Minelab F3 Manuel utilisateur

OPERATIONS MANUAL

F3 COMPACT Ve r s i o n 2

Metal Detector

Part No: 4901-0174 Revision 2

WARNING

THIS DOCUMENT CONTAINS INTELLECTUAL PROPERTY,

TECHNICALAND PROPRIETARY DATAAND INFORMATION

AND OTHER MATERIAL OWNED SOLELY BY MINELAB

ELECTRONICS PTY LIMITED. THIS MATERIAL MUST NOT BE

USED WITHOUT THE PRIOR WRITTEN PERMISSION OF

MINELAB ELECTRONICS PTY LTD.

This document is protected by copyright. Apart from any use permitted

under the Australian Copyright Act 1968 (Cth) or other applicable laws,

any unauthorised use, appropriation or reproduction of this document or

any part of it is strictly prohibited. No part of this document may be used

or reproduced by any means or by any process, in any form, without the

prior written permission of the copyright owner Minelab Electronics Pty

Ltd of 2Second Avenue, Mawson Lakes, SA 5095, Australia.

F3 COMPACT Version 2 Operations Manual

Table of Contents

1. Introduction.............................................................................................. 3

2. General Description and Preparation....................................................5

2.1 Mine Detecting Set................................................................................ 5

2.2 F3 COMPACT Main Components .........................................................6

2.3 F3 COMPACT Preparation....................................................................8

3. Functional Description..........................................................................12

3.1Functional Controls and Displays........................................................12

3.1.1 On/Off Switch............................................................................12

3.1.2 Sensitivity Knob.........................................................................13

3.1.3 Ground Balance/Audio Reset Button........................................14

3.1.4 Noise Cancel Button .................................................................14

3.1.5 Volume Control .........................................................................15

3.1.6 LED Display ..............................................................................15

3.1.7 Battery Status ...........................................................................17

3.1.8 Earset Socket............................................................................17

3.2 Functional Tones.................................................................................18

3.3 Test Piece –Functional Test ...............................................................19

4. Operating Procedures...........................................................................21

4.1 Introduction..........................................................................................21

4.2 Standard Procedure ............................................................................22

4.2.1 STEP 1 Switch ON....................................................................22

4.2.2 STEP 2 Ground Balance ..........................................................23

4.2.3 STEP 3 Test Piece....................................................................24

4.3 Optional Procedure .............................................................................26

4.3.1 Noise Cancel.............................................................................26

4.3.2 Audio Reset...............................................................................27

4.4 Sweeping Procedure...........................................................................29

F3 COMPACT Version 2 Operations Manual

4.5 Pinpointing Procedure.........................................................................30

4.5.1 STEP 1 Mapping the Target.....................................................30

4.5.2 STEP 2 Determine Centre of Target.........................................32

4.6 Multiple Targets...................................................................................33

4.6.1 STEP 1 Mapping the Target.....................................................33

4.6.2 STEP 2 Determining the Centre of Target...............................34

4.7 Operating Multiple Detectors in Close Proximity.................................34

4.8 Completion of Operations....................................................................36

5. Care and Troubleshooting....................................................................37

5.1 Routine Care.......................................................................................37

5.2 Troubleshooting...................................................................................38

6. Specifications ........................................................................................39

F3 COMPACT Version 2 Operations Manual

1. Introduction

Since 1996, Minelab has designed, developed and manufactured

its range of detectors to meet the requirements of mine and

unexploded ordnance clearance operations throughout the

world. Through its patented and unique technology, Minelab has

emphasised equipment capability and operator safety in its

products.

The F3 COMPACT is a lightweight, compact detector that

includes a uniquely designed mechanical platform thereby

providing superior ergonomics.

The F3 COMPACT incorporates patented bipolar technology that

enhances Minelab’s renowned and highly successful Multi-Period

Sensing (MPS) technology. Through MPS, the sensitivity of a

detector remains consistent regardless of the mineralised content

of soil. Bipolar technology also helps to eliminate the possibility of

initiating a magnetic influence mine. Combined with ‘static

coupling’ the F3 COMPACT does not require motion to detect a

target thereby making pinpointing techniques fast and accurate.

Figure 1: F3 COMPACT mine detector

F3 COMPACT Version 2 Operations Manual

The F3 COMPACT is a robust detector that is extremely simple

to operate. When working in an environment that includes highly

mineralised ground or electrical interference from overhead

power lines or other sources, simple and quick semi-automatic

procedures can be initiated by an operator resulting in the

detector continuing to perform at maximum capability.

The F3 COMPACT incorporates several safety features such as

Low Battery and System Fault warnings, audible confirmation at

the completion of specific operational procedures, and

continuous microprocessor controlled internal self-testing. The

inclusion of a Test Piece provides the operator with a quick and

easy check to ensure that the detector is working at its

operational capability.

The F3 COMPACT also provides a visual indication of detection

via a Light Emitting Diode (LED) display. Sensitivity settings can

be changed through seven preset selections. If required, the F3

COMPACT can be programmed to user initiated customised

volume and sensitivity selections using Minelab’s configuration

software.

Components of the F3 COMPACT are manufactured within tightly

controlled parameters so that they can be interchanged in the

field without any requirement for calibration.

The F3 COMPACT is designed to satisfy MIL STD 810G.

NOTE

Although the F3 COMPACT can withstand immersion to a depth of

three metres for short periods of time, it is NOT designed for use as

an underwater detector.

F3 COMPACT Version 2 Operations Manual

2. General Description and Preparation

2.1 Mine Detecting Set

The F3 COMPACT is supplied as a mine detecting set (Figure 2)

comprising:

Hard Case (optional)

Operations Manual

Detector

Field Guide

Soft Carry Bag

Test Piece

Earset (Speaker On and

Speaker Off variants)

Four C-Cell Batteries

(Alkaline or Rechargeable)

The optional Hard Case permits the stowage of the detector

inside the Soft Carry Bag and provides protection for the

detector when in transit or placed in storage.

The Soft Carry Bag allows the operator to comfortably carry the

detector when use of the Hard Case is impractical. The Soft

Carry Bag is not suitable for use when transporting the detector

by road or air. For added protection during road or air transport, it

is recommended that the detector be packed in the Hard Case.

Figure 2:F3 COMPACT mine detecting set

F3 COMPACT Version 2 Operations Manual

2.2 F3 COMPACT Main Components

Figure 3 identifies the main components of the F3 COMPACT.

Battery Compartment –contains 4 x C cell alkaline or

rechargeable batteries. A battery map is provided to indicate correct

alignment of batteries.

Armrest and Strap –provided for operator comfort when the F3

COMPACT is used for prolonged periods. The Armrest can be

extended for operator comfort.

Figure 3: F3 COMPACT main components

Armrest Strap

Controls

Upper Shaft

Upper Camlock

Middle Shaft

Lower Camlock

Coil

Lower Shaft

Coil Pivot Assembly

Skid Plate

Test Piece

Battery

Compartment

Earset

Connector

Main Body

Armrest

F3 COMPACT Version 2 Operations Manual

Test Piece –conveniently stowed on the Armrest to allow the

operator to ensure the detector is working at its operational

capability.

Earset Connector –provides connection for the Earset and also

the programming cable when using the configuration software to

customise volume and sensitivity settings.

Main Body –waterproof housing containing the detector electronics

and batteries.

Handle Assembly –collapsible handle that also contains Ground

Balance/Audio Reset button, LED display, LED On/Off button, Noise

Cancel button, Volume Increase/Decrease and Battery Low LED

indicator.

Controls –On/Off and Sensitivity selection knobs –both controls

have a lift to turn safety feature to prevent accidental adjustment.

Shaft Hinge –pivot point for unfolding or folding the shafts. The

hinge is only locked in position when the Handle Assembly is in its

deployed position.

Upper, Middle, Lower Shafts –carbon fibre shafts that are

adjustable for operator comfort and for changes in demining

positions.

Upper and Lower Camlocks –self-cleaning locking mechanisms to

secure middle and lower shafts.

Coil Pivot Assembly –permits the tilt and rotation of the coil and

provides a tension screw for adjustment as required.

Coil –waterproof enclosed coil to eliminate possible interference

from vegetation. The coil’s mono loop design ensures consistent

sensitivity around the entire circumference, and across the complete

surface of the coil.

Skid Plate –removable cover that protects and prolongs the life of

the coil thereby reducing maintenance costs.

F3 COMPACT Version 2 Operations Manual

2.3 F3 COMPACT Preparation

To prepare the detector for use, conduct the following procedure:

a. Open the Hard Case and/or Soft Carry Bag.

b. Remove the F3 COMPACT and inspect for obvious signs of

damage. If damage is evident, report to the supervisor/team

leader.

c. Unlock the Battery Compartment Lid by twisting the Battery

Lock Lever counter clockwise one-quarter turn. Once

unlocked, pull the lid away from the Battery Compartment (the

lid will stay attached by a tether as shown in Figure 4).

d. Using the battery map located on the side of the Main Body,

insert four C cell batteries. Close the Battery Lid and rotate the

Battery Lock Lever clockwise one-quarter turn. If the batteries

are inserted incorrectly, the F3 COMPACT will fail to function

when switched on.

e. Using Figure 5 as a guide, unfold and adjust the F3

COMPACT.

f. Extend the Lower and Middle Shafts to suit the selected

demining position as shown in Figure 6.

NOTE

The F3 COMPACT requires 4 C cell batteries for operation. Use only

high quality alkaline or rechargeable batteries. Minelab recommends

that only rechargeable batteries with a capacity of 4000 mAH or

greater be used with the F3 COMPACT. Rechargeable batteries

have specific charge/discharge maintenance requirements, which

should be strictly followed to ensure maximum battery life.

Figure 4: Opening the Battery Lid

Autres manuels pour F3

Table des matières

Autres manuels Minelab Détecteur de métaux

Minelab

Minelab VANQUISH 540 Guide de démarrage rapide

Minelab

Minelab GPX 6000 Manuel utilisateur

Minelab

Minelab F1A4 Manuel utilisateur

Minelab

Minelab F3 Manuel utilisateur

Minelab

Minelab PRO-FIND 25 Manuel

Minelab

Minelab EQUINOX 600 Manuel utilisateur

Minelab

Minelab EQUINOX 600 Manuel utilisateur

Minelab

Minelab The Sovereign Manuel utilisateur

Minelab

Minelab VANQUISH 340 Manuel utilisateur

Minelab

Minelab Excalibur II Manuel utilisateur

Minelab

Minelab E-Trac Manuel utilisateur

Minelab

Minelab XT 17000 Manuel utilisateur

Minelab

Minelab F3 Mine Detector Manuel utilisateur

Minelab

Minelab Sovereign Elite Manuel utilisateur

Minelab

Minelab GPX-4000 Manuel utilisateur

Minelab

Minelab Manticore Manuel utilisateur

Minelab

Minelab X-Terra 30 Manuel utilisateur

Minelab

Minelab GPX-4500 Manuel utilisateur

Minelab

Minelab SDC 2300 Manuel utilisateur

Minelab

Minelab Musketeer ADVANTAGE Manuel utilisateur

Minelab

Minelab F3 COMPACT Metal Mine Manuel utilisateur

Minelab

Minelab EQUINOX 600 Manuel utilisateur

Minelab

Minelab VANQUISH 440 Manuel utilisateur

Minelab

Minelab SD2200V2 Manuel utilisateur

Manuels Détecteur de métaux populaires d'autres marques

Garrett

Garrett MAGNASCANNER CS 5000 Manuel utilisateur

Valex

Valex 1800200 Manuel utilisateur

Gauss

Gauss MIL MD Manuel utilisateur

Velleman

Velleman CS130 Manuel utilisateur

Sears

Sears 321.596370 Manuel utilisateur

Eriez

Eriez X8 Manuel utilisateur

Steinberg Systems

Steinberg Systems SBS-MD-22 Manuel utilisateur

Zircon

Zircon MetalliScanner m60c Manuel utilisateur

nalanda

nalanda MD027 Manuel utilisateur

REV Ritter

REV Ritter CB-7005 Manuel utilisateur

Fisher Research Labs

Fisher Research Labs F70 Manuel utilisateur

Steinberg Systems

Steinberg Systems SBS-MD-12 Manuel utilisateur

GOLDEN MASK

GOLDEN MASK 5 Manuel utilisateur

Grizzly

Grizzly YM 203 Manuel utilisateur

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Manuel utilisateur

Treasure Cove

Treasure Cove Vibra-Probe 560 Manuel utilisateur

Accurate Locators

Accurate Locators XL16 IMAGER Manuel utilisateur

Teknetics

Teknetics G2 Manuel utilisateur