Q68TD-G-H02 Manuel utilisateur

Mitsubishi

Mitsubishi GT15V-75ROUT Manuel utilisateur

Mitsubishi

Mitsubishi CL1Y2-T1D2S Manuel utilisateur

Mitsubishi

Mitsubishi FX3U-16CCL-M Manuel utilisateur

Mitsubishi

Mitsubishi FX2N-2DA Manuel utilisateur

Mitsubishi

Mitsubishi FX2N-10PG Manuel utilisateur

Mitsubishi

Mitsubishi CL1XY2-DTE1D5S Manuel utilisateur

Mitsubishi

Mitsubishi AJ65SBTB2-16R Manuel utilisateur

Mitsubishi

Mitsubishi MELSEC Q Series Manuel utilisateur

Mitsubishi

Mitsubishi FX2N-5A Manuel utilisateur

Mitsubishi

Mitsubishi MELSEC QS Series Manuel utilisateur

Mitsubishi

Mitsubishi FX2N-4AD-TC Manuel utilisateur

Mitsubishi

Mitsubishi AJ65BT-68TD Manuel utilisateur

Mitsubishi

Mitsubishi CL1XY4-DT1B2 Manuel utilisateur

Mitsubishi

Mitsubishi FX-16E-TB/UL Manuel utilisateur

Mitsubishi

Mitsubishi CL2XY16-DTP1C5V Manuel utilisateur

Mitsubishi

Mitsubishi A8GT-50KBF Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur