MINOURA 971-3 Manuel utilisateur

Bicycle Display Stand 971-3 instructions manual

(ver.2.4 2019/4)

Thank you for choosing Minoura 971-3.

Read this instructions carefully to understand well how this stand is constructed before starting assembling.

- 1 -

800mm

520mm

270mm

920mm

850mm

Completed image and dimensions of 971-3

(in the settings the bikes facing rightward)

IMPORTANT NOTES

• For standard 2-wheel bike only. No recumbent, tandem and any other type of bikes.

• For 24-inch wheel or larger only. Any bike with smaller wheel such as BMX or juvenile bike, and a special bike

with too low bottom bracket height or carbon monocoque frame may not t to this stand.

• In the case of electric bike, the weight is limited under 30 kgs each.

• The bike is supported at just 3 points; front tire, rear tire and the bottom bracket. Adjust the BB Support height

precisely in each case to expect maximum stability.

• The bike direction is xed as per the Stair Frame direction. Wrong direction cannot mount the bike properly.

• Do not step on this stand. The stand body is not so durable to support your weight.

• Setup this stand on horizontal and level oor, especially when installing the optional Caster Kit.

• When moving this stand, get off all bikes from the stand before action.

• Check regularly if each bolt and nut are rmly tightened.

Contact MINOURA JAPAN

134-1 Shimomiya, Godo, Anpachi, Gifu 503-2312 Japan

Fax: +81-584-27-7505

Mail: [email protected]

Web: www.minoura.jp

Made in Japan

To avpoid stain to the oor or carpet, put the supplied

round transparent lm on each back of Foot Adjuster.

- 2 -

How To Assemble 971-3

Required Tools: 1 x Phillips Screwdriver (#2), 2 x 13mm Socsket Wrench

First of all, check all small parts are correctly prepared.

Parts List

2 x Base Frame 4 x Round Head Screw M5x40

3 x Stair Frame 3 x Hex Head Bolt M8x30

2 x Pillar-S (223mm) 6 x Hex Head Bolt M8x35

2 x Pillar-M (473mm) 8 x Hex Head Bolt M8x45

2 x Joint Frame 2 x Hex Head Bolt M8x60

3 x B.B. Support 15 x Metal Collar (short)

6 x Tire Cradle 6 x Metal Collar (long)

4 x Foot Adjuster 4 x M5 Spring Washer

21 x M8 Spring Washer

21 x M8 Flat Washer

8 x M8 Nut

Assemble 2 sets of the Side Frame.

Connect the Pillar S (223mm) and the Pillar-M (473mm)

with the Joint Frame. Tighten the screw to fix.

Pillar-M

(473mm)

Joint Frame

Pillar-S

(223mm)

M5x40 Screw

M5 Spring Washer

Make sure the direction of Pillar-M.

Joint Frame must be parallel when

standing both pillars.

Assemble the Base Frame with each Side Frame.

Install the Foot Adjusters on both ends of the Base Frame.

Base Frame

Foot Adjuster

Collar (long)

M8 Flat Washer

M8 Spring Washer

Hex Bolt M8x45

Connect both Side Frames with three (3) Stair Frames.

On the 1st level Stair Frame, you use longer M8x60 bolt.

Hex Bolt M8x60

M8 Spring Washer

M8 Flat Washer

Collar (short)

Stair Frame

Collar (long)

M8 Flat Washer

M8 Spring Washer

M8 Nut

Make sure there are two (2) holes on each Stair

Frame for mounting the Bottom Bracket Support.

To set the bike heading right, place the Stair

Frame to have the holes in left side.

Install the Stair Frames on the 2nd and 3rd levels.

Set all frames in the same direction if you wish to set the

bikes in same direction.

Hex Bolt M8x45

M8 Spring Washer

M8 Flat Washer

Collar (short) Stair Frame

｝

Long

Short

Bike Direction

- 3 -

Install a pair of Tire Cradles on each Stair Frame.

Each Tire Cradle is position adjustable in 5 points in order to fit

various sizes of bike wheelbase.

To expect maximum stability of bikes, choose the best position

each by each.

Tire Cradle

Hex Bolt M8x35

Collar (short)

M8 Flat Washer

M8 Spring Washer

M8 Nut

When mounting short wheelbase

bike, turn Tire Cradle that the

bolt head comes through the

larger hole.

Install the Bottom Bracket Support to the Stair Frame.

Be sure there are two (2) holes on the Stair Frame.

The center hole is for short wheelbase bike. The further hole is for standard bike.

Put the triangle bracket between the chain-stays and support the down-tube with

the U-shaped bracket.

If you mount the bike in wrong direction

against you set on the Stair Frame, the

wheels will have to come off from the Tire

Cradles.

Make sure the bike direction follows the

stand direction.

B.B. Support

For standard wheelbase bike

For short wheelbase bike

Collar (short)

M8 Flat Washer

M8 Spring Washer

Hex Bolt M8x30

- 4 -

How To Mount Bike on 971-3

Place the bike on the floor in the same direction you set on the Stair Frame.

Place both front and rear tire on the Tire Cradles.

While supporting the bike with hand, loosen the knob bolt on the B.B. Support, and extend the upper support until it

touches the bottom bracket.

After confirming the bike is stably supported that the U-shaped part holds the down-tube and the triange guide is put

between the chain-stays, tighten the knob bolt to hold the position.

5In the end, shake the bike side to side to confirm the bike is stably supported, then leave from the stand.

Optional Items

By replacing the Foot Adjuster to a caster wheel, you can

move 971-3 to anywhere while mounting bikes on it.

Caster Kit contains a reinforcement bar and beam rods to

keep the frame solid and stable.

The reinforcement bar will be installed under Pillar-M

(473mm).

Caster Wheel

Model Variation

By combining 971-3 and 971-3H,

you can use them as a one unit

for totally 6 bikes.

If you cannot hold the bike on 971-3 stable due to the

special frame shape such as carbon monocoque or a

battery for electric shifting device sits near the bottom

bracket, you need to add this wheel holder between the tire

cradle and the frame instead of using the B.B. Support.

This cradle holds the whole rear wheel.

Caster Kit Rear Wheel Support

971-4 971-3H

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels MINOURA Support et étagère

MINOURA

MINOURA SS-700 Manuel utilisateur

MINOURA

MINOURA RS-4000 Manuel utilisateur

MINOURA

MINOURA DW-2 Manuel utilisateur

MINOURA

MINOURA T-817 Manuel utilisateur

MINOURA

MINOURA DS-110 DS-100H Manuel utilisateur

MINOURA

MINOURA DS-2200 Manuel utilisateur

MINOURA

MINOURA VERGO Manuel utilisateur

MINOURA

MINOURA VERGO EXCEL-S Manuel utilisateur

MINOURA

MINOURA VERGO EXCEL Manuel utilisateur

MINOURA

MINOURA RS-5000 Manuel utilisateur

MINOURA

MINOURA LEVEL-170 Manuel utilisateur

MINOURA

MINOURA P-500AL-2 Manuel utilisateur

MINOURA

MINOURA P-500AL-6S Manuel utilisateur

MINOURA

MINOURA P-600AL Manuel utilisateur

MINOURA

MINOURA RS-1100 Manuel utilisateur

MINOURA

MINOURA PAIR STAND Manuel utilisateur

MINOURA

MINOURA P-700X Manuel utilisateur

MINOURA

MINOURA DSX-2M Manuel utilisateur

MINOURA

MINOURA BIKE PIT Manuel utilisateur

MINOURA

MINOURA W-400 GAZZY Manuel utilisateur

MINOURA

MINOURA FCG-310 - MANUAL 2 Manuel utilisateur

MINOURA

MINOURA LEVEL-170H Manuel utilisateur

MINOURA

MINOURA DS-520 - ASSEMBLY Manuel utilisateur

MINOURA

MINOURA P-700X Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur