Minuteman MC17000QP Mode d’emploi
170 Automatic170 Automatic
170 Automatic170 Automatic
170 Automatic
Floor ScrubberFloor Scrubber
Floor ScrubberFloor Scrubber
Floor Scrubber,,
,,
,
BatterBatter
BatterBatter
Batteryy
yy
y
Model: MC17000QP
MC17000-00CE
Revised 8/03
OPERATION SERVICE PARTS CARE
TABLE OF CONTENTS
Page
Safety Instructions ...................................................................................... 1
Electrical Requirements ............................................................................. 2
Control Panel Identification ......................................................................... 3
Brush Installation Instructions ..................................................................... 4
Operating Instructions/ Maintenance .......................................................... 5
Main Polyethelene Components ................................................................. 6 - 7
Solution/Recovery Tank w/Pump ................................................................ 8 - 9
Vacuum Components .................................................................................. 10 - 11
Brush Drive Assemblies .............................................................................. 12 - 13
Squeegee Assembly ................................................................................... 14 - 15
Wiring Diagram ........................................................................................... 16 - 17
1
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
Operators must read and understand this manual before operating or maintaining this
equipment.
• Do not operate this scrubber in the red discharge area of the battery condition meter.
Operating the scrubber for long periods in the red zone of the gauge will cause overheating
of the motors and possible permanent damage to the batteries may result. If you are using
the machine and thebattery indicator needle does go into the red, finish the area you are
working in and then recharge the batteries immediately.
• Keep hands and feet clear of moving parts while machine is in operation.
• All switches must be in the “OFF” position when charging batteries.
• Electrical motors and components can cause an explosion when operated near explosive
materials or vapors. Do not operate this machine nearflammable materials such as solvents,
thinners, fuels, grain dusts, etc.
• Make sure all switches are turned “OFF” and battery connections are removed before
performing any maintenance procedures.
• Store or park this machine on a level surface only.
• These machines are designed for level floor operation only. DO NOT OPERATE on ramps or
inclines.
• Battery acid can cause burns. When working on or around batteries, wear protective clothing
and safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of
batteries.
• This machine is not suitable for picking up hazardous dust.
Charging batteries generates explosive gases. DO NOT CHARGE BATTERIES WHEN OPEN
FLAMES OR SPARKS ARE PRESENT. DO NOT SMOKE. Make sure the charger is turned off
before disconnecting it from the batteries. Charge the batteries in a well-ventilated area.
Maintenance and repairs must be performed by authorized personnel.
SAVE THESE INSTRUCTIONS
2
ELECTRICAL REQUIREMENTS:
This piece of equipment operates on 24 Volt DC.
BATTERY REQUIREMENTS:
2 x 12V 80 Amp Hour 20 Hour Rate Deepcycle P/N 956721
2 x 12V 105 Amp Hour 20 Hour Rate Deepcycle P/N 956712
BATTERY SERVICE AND INSTALLATION:
*Warning: Battery acid can cause burns. When working on or around batteries, wear protective
clothing and safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of
batteries.
BATTERY INSTALLATION:
1. Disconnect tank drain hose from rear of machine.
2. Disconnect vacuum recovery hose.
3. Raise tank assembly by gripping side hand holds, and tilting forward.
4. Position tank kickstand as shown below, figure 1, to hold tank in upright position. To lower,
raise tank slightly forward and manually move kickstand to freed position.
5. Install batteries as shown in figure 2.
CHARGING OF BATTERIES:
Charging of batteries generates explosive gases. DO NOT CHARGE BATTERIES WHEN
OPEN FLAMES OR SPARKS ARE PRESENT. DO NOT SMOKE. Make sure the charger is
turned off before disconnecting it from the batteries. Charge the batteries in a well-ventilated
area. Fluid levels should be checked before and after charging and maintained at the proper
levels.
Figure1 Figure 2
3
1. Squeegee left lever 8. Vacuum recovery hose
2. Vacuum switch 9. Power assist control
3. Battery condition gauge 10. Foot pedal for lower/raising brush
4. Brush switch 11. Pump switch
5. Solution control lever 12. Auxiliary out
7. Drain hose for recovery tank
CONTROLS
4
BRUSH REMOVAL
Empty solution and recovery tanks.
Disconnect batteries.
Remove Squeegee assembly.
Lower brush.
Tilt machine as shown (figure 3) until machine rests on foot pedal.
Brush has a snap-on push off clutch plate. Pushing brush away from the machine from the
side, will release brush assembly.
To install: Hold brush in the center and snap on to drive hub.
Figure 3
5
OPERATING INSTRUCTIONS
1. Filling: Fill the solution tank with the desired amount of water and add liquid cleaning solution
to the proper dilution ratio. DO NOT USE powdered cleaning chemicals. Powders are unlikely
to dissolve thoroughly, resulting in clogging the in-line solution filter. This can reduce or stop
water flow to the brush.
2. Close lid.
3. Lower brush assembly.
- To lower the brush, first push the pedal slightly towards the center of the
machine (unlock it), then release it slowly.
- To lift the brush, press the pedal down until lift mechanism engages.
4. Turn on brush switch.
5. Adjust solution control feed lever.
6. Turn on vacuum switch.
7. Lower Squeegee assembly.
After Use:
1. Turn off solution feed.
2. Switch off brush and raise.
3. Raise Squeegee assembly.
4. Turn off vacuum motor.
Solution and recovery tanks should be emptied after every use.
MAINTENANCE:
Daily 1. Clean float assembly & Squeegee blades. Vac filter.
2. Recharge batteries (check battery acid levels before and after
charging).
Monthly 1. Check wear on Squeegee blades.
2. Grease rear wheels.
3. Grease pivot points on brush motor assembly.
Every 500 hours check condition of carbon brushes on vacuum motor and brush
drive motor.
6
Main Components
7
Parts List
Item Part No. Qty. Description
1 430000MCH 1 Base Assy. 17 B/E Machined
2 430001MCH 1 170 Sol/Recovery Tank Assy.
3 430002 1 Cover Poly 170 Burgundy
4 430044 2 Hinge Lid 17 B/E
5 430046 2 Side Skirt Retainer 17
6 430049 1 Splash Skirt 17 B/E
7 430126 2 Hinge Backing Plate
8 430136 1 Gasket Seal Kit (4)
9 430141 1 Splash Skirt 170
10 430142 1 Mounting Bracket
11 450021 1 Hinge
12 711104 3 SCR-ST-A #10 x .50
13 711161 18 SCR-HI/LO #10 x 3/4 PL
14 712536 6 SCR-MC 10-24 x .50 SS
15 712560 6 SCR-MC 1/4 - 20 x .50 S.S.
16 712822 6 SCR-THMS 10 - 24 x .50 STPL
Table des matières
Autres manuels Minuteman Scrubber
Minuteman
Minuteman Port A Scrub 12 Battery Guide de configuration
Minuteman
Minuteman ES2832 Manuel utilisateur
Minuteman
Minuteman E17 Manuel utilisateur
Minuteman
Minuteman E24 Manuel utilisateur
Minuteman
Minuteman 380 Mode d’emploi
Minuteman
Minuteman RoboScrub 20 Manuel utilisateur
Minuteman
Minuteman m12110 Manuel utilisateur
Minuteman
Minuteman 260 Series Mode d’emploi
Minuteman
Minuteman SCV 28/32 Mode d’emploi
Minuteman
Minuteman E17 Manuel utilisateur
Minuteman
Minuteman SCV28 Mode d’emploi
Minuteman
Minuteman ES260 Mode d’emploi
Minuteman
Minuteman E320QP Guide de démarrage rapide
Minuteman
Minuteman E28 Manuel utilisateur
Minuteman
Minuteman 200X Mode d’emploi
Minuteman
Minuteman E20 SPORT Manuel utilisateur
Minuteman
Minuteman 260 Series Mode d’emploi
Minuteman
Minuteman E26ECO Manuel utilisateur
Minuteman
Minuteman M14100 Mode d’emploi
Minuteman
Minuteman E14 Manuel utilisateur
