MinimumRC Flycat Manuel utilisateur

Flycat

Assembly Instructions

Important notification

1.The model is supplied with UFO and 502 glue. UFO is for bonding foam parts, and 502 for

bonding wood, carbon fiber and metal parts. 502 glue will cause serious corrosion to foam parts.

2.Please wait for the glue to dry and solidify in each installation step before the next ins tallation.

3.Please avoid using flame to heat the heat shrinkable tube on the model. Electric iron shall be

used for heating.

4.Please use razor blade to remove the parts from the plate. Do not tear the parts by force.

Assemble the wheels. Thread the wood wheel core on the landing gear steel wire, apply glue on

its outer edge, and then put it into the tire.

As shown in the figure, bend the center part of the front landing gear backward to realize the shock

absorption function.

Thread the wheels into the landing gear steel wire, and bend the outer end of the steel wire with

pointed nose pliers. Or: put 2mm heat shrinkable pipe into the outer end of steel wire, and fix the

pipe with glue to hold the wheels.

Bend the top fixed seat of nose landing gear 90 degrees to the right.

Connect the servos to a powered receiver. Bind the receiver with your transmitter to make the

servos return to their neutral point. Test whether the servos are normal, and install the servo arms

according to the position shown in the picture. (use screws to fix the servos on the servo base

from below.)

Note: Important step. Please make sure that the servos have been tested and installed in strict

accordance with the following picture. After assembling the model, it will be not able to adjust.

Combination of side plate and servo base.

Pay attention to keep both sides symmetrical without distortion. Please wait until the glue is

completely cured before the next installation step.

Install the cabin top plate.

Note: as shown in the detail drawing, the top plate slightly protrudes from the edge of both sides

of the plate (0.1-0.2mm), which will help to keep the sticker flat in the later stage . Note: apply the

glue to the inner wall of the two sides of the plate.

Please wait until the glue is completely cured before the next installation step.

Use the end of a carbon fiber rod to score through the half-cut line of the wing surface. After

scored through the half-cut line, ailerons can move in both directions.

The wing can be bent down along the center longitudinal scribe.

Install the wings symmetrically.

Note: before applying glue, please test fit the wing to ensure it can be installed in place.

Assemble the tail & EDF system.

Note: EDF motor needs to be fixed with a small amount of 502 glue.

Use the end of a carbon fiber rod to score through the half-cut line of the elevator surface.

Paste the sticker on the top of the fuselage to form a hinge connection for the hatch cover to be

turned over. Glue can be used at the hinge joint to increase strength.

Aileron flexible transmission system: slightly bend the steel wire to reduce the moving resistance.

Ce manuel convient aux modèles suivants

1

Autres manuels MinimumRC Jouet

MinimumRC

MinimumRC J-3 Manuel utilisateur

MinimumRC

MinimumRC Messerschmitt BF-109 Manuel utilisateur

MinimumRC

MinimumRC F8F-RareBear Pro Manuel utilisateur

MinimumRC

MinimumRC Spitfire Manuel utilisateur

MinimumRC

MinimumRC Tigermoth Manuel utilisateur

MinimumRC

MinimumRC P-51 Mustang Manuel utilisateur

MinimumRC

MinimumRC A6M5-D Manuel utilisateur

MinimumRC

MinimumRC F8F-RareBear Pro Manuel utilisateur

MinimumRC

MinimumRC P-51 Mustang Manuel utilisateur

MinimumRC

MinimumRC Butterfly V1 Manuel utilisateur

MinimumRC

MinimumRC Cessna-152 Manuel utilisateur

MinimumRC

MinimumRC T-34 Mentor Manuel utilisateur

MinimumRC

MinimumRC T-34 Mentor Manuel utilisateur

MinimumRC

MinimumRC Piper Cub J-3 Manuel utilisateur

MinimumRC

MinimumRC Spacewalker V2 Manuel utilisateur

MinimumRC

MinimumRC T-28 Trojan Manuel utilisateur

MinimumRC

MinimumRC F8F Rare Bear Manuel

MinimumRC

MinimumRC Cessna L-19 Manuel utilisateur

MinimumRC

MinimumRC A6M5-Q Series Manuel utilisateur

MinimumRC

MinimumRC Shrimp V2 Manuel utilisateur

MinimumRC

MinimumRC Minimoa Manuel utilisateur

MinimumRC

MinimumRC ASG-32 Manuel utilisateur

MinimumRC

MinimumRC Ju-87 Manuel utilisateur

MinimumRC

MinimumRC Beech V-35 Manuel

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur