Minuteman MC20115 Mode d’emploi

Model:

MC20115

MC20230

MC20230CE

OPERATION SERVICE PARTS CARE

200 Floor

Scrubber

Electric

Revised 8/03

TABLE OF CONTENTS

Page

Safety Instructions ............................................. 1

Electrical Requirements ................................... 2

Control Panel Identification ................................ 3

Brush Installation Instructions ............................. 4

Operating Instructions/Maintenance ................... 5

Main Polyethylene Components ........................ 6 - 7

Solution/Recovery Tank ..................................... 8 - 9

Vacuum Components ........................................ 10 - 11

Brush Drive Assemblies .................................... 12 - 13

Back Panel ....................................................... 14 - 15

Squeegee Assembly ......................................... 16 - 17

Wiring Diagram................................................. 18

FOR COMMERCIAL USE ONLY

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the

following:

READ ALL INSTRUCTIONS BEFORE USING

WARNING - To reduce the risk of fire, electric shock, or injury:

Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing,

cleaning or maintaining.

WARNING

To reduce the risk of electric shock - Do not expose to rain. Store indoors.

•Do not allow to be used as a toy. Close attention is necessary when used by or near children.

•This machine shall be used only by instructed and authorized persons.

•Use only as described in this manual. Use only manufacturer’s recommended attachments.

•Inspect cord regularly. Do not use with damaged cord or plug. If appliance is not working as it

should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service

center. Use only cord specified by manufacturer.

•Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp

edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

•Do not handle plug or appliance with wet hands.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,

hair, and anything that may reduce airflow.

•Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

•Do not use without dustbag and/or filters in place.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Do not use to pick up flammable or combustible liquids such as gasoline or use in areas they may

be present.

•Connect to a properly grounded outlet only. See grounding instructions.

•This machine is not suitable for picking up hazardous dust.

•Close tank and lid before use.

SAVE THESE INSTRUCTIONS

INSPECTION

Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly

inspected before shipment and any damage is the responsibility of the delivering carrier who should

be notified immediately.

WARNING

• Read Instruction Manual before operating this piece of equipment.

• To reduce the risk of fire, use only commercially available floor cleaners and waxes intended for

machine application.

• To reduce the risk of electrical shock, do not expose to rain. Store indoors.

• Do not cross over supply cord, hazard exists when rotating brush passes over cord.

• Electrical motors and components can cause an explosion when operated near volatile materials

and vapors. Do not use this machine near flammable materials such as solvents, thinners, fuels,

grain dust, etc.

ELECTRICAL

(Model MC20115) This floor machine is designed to operate on a standard 15 amp. 120 volt, 60 hz,

AC circuit. Voltages below 105 volt AC or above 125 volts AC could cause serious damage to the

motor.

(Model MC20230) This machine is designed to operate on a standard 16 amp type L fused 230 volt,

50 hz, AC circuit. Voltages below 200 volts AC or above 250 volts AC could cause serious damage

to the motor I.E.C. Class 1.

GROUNDING INSTRUCTIONS

• This floor finishing machine should be grounded while in use to protect the operator from electric

shock. The machine is equipped with a three-prong grounding type attachment plug to fit the proper

grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding

wire. Never connect this wire to other than the grounding blade.

• Floor finishing machines rated less than 150 volts — If the machine is provided with an attachment

plug as shown in Sketch A it is intended for use on a 120-volt (nominal) circuit. If a properly grounded

receptacle as shown in Sketch A is not available, an adapter as shown in Sketch C is available and

should be installed as shown in Sketch B if the outlet box that houses the receptacle is grounded.

Be sure to fasten the grounding tab with the faceplate screw.

1. Vacuum switch 7. Foot pedal for lower/raising brush

2. Squeegee lift lever 8. Squeegee

3. Brush switch 9. Squeegee pitch control

4. Solution control lever 10. Recovery hose

5. Power connection cable 11. Recovery tank dump hose

6. Power assist control 12. Solution tank dump hose

SQUEEGEE PITCH CONTROL ADJUSTMENTS

Some minor adjustments may be required due to floor

types and conditions to extend downward travel. Remove

clevis pin (3) and unscrew yoke (1) from cable (2). To

adjust pitch (angle) of squeegee, loosen bolts (5) and

knobs (4). Squeegee angular position can now be

changed for best performance.

BRUSH INSTALLATION - REMOVAL

INSTALLATION - Figure 1

1. Disconnect power cable (mains) from machine.

2. Set brush assist lever (A) to rabbit.

3. Raise brush mechanism (B) to the “up” position by depressing pedal downward as shown.

4. Remove side skirt (C) by lifting up and away.

5. Center brush (D) under machine as shown lining up center

hex drive hub.

6. By releasing foot pedal (B) to lower brush mechanism, drive hub will engage.

REMOVAL - Figure 2

1. Disconnect power cable (mains) from machine.

2. Set brush assist lever (A) to rabbit.

3. Raise brush mechanism (B) to “up” position by depressing pedal downward as shown.

4. Remove side skirt (C) by lifting up and away.

5. Brush has snap-on push-off clutch plate. By pushing brush away from machine and from side it

will release brush assembly.

Fig. 1 Fig. 2

OPERATING INSTRUCTIONS

1. Filling: Fill the solution tank with the desired amount of water and add liquid cleaning solution to

the proper dilution ratio. DO NOT USE powdered cleaning chemicals. Powders are unlikely to

dissolve thoroughly, resulting in clogging the in-line solution filter. This can reduce or stop water

flow to the brush.

2. Lower brush assembly.

- To lower the brush, first push the pedal slightly towards the center of the machine

(unlock it), then release it slowly.

- To lift the brush, press the pedal down until lift mechanism engages.

3. Turn on brush switch.

4. Adjust solution control feed lever.

5. Turn on vacuum switch.

6. Lower squeegee assembly.

After Use:

1. Turn off solution feed.

2. Switch off brush and raise.

3. Raise squeegee assembly.

4. Turn off vacuum motor.

Solution and recovery tanks should be emptied after every use.

MAINTENANCE: Unplug from outlet before servicing.

Daily 1. Clean float assembly & squeegee blades.

Monthly 1. Check wear on squeegee blades.

2. Grease rear wheels.

3. Grease pivot points on brush motor assembly.

Every 500 hours check condition of carbon brushes on vacuum motor and

brush drive motor.

Parts List

Item Part No. Qty. Description

1 210002 1 Lid Assembly Recovery

2 210001MCH 1 20" Solution/Recovery Tank Assembly

3 210000MCH 1 20" Base Assembly

4 210004 1 Recovery Dome

5 210006 2 Lid Gasket

6 210007 2 Lid Gasket

7 712565 10 SCR-MC 1/4-20 x .62 SS

8 711106 25 SCR-ST-A 10 x .75 PL

9 430044MCH 2 Hinge Lid 20"

10 712810 4 SCR-MC 10-24 x .37 STPL

11 712536 6 SCR-MC 10-24 x .62 SS TH

12 210005 1 Dome Gasket

13 260087 1 Hinge

14 450066 1 Solution Tank Cover

15 210055 1 Side Skirt Retainer

16 210052 1 Splash Skirt

17 210056 1 Skirt Retainer Front

18 210053 1 Skirt at Access Panel

19 210057 1 Skirt Retainer at Access Panel

20 210058 1 Skirt Retainer at Wheel

21 210054 1 Skirt at Wheel

22 210059 1 Access Panel

23 833214 1 Knob 3-Sided

24 450062 1 Cord, Nylon

25 210061 1 Pocket Pull

26 430126 2 Hinge Backing Plate

27 715089 1 Decal “200”

28 715060 1 Decal “Minuteman”

29 712822 5 No. 10-24 x .50 Lg. Screw

30 712900 5 Nut-Hex 10-24 STPL

31 210063 1 Access Panel Hanger

32 210027 2 Magnetic Catch

33 833463 1 Titl. Cable

34 712042 1 5/16-18 x .62 Wizz Bolt HH

35 711533 5 WSR-Internal Lock #10

36 712540 6 SCR-MC 10-24 x .37 SS TR

37 210077 1 Skirt

38 210078 1 Retainer

39 711104 3 SCR-ST 10 x .50

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Minuteman Scrubber

Minuteman

Minuteman Port A Scrub 12 Battery Guide de configuration

Minuteman

Minuteman Max Ride MR20ECO Manuel utilisateur

Minuteman

Minuteman E33XL Manuel utilisateur

Minuteman

Minuteman E17 Manuel utilisateur

Minuteman

Minuteman E28 Manuel utilisateur

Minuteman

Minuteman m12110 Manuel utilisateur

Minuteman

Minuteman E17 Manuel de la liste des pièces

Minuteman

Minuteman E45 Series Manuel utilisateur

Minuteman

Minuteman Ambassador 20 Manuel de la liste des pièces

Minuteman

Minuteman ES260 Mode d’emploi

Minuteman

Minuteman M14100 Mode d’emploi

Minuteman

Minuteman E20 SPORT Manuel utilisateur

Minuteman

Minuteman 200X Mode d’emploi

Minuteman

Minuteman SCV28 Mode d’emploi

Minuteman

Minuteman ES2832 Manuel utilisateur

Minuteman

Minuteman E17 Manuel utilisateur

Minuteman

Minuteman Port A Scrub 14 Manuel utilisateur

Minuteman

Minuteman ERide 21 Manuel utilisateur

Minuteman

Minuteman MC20000CE Mode d’emploi

Minuteman

Minuteman E17 Manuel utilisateur

Minuteman

Minuteman Scrubmaster B5 Manuel utilisateur

Minuteman

Minuteman E17TD Manuel utilisateur

Minuteman

Minuteman E17 Manuel utilisateur

Minuteman

Minuteman 380 Mode d’emploi

Manuels Scrubber populaires d'autres marques

Olympus

Olympus M200H Manuel utilisateur

Clarke

Clarke BEXT 100H Manuel d'installation et d'exploitation

JOHNY VAC

JOHNY VAC JVC70BCT Manuel utilisateur

RCm

RCm Elan Series Manuel

Kärcher

Kärcher B 120 W Manuel utilisateur

Truvox

Truvox Orbis MotorScrubber 20 Manuel utilisateur

Numatic

Numatic TTB 4045/100 Manuel utilisateur

U.S. Products

U.S. Products PEX 500-C-TICK Mode d'emploi

Mclennan

Mclennan C510 Manuel utilisateur

Tennant

Tennant T20 LPG Manuel utilisateur

Columbus

Columbus ARA 66 BM 100 Manuel utilisateur

Numatic

Numatic TTV 678G / 300T Manuel utilisateur

American-Lincoln

American-Lincoln 505-945 Manuel utilisateur

FIORENTINI

FIORENTINI ET 65-75 Manuel utilisateur

Floorpul

Floorpul ruby 48 blt Guide de l'utilisateur

Onyx

Onyx RX-34 Manuel utilisateur

Dustbane

Dustbane Hurricane 400 Manuel utilisateur

Sana

Sana EUJ-702 Manuel utilisateur