Mircom MS-400MP Series Manuel utilisateur
www.mircom.com LT-6660 Rev. 3 July 2020
MS-400MP(U) Series
Fire Alarm Manual Station
1
Mircom’s MS-400MP(U) Series Fire Alarm Manual Stations
provide manual fire alarm activation. These high quality, extruded
aluminum stations are available as one stage or two stage
stations. On the two stage model, a keyswitch allows the
activation of the stage two alarm. Each station has a permanently
attached MP (Mircom Protocol) addressable module which is
configured with a tool (see LT-6146 MIX-4090 Device
Programmer for instructions).
Specifications & Dimensions
Compatible with Mircom Fire Alarm Control Panels
Electrical Rating:
• Nominal Operating Voltage: 15-30 VDC
• Maximum alarm current: 3.3 mA
• Standby current: 2 mA
Dimensions of aluminum body:
• 4.525” H x 3.3” W x 0.762” D
Installing the manual station
This guide covers these models:
• MS-401MP(U) Intelligent Single Stage Manual Station MP
• MS-402MP Intelligent Two Stage Manual Station MP
• MS-407MP(U) Intelligent Single Stage Manual Station MP
with additional N.C. switch
The suffix Uindicates a USA version.
Contents of kit
• MS-401MP(U), MS-407MP(U): 2 mounting screws
• MS-402MP: 2 mounting screws, 2 stage two keys
Sold separately
• Plastic rod or break glass (Mircom part number GL-004K)
A. Wiring
Note: The maximum wire size is 12 AWG.
1. Connect the black (−) wire from the previous station to
the terminal that is connected to the black (−) wire from
the addressable module.
2. Connect the black (−) wire leading the next station to the
other side of the terminal that is connected to the black
(−) wire from the addressable module.
Note: The wires must be on opposite sides of the set screw.
Refer to Figure 2 for the location of the wires.
3. Tighten the (−) terminal.
4. Connect the red (+) wire from the previous station to the
terminal that is connected to the red (+) wire from the
addressable module.
5. Connect the red (+) wire leading to the next station to the
other side of the terminal that is connected to the red (+)
wire from the addressable module.
Note: The wires must be on opposite sides of the set screw.
Refer to Figure 2 for the location of the wires.
6. Tighten the (+) terminal.
Figure 1: Wiring Diagram
Figure 2: Close-up of terminals showing correct wiring
Notes
• Wire as shown so that supervision of connections is
maintained.
• Maximum wire size: 12 AWG
• All manual fire alarm stations shall be installed as per the
specific requirements outlined in the UL/ULC codes, as well
as all other applicable national or local codes.
• Final acceptance is subject to the local authority having
jurisdiction.
}
−
−
+
+
TO NEXT STATION OR END
OF LINE DEVICE
FROM
PREVIOUS
STATION
AUXILIARY FUNCTION
NORMALLY CLOSED SWITCH
(MS-407MP(U) ONLY)
{
{
−
BLACK
+RED
ADDRESSABLE
MODULE
TO ADDRESSABLE
MODULE
WRONG: BOTH
WIRES ON THE
SAME SIDE OF
THE SET SCREW
TO ADDRESSABLE
MODULE
CORRECT: BOTH
WIRES ON
OPPOSITE SIDES
OF THE SET SCREW
X
Canada
25 Interchange Way
Vaughan, ON L4K 5W3
Tel: 1-888-647-2665
U.S.A
4575 Witmer Industrial Estates
Niagara Falls, NY 14305
Tel: 1-888-647-2665
MS-400MP(U) Series
Fire Alarm Manual Station
www.mircom.com LT-6660 Rev. 3 July 2020
2
B. Setting the addressable module
Follow the instructions in LT-6146 MIX-4090 Device Programmer.
The factory default address is 255.
C. Mounting
1. Pull down the handle so that the station is open.
2. Mount the station to a surface mounted box with the 2
included screws. Refer to Figure 3.
3. Close the station. Follow the instructions under
Resetting the manual station on this page.
Figure 3: Mounting the manual station
Using the manual station in
case of fire
Activating the alarm
• Pull down the handle.
The handle is now hanging down. A qualified person must
reset the station. See Resetting the manual station.
Activating the stage two alarm (MS-402MP only)
1. Insert the stage two key into the keyhole inside the station,
and then turn the key. This keyhole is accessible only after
the alarm handle has been pulled.
The stage two alarm activates immediately.
Note: The stage two alarm will activate automatically a certain
amount of time after the handle has been pulled if no
action is taken. This time is set in the Fire Alarm Control
Panel.
Resetting the manual station
Note: Resetting the station does not cancel the alarm at the
panel.
1. Insert a small flathead screwdriver into the hole in the front of
the handle. Make sure that the end of the screwdriver is
resting on top of the latch inside the station. The screwdriver
must push down this latch order for the handle to close.
2. Close the handle and at the same time, move the handle of
the screwdriver up. See Figure 4.
As you close the handle, the screwdriver acts as a lever to
push the latch down, allowing the handle to close.
You will hear a click when the handle is closed and the station
is reset.
3. Insert the plastic rod (break glass) into the hole on the right
side. See Figure 4.
4. Reset the Fire Alarm Control Panel to cancel the alarm.
Figure 4: Resetting the manual station
MANUAL STATION SINGLE GANG BOX
SCREW
SCREW
Ce manuel convient aux modèles suivants
6
Autres manuels Mircom Alarme incendie
Mircom
Mircom MPS-800MPU Series Manuel utilisateur
Mircom
Mircom FleX-Net BBX-1024DS Guide de l'utilisateur
Mircom
Mircom MPS-800MP Series Manuel utilisateur
Mircom
Mircom FleX-Net FX-2003-12NDS Manuel utilisateur
Mircom
Mircom RAM-300LCD Series Manuel utilisateur
Mircom
Mircom MPS-800 Series Manuel utilisateur
Mircom
Mircom FleX-Net FX-4000 Manuel utilisateur
Mircom
Mircom MPS-800MP Series Manuel utilisateur
Mircom
Mircom flexnet Manuel utilisateur
Mircom
Mircom MS-700ID SERIES Manuel utilisateur
Mircom
Mircom FA-1000 SERIES Manuel utilisateur
Mircom
Mircom FX-350 Series Manuel utilisateur
Mircom
Mircom QX-mini Manuel utilisateur
Mircom
Mircom FleXNet FNC-2000 Manuel utilisateur
Mircom
Mircom FX-350 Series Manuel utilisateur
Mircom
Mircom MS-700AP Series Manuel utilisateur
Mircom
Mircom RAM-300LCD Series Manuel utilisateur
Mircom
Mircom FA-102T Manuel utilisateur
