Mitsubishi Electric DLP FD730U Manuel utilisateur

DLPProjector

FD730U/FD730U-G

Controlling the projector using a personal computer

This projector can be controlled by connecting a personal computer with RS-232C terminal.

PC-controllable functions:

•Turning the power ON or OFF

•Changing input signals

•Inputting commands by pressing the buttons on the control panel and remote control

•Menu setting

Connection

Important:

• Connect the computer with the projector on a one-to-one basis.

• Make sure that your computer and projector are turned off before connection.

• Boot up the computer first, and then plug the power cord of the projector.

(If you do not follow this instruction, the Com port may not function.)

• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.

1. Interface

1.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)

1.2 Communications format

This projector uses RXD, TXD and GND lines for RS-232C control.

PROTOCOL RS-232C

BAUD RATE 9600 [bps]

DATALENGTH 8 [bits]

PARITY BIT NONE

STOP BIT 1 [bit]

FLOW CONTROL NONE

RS-232C

terminal

D-SUB 9-pin D-SUB 9-pin

RS-232C cable SERIAL

123 4 5

6789

Pin Description Pin Description

1 NC 2 RXD

3 TXD 4 NC

5 GND 6 NC

7 RTS 8 CTS

9 NC

2. Control command configuration

The command consists of the address code, function code, data code, ACK/NAK, and end code. The length of the com-

mand varies among the functions.

[Address code] Fixed to 00. (‘30h’ ‘30h’ in the ASCII code)

[Function code] Code unique to each control operation.

[Data code] Data (value) unique to each control operation (Not always indicated.)

[ACK/NAK] Code indicating the NAK return as described below

Fixed to :N (‘3Ah’ ‘3Eh’ in the ASCII code. Not added to ACK.)

[End code] Fixed to .(‘0Dh’ in the ASCII code)

3. Control sequence

• NAK return

In the following cases, the projector returns the command with “:N” added.

(1) Though the command sent from the computer is received by the projector successfully, it cannot be executed

because the projector is in the operation prohibition state.

(2) The data length of the sent command is incorrect or the command is invalid.

• When a command is sent out during the following operations, it may not be executed.

(1) During signal switching

(2) In the process of the auto position

(3) After the power is turned on.

The projector receives no commands for about 20 seconds (or for 2 minutes at the longest if the lamp does not

light up promptly as the life is expiring). In this case, the projector returns the received command with NAK

added.

• The return command is sent out within 1 second at the latest.

• When sending commands successively, wait to receive the return command of the current command before sending

a next command.

• The projector may not receive a command when the splash screen is being displayed immediately after turning on

the power. Use command “00r10” to cancel the splash screen.

• While using the LAN terminals, the LAN functions take precedence.

• For the LAN terminals, the same commands as those for connecting with the TCP/IP (port number 63007) are avail-

able. Note, however, that the response becomes slightly slower than when using the RS-232C terminals. For the use

of LAN terminals, see page 11.

Address code Function code Data code ACK/NAK End code

ASCII ‘30h’ ‘30h’ Function Data ‘3Ah’ ‘4Eh’ ‘0Dh’

Character 00 Function Data :N

Computer Projector Sequence Note

1Send the command from the personal computer

to the projector.

The projector will send a return command after it

receives an end code. If the projector does not receive commands

normally, that is, if the projector is not connected

physically or unable to receive commands, it

does not send out a return command.

The projector sends out a return command within

one second at the latest.

When the received command cannot be

executed, NAK is returned (as described below).

3The personal computer checks the command

and confirms if the sent command has been

received or not.

Use the check command to see if the projector

has executed the command. This projector sends various codes other than

the return code. When having a control

sequence by RS-232C, reject other codes from

the personal computer.

[Example 1] Turning ON the power. (Values enclosed in quotation marks are ASCII codes.):

[Example 2] Selecting VIDEO as the input signal during auto positioning (Values enclosed in quotation marks are

ASCII codes.):

• The flowchart on the next page shows the recommended operating sequence for your reference to create a pro-

gram.

Command sent from the PC Status code returned

from the projector Description

‘30’ ‘30’ ‘21’ ‘0D’

00! Command for POWER ON

‘30’ ‘30’ ‘21’ ‘0D’

00! Command receipt confirmation (Command

echo back)

Command sent from the PC Status code returned

from the projector Description

‘30’ ‘30’ ‘5F’ ‘76’ ‘31’

00_V1 (During auto positioning)

Command for selecting VIDEO as the

input signal is sent out.

‘30’ ‘30’ ‘5F’ ‘76’ ‘31’ ‘3A’ ‘4E’

00_v1:N The command is received by the projector

but cannot be executed. (NAK return)

[RS-232C control flowchart]

[Compatibility with the former models]

To use the RS-232C commands designed for the former models of Mitsubishi projector, by inputting “00COMMAND0”,

the projector responds in the same way as the former models. (No NAK is returned.)

(For the recommended procedure to use the former command systems, see “Controlling the projector using a personal

computer” for FL7000U.)

ITEM Function Data

Character ASCII

Changing the RS-232C command system COMMAND 43h 4Fh 4Dh 4Dh 41h 4Eh 44h 0 (Former command system),

1 (New command system)

0-3

To normal operation 4

Sending “00vST”

Checking response to “00vST”

Sending out command

END

NAK returned

Command sending fails.

No NAK returned

START

Command is sent successfully.

Command is executed successfully.

Awaiting response

from projector

Command is sent successfully.

Command execution fails.

No response for

1 second or longer

Checking execution of

command (sending out

check command)

Check the following.

• Check that the function code is correct.

• Check that the data code is correct.

• Check that the projector is able to issue

the return command.



Check the projector’s operation using

the 00vST command.

Note: In the following cases, NAK is

returned even when the projector is

in normal condition.

• Immediately after the power is

turned on (about 20 seconds to 2

minutes)

• During input switching

• During auto positioning

• During password lock

Check the following.

• Check that the command begins with

“00”.

• The projector is not supplied with AC

power.



Check that AC power cord is

connected.



Turn on the power. (Turn on the circuit

breaker or main switch.)

• Not connected with the projector.



Check that the RS-232C cable is

connected.



Check the RS-232C cable for electrical

discontinuity.

Projector error

Send out “00vER” to check error details.

Recover from error state.

Enter password.

Send out “00PASS****.”

[Method of checking state of projector]

Projector is functioning.

4. Command list

4.1 Operation commands

The operation commands are used for the basic operation setting of this projector. They may not be executed

while the signals are changed. The operation commands have no data codes. (When the commands for input

select are sent while the splash screen is being displayed,the splash screen is only canceled.)

[Example] When setting the input signal to COMPUTER 1. (Values enclosed in quotation marks are ASCII

codes.):

4.2 Reading command diagram

The projectors operating status, such as POWER-ON/OFF and the currently selected input terminal, etc. can be

monitored.

Use the following commands to obtain the values of the items in the INFORMATION menu.

“hhhh” and “mm” represent hours and minutes respectively.

“HHHH” and “VVVV” represent the horizontal and vertical resolutions respectively.

“***.**” represents the vertical frequency(in Hz) or the horizontal frequency (in kHz).

ITEM Function Note

Character ASCII

POWER ON ! 21h This command is invalid for 1 minute after the power is turned off.

POWER OFF " 22h This command is invalid for 1 minute after the power is turned on.

INPUT COMPUTER 1 _r1 5Fh 72h 31h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT COMPUTER 2 _r2 5Fh 72h 32h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT VIDEO _v1 5Fh 76h 31h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT S-VIDEO _v2 5Fh 76h 32h

This command will not be executed in Stand-by mode or when the MUTE is executed.

INPUT HDMI_d15Fh 64h 31h

This command will not be executed in Stand-by mode or when the MUTE is executed.

Command sent from the PC, etc.Status code returned

from the projector Description

‘30’ ‘30’ ‘5F’ ‘72’ ‘31’ ‘0D’

00_r1

Command for setting the input signal to

COMPUTER 1

‘30’ ‘30’ ‘5F’ ‘72’ ‘31’ ‘0D’

00_r1

Command receipt conﬁrmation

(Command echo back)

ITEM IICSAretcarahC

Function Data (Receive) Function Data (Receive)

h13h05h671PvNOREWOP

h03h05h670PvFFOREWOP

INPUT COMPUTER 1 vI r1

76h 49h72h 31h

INPUT COMPUTER 2 vI r2

76h 49h72h 32h

h13h67h94h671vIvOEDIVTUPNI

h23h67h94h672vIvOEDIV-STUPNI

h13h46h94h671dIvIMDHTUPNI

POWER ON/OFF IMPOSSIBLE vPK 0

76h 50h 4Bh 30h

POWER ON/OFF POSSIBLE

vPK 1

76h 50h 4Bh 31h

NO SIGNAL SUPPLIED vSM 0

76h 53h 4Dh 30h

SIGNAL SUPPLIED vSM

76h 49h 64h 31h

ITEM FunctionData (Receive)

Character ASCII

LAMP TIME (LOW) vLE 76h 4Ch 45h hhhhmm

RESOLUTION vRESO 76h 52h 45h 53h 4Fh HHHHxVVVV

VERTICAL FREQUENCYvVFREQ 76h 56h 46h 52h 45h 51h ***.**

HORIZONTAL FREQUENCY vHFREQ 76h 48h 46h 52h 45h 51h ***.**

SYNC. TYPEvSYNCT 76h 53h 59h 4Eh 43h 54h 0 (NO SIGNAL), 1 (Invalid), 3 (3wire),

4 (4wire), 5 (5wire)

Use the following commands to obtain other information.

The PC sends the command without attaching the data codeto it. On the other hand, the projector attaches to

the received command its current operating status as the data code and send it back to the PC.

[Example] When checking the currently selected input terminal (when the INPUT VIDEO is being selected).

(Values enclosed in quotation marks are ASCII codes.):

4.3 Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash

screen is being displayed, the splash screen is only canceled.)

The remote commands allow the computer to control the projector in the same way as by the remote control.

(Some operations cannot be controlled.) The remote commands have no data codes.

ITEM FunctionData (Receive)

Character ASCII

Model name vMDL 76h 4Dh 44h 4Ch ****************(within 16 characters)

Input source vSOUCE 76h 53h 4Fh 55h 43h 45h r1 r2 v1 v2 d1

Projector status vST 76h 53h 54h 0 (Stand-by mode),

1 (Within 1 minute after POWER-ON (warm-up mode)),

2 (POWER-ON mode (including state of warning)),

3 (Cooling mode),

4 (Abnormal state (including shutdown due to an error)),

5 (State of functioning (menu display, dialog display, AV

MUTE, MAGNIFY, FREEZE, etc.)),

6 (Awaiting password entry)

Error statusvER 76h 45h 52h Reading out error data (3 digits, hexadecimal numbers,

total 9 bits)

(MSB) xb1, xb2... xb8, xb9, 0, 0, 0 (LSB)

xb1: Fan error

xb2: Lamp error (The lamp goes out or does not light.)

xb3: Lamp warning 1 (The lamp life has expired.)

xb4: Lamp warning 2 (The lamp life is expiring.)

xb5: Temperature error

xb6: The temperature warning is being indicated.

xb7: Lamp cover open error

xb8: Fixed to 0.

xb9: States of other component abnormality

Command sent from the PC, etc.Status code returned

from the projectorDescription

‘30’ ‘30’ ‘76’ ‘49’ ‘0D’

00vl

Command for checking the input

terminal

‘30’ ‘30’ ‘76’ ‘49’ ‘76’ ‘31’ ‘0D’

00vlv1

Check result (VIDEO)

Button’s name on remoteFunction

Character ASCII

+/VOLUMEr0672h 30h 36h

-/VOLUME r0772h 30h 37h

KEYSTONE r43 72h 34h 33h

MAGNIFY r02 72h 30h 32h

AV MUTEra672h 61h 36h

r5372h 35h 33h

r2b72h 32h 62h

←r4f72h 34h 66h

→r5972h 35h 39h

h43h53h2745rUNEM

h03h13h2701rRETNE

AUTO POSITIONr0972h 30h 39h

h43h16h274arEZEERF

h83h16h278arEFFICIENT MODE

h23h56h272erTCEPSA

[Example] When displaying the MENU selection bar. (Values enclosed in quotation marks are ASCII codes.):

4.4 Direct commands (Not executable in stand-by mode. Possible only to read during muting.)

The direct commands are used to numerically adjust the volume and keystone.

When the computer sends the command without adding the setting value, the projector returns the received com-

mand with the current setting value added as a data code.

How to set the value

Use the character or ASCII code as shown below to set the value.

[Example] When setting the volume to 15. (Values enclosed in quotation marks are ASCII codes.):

4.5 Function commands (Not executable in stand-by mode. When the mute commands are sent while the splash

screen is being displayed, the splash screen is only canceled.)

The mute commands are used for the mute setting of this projector with the 0 (HEX: 30h) and 1 (HEX: 31h).

4.6 Menu setting commands (Not executable in stand-by mode. Possible only to read during muting.)

The menu setting commands are used for the menu setting of this projector. If the personal computer sends the

command without attaching the data code, the projector attaches to the received command its current setting

value as the data code and send it back to the PC.

Command sent from the PC, etc.Status code returned

from the projector Description

‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’

00r54

Command operating the same as the

MENU button

‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’

00r54

Command receipt conﬁrmation

(Command echo back)

ITEM FunctionData

Character ASCII

VOLUME VL 56h 4Ch00-21

KEYSTONE (vertical) KS 4Bh 53h ± 51

Character + - 0123456789

ASCII‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’

Command sent from the PC, etc.Status code returned

from the projector Description

‘30’ ‘30’ ‘56’ ‘4C’ ‘31’ ‘35’ ‘0D’

00VL15

Command for setting the volume

‘30’ ‘30’ ‘56’ ‘4C’ ‘31’ ‘35’ ‘0D’

00VL15

Command receipt conﬁrmation

(Command echo back)

ITEM FunctionData

Character ASCII

AV MUTEMUTE 4Dh 55h54h 45h 0 (OFF), 1 (ON)

)NO(1,)FFO(0hA5h25h64ZRFEZEERF

Function canceling FNCOFF 46h 4Eh 43h 4Fh 46h 46h

ITEM FunctionData

Character

ASCII

COLOR ENHANCER CE 43h 45h 0 (AUTO), 1 (PRESENTATION), 2 (STANDARD),

3 (THEATER), 4 (USER)

COLOR ENHANCER-

USER-GAMMA MODE

CEU1GS43h 45h 55h 31h 47h 53h 0 (DYNAMIC), 1 (NATURAL), 2 (DETAIL)

COLOR ENHANCER-

USER-Brilliant Color

CEU1B 43h 45h 55h 31h 42h 00-10

COLOR ENHANCER-

USER-RGB-COLOR

CEU1C 43h 45h 55h 31h 43h ±10

COLOR ENHANCER-

USER-RGB-TINT

CEU1T 43h 45h 55h 31h 54h ±10

CONTRAST PP 50h 50h ±30

BRIGHTNESS QQ 51h 51h ±30

COLOR TEMP. A 41h 1 (STANDARD), 2 (HIGH), 3 (LOW), 4 (USER)

COLOR TEMP.-USER

(CONTRAST)P50h ±30 ±30 ±30 (R, G, B)

COLOR TEMP.-USER

(BRIGHTNESS)Q51h ±30 ±30 ±30 (R, G, B)

COLOR T 54h ±10

TINT S 53h ±10

SHARPNESS R 52h ±05

NOISE REDUCTION NR 4Eh 52h 0 (OFF), 1 (ON)

CTI CTI 43h 54h 49h 0 (OFF), 1 (ON)

INPUT LEVEL IPL 49h 50h 4Ch ±5,

CLOSED CAPTION CC 43h 43h 0 (OFF), 1 (CC1), 2 (CC2)

WALL SCREEN WS 57h 53h 0 (OFF), 1 (BEIGE), 2 (LIGHT BLUE),

3 (LIGHT GREEN), 4 (PINK), 5 (BLACK BOARD),

6 (WHITE BOARD)

WALL SCREEN (BEIGE) WSY 57h 53h 59h 1-5

WALL SCREEN

(LIGHT BLUE) WSB57h 53h 42h 1-5

WALL SCREEN

(LIGHT GREEN)WSG57h 53h 47h 1-5

WALL SCREEN (PINK)WSP57h 53h 50h 1-5

LAMP MODE LM 4Ch 4Dh 0 (STANDARD), 1 (LOW)

STANDBY MODE STBY53h 54h 42h 59h 0 (STANDARD), 1 (LOW)

AUDIO INPUT AUDIO41h 55h 44h 49h 4Fh 0 (AUTO), 1 (IN1), 2 (IN2), 3 (IN3), 4 (MIX)

AUTO POWER ON APON41h 50h 4Fh 4Eh 0 (OFF), 1 (ON)

AUTO POWER OFF APOF41h 50h 4Fh 46h 00 (OFF), 05, 10, 15, 30, 60

SPLASH SCREEN SS 53h 53h 0 (OFF), 1 (ON)

AV MUTE MODE MM 4Dh 4Dh 0 (BLACK), 1 (IMAGE)

BACK COLOR BB 42h 42h 0 (BLACK), 1 (BLUE)

IMAGE REVERSE IR 49h 52h0 (OFF), 1 (MIRROR), 2 (INVERT),

3 (MIRROR INVERT)

TEST PATTERN TP

54h 50h0(OFF), 1(CROSS HATCH), 2(WHITE), 3(BLACK)

ASPECT SC 53h 43h0(AUTO), 1(16:9(FULL)), 2(NATIVE)

PASSWORD FUNCTION PSLOCK50h 53h 4Ch 4Fh 43h 4Bh 0**** (UNLOCK), 1**** (DISPLAY INPUT),

2**** (MENU ACCESS), 3**** (SPLASH SCREEN),

**** is a 4 to 8-digit password comprised of any

ﬁgures 1 to 4.

MENU POSITION MP 4Dh 50h 0 (Upper left), 1 (Lower right)

CINEMA MODECINE43h 49h 4Eh 45h 0 (OFF), 1 (AUTO)

VIDEO SIGNAL

(VIDEO only)VS 56h 53h 0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM), 4

(4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)

SET UP STU53h 54h 55h 0 (AUTO), 1 (OFF), 2 (3.75%), 3 (7.5%)

LANGUAGE LG 4Ch 47h 00 ( ), 01 (English), 02 (Español), 03

(Deutsch), 04 (Français), 05 (Italiano), 06 ( ),

07 ( ),

08 ( ), 09 (PORTUGUÊS), 11

(SVENSKA), 12 (POLSKI)

RESET ALL RSTALL52h 53h 54h 41h 4Ch 4Ch

MEMORY CALLMMC 4Dh 4Dh 43h 0 (AUTO) , 1 (MEMORY 1), 2 (MEMORY 2)

HORIZ.POSITION HP 48h 50h+ (increment), - (decrement)

ITEM Function Data

Character

ASCII

*1) Setting range differs depending on the input signals.

• Some commands are not executed depending on the input signal. The operational restrictions same as those

on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

How to set the value

Use the character or ASCII code as shown below to set the value.

[Example 1] When setting the AUTO POWER ON to ON. (Values enclosed in quotation marks are ASCII codes.):

[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and

the CONTRAST B to -5. (Values enclosed in quotation marks are ASCII codes.):

[Example 3] When checking the TINT setting (when the TINT is set to +10). (Values enclosed in quotation marks

are ASCII codes.):

VERT. POSITION VP 56h 50h + (increment), - (decrement)*1

FINE SYNC. FN 46h 4Eh 00-31

TRACKING TRK 54h 52h 4Bh + (increment), - (decrement)*1

COMPUTER INPUT CIN 43h 49h 4Eh 0 (RGB), 1 (YCBCR/YPBPR), 2 (AUTO)

OVER SCAN VOS 56h 4Fh 53h 00 (90%) - 10 (100%)

HOLD HLD 48h 4Ch 44h 0 (OFF), 1 (ON)

HOLD BEGIN HLB 48h 4Ch 42h 00-99

HOLD END HLE 48h 4Ch 45h 00-99

CLAMP POSITION CLP 43h 4Ch 50h 001-255

CLAMP WIDTH CLW 43h 4Ch 57h 01-63

VERT. SYNC VSC 56h 53h 43h 0 (AUTO), 1 (OFF)

LPF LPF 4Ch 50h 46h 0 (OFF), 1 (ON)

SHUTTER(U) SHU 53h 48h 55h 00-20

SHUTTER(L) SHL 53h 48h 4Ch 00-20

SHUTTER(LS) SHLS 53h 48h 4Ch 53h 00-20

SHUTTER(RS) SHRS 53h 48h 52h 53h 00-20

Character+-0123456789

ASCII ‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’ ‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’

Command sent from the PC, etc. Status code returned

from the projector Description

‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’

00APON1 Command for setting the AUTO

POWER ON to ON

‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’

00APON1 Command receipt confirmation

(Command echo back)

Command sent from the PC, etc. Status code returned

from the projector Description

‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’

00P+10+00-05 Command for setting the picture

control

‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’

00P+10+00-05 Command receipt confirmation

(Command echo back)

Command sent from the PC, etc. Status code returned

from the projector Description

‘30’ ‘30’ ‘53’ ‘0D’

00S Command for checking the TINT

setting

‘30’ ‘30’ ‘53’ ‘2B’ ‘31’ ‘30’ ‘0D’

00S+10 Check result (+10)

ITEM Function Data

Character

ASCII

[Example 4] When setting the GAMMA MODE of the COLOR ENHANCER-USER to DETAIL. (Values enclosed

in quotation marks are ASCII codes.):

4.7 Password lock commands

The password lock commands control the password lock. The password lock enabling or disabling command is

sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the

password lock is enabled or disabled successfully, the projector sends a return command comprising the data

code, password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command

with “0” at the end. There is no reconfirmation of the password. The password input command is for enabling pro-

jection of image when password lock has been set to DISPLAY INPUT. The password input command is sent with

a 4 to 8-digit password comprised of any figures 1 to 4 at the end.

**** is a 4 to 8-digit password comprised of any figures 1 to 4.

[Example] When enabling the password lock of DISPLAY INPUT (in the case that the password is 123412):

Command sent from the PC, etc. Status code returned

from the projector Description

‘30’ ‘30’ ‘43’ ‘45’ ‘55’ ‘31’ ‘47’ ‘53’ ‘32’ ‘0D’

00CEU1GS2 Command for setting the picture

control

‘30’ ‘30’ ‘43’ ‘45’ ‘55’ ‘31’ ‘47’ ‘53’ ‘32’ ‘0D’

00CEU1GS2 Command receipt confirmation

(Command echo back)

ITEM Function Data

Character ASCII

Password lock enabling/

disabling PSLOCK 50h 53h 4Ch 4Fh 43h 4Bh 0**** (Disabling), 1**** (DISPLAY INPUT), 2****

(MENU ACCESS),

3**** (SPLASH SCREEN)

Password input PASS 50h 41h 53h 53h ****

Command sent from the PC, etc. Status code returned

from the projector Description

‘30’ ‘30’ ‘50’ ‘53’ ‘4C’ ‘4F’ ‘43’ ‘4B’ ‘31’ ‘31’ ‘32’ ‘33’ ‘34’ ‘31’ ‘32’ ‘0D’

00PSLOCK1123412 Command for enabling the

password lock of DISPLAY INPUT

‘30’ ‘30’ ‘50’ ‘53’ ‘4C’ ‘4F’ ‘43’ ‘4B’ ‘31’ ‘31’ ‘32’ ‘33’ ‘34’ ‘31’ ‘32’ ‘31’ ‘0D’

00PSLOCK11234121 Response informing that the

projector succeeded in enabling

the password lock of DISPLAY

INPUT

Autres manuels pour DLP FD730U

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mitsubishi Electric Projecteur

Mitsubishi Electric

Mitsubishi Electric WD2000U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HC4000 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD360U-EST Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EX52U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HC5000 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD600U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XL7100U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HC3000 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FL6900U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric DLP HC910 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric DLP FD730U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric WD8200U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD50U MINI-MITS Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EX52U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD470U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric DLP EX321U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD210U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric WD385U-EST Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric ColorView XD300U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XL2550U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric HC5500 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MH2850U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric TW21U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD205U Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur