Garrett MAGNASCANNER CS 5000 Manuel utilisateur

OWNER S MANUAL

MAGNASCANNER CS 5000 with DSP

MODEL 11674XX

Garrett Metal Detect rs, Inc.

1881 W. State Street

Garland, TX 75042-6797 USA

Tel: 972-494-6151

Fax: 972-494-1881

E-mail: [email protected] m

APPROVED

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Ca tion: Read This Before Operating.

For best possible operation, read this manual carefully.

An optional stabilizer base, Part Number 1603900, is a ailable and

may be used to anchor the detector. It is recommended that this base

be used in outdoor applications or where there is danger of the unit

being pushed o er. Be sure to follow installation directions carefully.

Electrical requirements:

Fully automatic 100 to 240 VAC, 50/60 Hertz, 5 Watts, no rewiring or

switching required.

Compliance with Regulatory Standards requires that a Cord Set be

used for proper installation. (See page 8.)

Always place the metal detector on a le el stable floor that is not sub-

ject to mo ement or ibration.

Do not dri e nails or drill holes into the side panels.

Position away from rain, mist and condensation.

Use caution when placing the metal detector next to telephone sys-

tems, tele ision monitors, electric motors, transformers, power

cables, or control circuits. Excessi e electrical noise will show acti ity

on the LED bar graphs.This situation should be a oided whene er

possible.

Security type metal detectors are important tools, designed for use

within a total security screening system. It is the responsibility of the

end user to define the system and to ensure proper operation of all

aspects of the system.

If you are not familiar with the Mag-

nascanner, it is recommended that you

view the Video that accompanied this

unit before beginning this checklist. To

prepare the Magnascanner for use...

Y U MUST:

❏1. Assemble unit and move to desired

location. Make necessary arrangements

of surrounding furniture and equipment.

(See Site Selection, Page 7.) Attac

cables necessary for remote consoles,

multiunit slaving, or control relays.

❏2. Connect unit to power source and

observe LCD panel. T e unit will begin

t e self test sequence automatically

w en power is connected. Correct any

problems reported. (See Self-Diagnostic

Tests, Page10.)

❏3. Determine optimum program based

on your particular application. (See Pro-

grams, Page 35.)

❏4. Set unit to desired program (See

Supervisor Adjustments, Program, Page

14.)

❏5. Determine sensitivity setting

required, using t e alarm level reading

and sample test objects selected for

your application. Be t oroug ; perform

t e test at various elevations and orien-

tations for objects t at produce t e ig -

est alarm level readings. (See Supervi-

sor Adjustments, Alarm Level Reading,

Page 15.)

❏6. Set sensitivity to value determined

in step 6.2 (See Supervisor Adjustments,

Sensitivity, Page14.)

❏7. Return to Operate Mode by pressing

PERATE touc pad.

❏8. Perform verifications test using

selected objects. (See Supervisor

Responsibilities, Page 16.)

STANDARD SETUP AND

PERATI N PR CEDURE

Y U MAY ALS :

❏9. If multiple unit operation is being uti-

lized, verify units are properly inter-

leaved. (See Multiple Unit Operation,

Page 38.)

❏10. If unit appears noisy, i.e. more t an

two LED s persistently displayed on bar

grap , furt er adjustments are required,

proceed to Step 11. If unit appears

quiet, proceed to Step 13.

❏11. Adjust video filter until noise sub-

sides. (See Installation Adjustments,

Video Filter, Page 13.)

❏12. Repeat steps 4-8.

❏13. Adjust tone to desired level. (See

Installation Adjustments, Tone, Page 12.)

❏14. Adjust volume to desired level. (see

Operating Instructions, Volume, Page 5.)

❏15. Alter access codes, if desired. (See

Installation Adjustments. Alter Access

Code #1 and #2, Page 13.)

SECURITY

When used in a security (weapons detection)

application, it is important that the following

procedures be followed:

1. Determine t e security level appropriate to t e

application.

2. Select test object(s) t at will allow calibration

and verification of t e desired settings.

3. Maintain t e Operation Work S eet s own on

Page 34 of t is booklet.

4. Using t e same test objects, verify t e calibra-

tion daily and any time t e equipment is moved

or t e operating environment c anges.

5. Seek corrective action immediately for any

problems or performance deficiencies and report

problems/deficiencies to t e sales representative

and manufacturer as well.

Magnascanner, Super Scanner and Enforcer G-2 are “ of Garrett Electronics, Inc.

If further assistance is required, call the factory at 1-800-234-6151.

TABLE OF CONTENTS

1. GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. CONTROLS & MODULES

2.1. DISPLAY PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2. TOUCHPADS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.3. INTERNAL MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3. INSTALLATION INSTRUCTIONS

3.1. SITE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2. ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4. SELF-DIAGNOSTIC TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

5. INSTALLATION ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6. SUPERVISOR ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

7. SUPERVISOR RESPONSIBILITIES . . . . . . . . . . . . . . . . . . . . . . . . . .16

. TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

9. MAINTENANCE & REPAIR

9.1. PERIODIC MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

9.2. REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

9.3. MODULE REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

9.4. REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

9.5. WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

10. OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

11. ADDITIONAL INFORMATION

11.1. OPERATIONS WORKSHEET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

11.2. PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

11.3. MULTIPLE UNIT OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

11.4. AC DC CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

11.5. REMOTE CONSOLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

11.6. BATTERY BACK-UP MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

11.7. STABILIZER BASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

11.8. ELECTRICAL WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Revised

1. GENERAL DESCRIPTION

The Garrett Magnascanner CS 5000 is a high-quality microprocessor-based walk-

through metal detector that provides superior metal discrimination and detection. It fea-

tures a DSP(Digital Signal Processor) that automatically suppresses or eliminates elec-

trical interference associated with x-ray devices, video monitors and communications

equipment, helping to reduce the likelihood of nuisance alarms and ultimately improving

traffic throughput. The Magnascanner CS 5000 offers a diverse range of programs to

meet your security needs. The detector is highly portable and can be operated by

remote console or a battery pack as needed.

A bright, highly visible LED (Light Emitting Diode) bar graph and lights indicating ready

and alarm conditions make it easy for the operator to interpret operating information.

Pacing lights located on side panels of the entrance side indicate whether or not a

patron may enter the walk-through. Pinpoint lights, located on the side panels of the

exit side, comprise 11 distinct pinpoint arrays that help the operator identify the precise

location of a metal object whether it is on the left, right or in the center of the body, or

from head to toe.

The LCD, located in the overhead panel and backlit for easy viewing, reports calibration

and operational information, including program and base sensitivity settings, operator

functions and fault indications. The LCD also provides information on instructions and

control functions, as well as a handy traffic count.

A convenient dual access code system protects calibration settings and eliminates the

need for keys to storage compartments. Calibration settings are further protected by a

non-resettable sequence code that enables the supervisor to monitor any changes

successful or otherwise that are made to the set up or program and base sensitivity.

In addition, a tamper alarm reports any unauthorized access attempts. An automatic

self test begins each time the OPERATE touchpad is pressed. In addition, fail safe,

self-testing circuitry provides information on operational interferences.

Other features of the Magnascanner MS 5000 include superior sensitivity, stability and

noise rejection. All of the electronics are built into the overhead panel, thereby eliminat-

ing the problems often associated with a cable-connected console.

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Revised

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Revised

2. CONTROLS & MODULES

2.1. DISPLAY PANEL

2.1.1. LED BAR GRAPH

This LED display at the top of the Control Panel indicates the detection intensity which

is based on the amount and composition of metallic objects passing through the unit.

2.1.2. READY LIGHT

This green light appears when full power has been turned on and the unit is ready to

operate. The light will also indicate when an individual inspection has been completed

by the unit and it is ready to accept the next person. Operators should make certain the

green light is visible before any individual is permitted to pass through the detector.

2.1.3. LCD PANEL

Large alpha/numeric LCD below the Bar Graph reports all operating, setup and diag-

nostic information of the unit. Because the unit is designed to be user-friendly, all reg-

ulation and control functions are self-prompting with necessary commands shown on

the LCD display.

2.1.4. ALARM LIGHT

This red light appears when the unit detects a targeted amount of metal on an individ-

ual, according to specifications of the Program and Sensitivity levels that have been

selected. Operators should be instructed to respond to all alarms. For any detector to

be effective in a security system it is absolutely necessary that the cause of EVERY

ALARM be determined.

2.2. TOUCHPADS

Eight touchpads on the overhead Control Panel perform all control functions:

2.2.1. STANDBY

When this touchpad is pressed, the unit goes into a low power mode, ready to be

returned to full operation when the OPERATE pad is touched. When STANDBY is dis-

played on the LCD, the green READY light is not visible and no processing can take

place in the unit. It is important to remember that the Power Switch located on the

Battery Back-up Module (See Page 42) should be set to its OFF position anytime the

system is being stored and anytime the system is not in use and is not connected to

AC power for more than 24 hours.

2.2.2. OPERATE

Whenever this touchpad is pressed, the Magnascanner CS 5000 activates all circuits,

initiates a self-diagnosis program and places the unit in the Operate Mode within fifteen

(15) seconds. This diagnostic program for instant fault detection can be activated at any

time by touching this OPERATE pad. If any faults are ever found, they will be immedi-

ately reported on the LCD display. (See Page 10.)

2.2.3. COUNTER

When this touchpad is pressed, the traffic count is displayed on the LCD display.

Pressing and holding this touchpad for ten (10) seconds causes the counter to return to

zero (0). Whenever the LCD is displaying information other than the current traffic

count, pressing this touchpad will cause the count to appear along with the Sequence

Number of changes that have been made to Program/Sensitivity settings. CT (Number)

and SEQ (Number) will appear. Each time the Program/Sensitivity Mode is accessed,

the Sequence Code that appears on the LCD will be advanced one number. It is rec-

ommended that a written notation be made on the Operations Worksheet (see

Page 34) whenever this code is accessed, explaining reasons for the access. If the

ACCESS touchpad has been pressed and an improper access code has been entered,

a * will appear before the sequence number (SEQ *37). This indicates that an unsuc-

cessful (unauthorized) attempt has been made to gain access to the

Program/Sensitivity setting.

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Revised

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Revised

2.2.4. VOLUME

When this touchpad is pressed, the volume level of the unit s audible alarm will be

shown on the LCD display and the actual volume of the alarm will be heard. The +and

-touchpads can be used by operators to raise or lower the volume. They should then

press OPERATE to return to the operate mode.

2.2.5. + AND -

These touchpads will be used to increase or decrease various numerical settings and

for certain On/Off functions.

2.2.6. PROGRAM

When this touchpad is pressed, the settings for Program and Sensitivity will appear on

the LCD display.

2.2.7. ACCESS

The ACCESS touchpad will be used only by supervisory management personnel. It

permits changing the Program and Sensitivity codes and also is used to control such

functions as synchronization of multiple units, pulse frequency, tone, etc. (See Page

12). The unit further protects security of control settings by maintaining a non-resettable

sequence code that indicates any attempt at seeking access to the settings. When this

touchpad is pressed, audio of the system will chirp and ENTER CODE will be dis-

played on the LCD, prompting the operator to enter an access code. If no attempt is

made to enter a code, the unit will continue chirping for ten (10) seconds and return to

Operate Mode. If the operator enters an incorrect code, audio will sound a Tamper

Alarm and ACCESS DEN ED will appear on the LCD for five (5) seconds. An asterisk

(*) will appear on the Sequence Counter indicating that an unsuccessful attempt has

been made to access the Installation or Program/Sensitivity Modes of the unit.

Operators should never touch this control.

If an operator should inadvertently press the ACCESS touchpad, no further action

should be taken and the unit will return automatically to the Operate Mode in about ten

(10) seconds.

Special Note

The above touchpad functions will be available to operators of the detector at all times.

Additional functions such as program and sensitivity settings and other adjustments neces-

sary only at installation time may be selected by pressing the ACCESS touchpad and enter-

ing a security code.

2.3. INTERNAL MODULES

2.3.1. CONTROLLER MODULE

This module (in the center) contains all circuit boards necessary for operation of the

detector. Two cables (A and B) that connect this module to the side panels are to be

plugged into the connectors at the top of each panel. The cover of the Controller

Module never needs to be removed except for:

lConnecting wires to remote alarm relays or synchronization circuitry (See Pages

38-40);

lConnecting a remote console (See Page 41);

lAttaching the optional battery back up (See Page 42);

lResetting to factory default Access Code (See Page 14).

Shown above is a view of the detection unit after the access door has been opened.

Three metal covers protect (from left) the POWER SUPPLY Module, CONTROLLER

Module and the BATTERY PACK Module (Optional).

2.3.2. POWER SUPPLY MODULE

This module contains all circuitry that relates to the power required for operation of the

detector. The Power Cord should be plugged into the Power Supply Module at the con-

nector on the lower left side.

2.3.3. BATTERY PACK MODULE (OPTIONAL)

This module, which includes two (2) 12v batteries and charging circuitry that comprise

the optional battery pack, will be stored behind this cover and connected with the

Controller Module. This pack has a switch which is used to disconnect battery power.

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Revised

MAGNASCANNER CS 5000

OWNER S MANUAL

' 2000 GARRETT METAL DETECTORS, INC.

4/30/00

PN 11674XX

Revised

This switch need be placed in the OFF position only during storage or when the unit is

not being used and is not connected to AC power for more than 24 hours. See Page 42

for installation instructions.

3. INSTALLATION INSTRUCTIONS

3.1. SITE SELECTION

The Garrett Magnascanner CS 5000 should be located on a level, stable floor with no

large metal items within three (3) feet. Any nearby large metallic object can interfere

with operation of the detector. Moving metallic objects, such as an escalator or revolv-

ing door, close to the detector can cause false alarms. Such alarms can also be caused

by electrical interference from radio telephones, television monitors, powerful electronic

motors and transformers, power cables and control circuits.

Garrett s special built-in circuitry is designed to suppress much of this electronic noise,

especially X-ray monitor horizontal synchronization signals and closed circuit television.

Multiple frequencies permit several Magnascanner units to operate simultaneously, in

close proximity.

For information concerning the operation of multiple units, see Page 38.

The site for a Magnascanner CS 5000 should be selected with requirements for its

pedestrian traffic and use in mind; i.e. space for waiting lines, operators and areas for

hand-scanning. Although the detector is effective with traffic moving in either direction,

best results are obtained when traffic enters from the side opposite to the control touch-

pads and LCD display.

Locate the archway where it will not be subject to rain, mist or condensation. Protect

the power cable from pedestrian as well as vehicular traffic.

Autres manuels pour MAGNASCANNER CS 5000

Ce manuel convient aux modèles suivants

Autres manuels Garrett Détecteur de métaux

Garrett

Garrett GTI 2500 Manuel utilisateur

Garrett

Garrett GTI 2500 Manuel utilisateur

Garrett

Garrett CSI PRO Manuel utilisateur

Garrett

Garrett TREASURE ACE 300 Manuel utilisateur

Garrett

Garrett Master Hunter CX Plus Manuel utilisateur

Garrett

Garrett MAGNASCANNER CS 5000 Manuel utilisateur

Garrett

Garrett Treasure Hound CX Manuel utilisateur

Garrett

Garrett Pro-Pointer Manuel utilisateur

Garrett

Garrett Z-Lynk Wireless System Manuel utilisateur

Garrett

Garrett SuperWAND Manuel utilisateur

Garrett

Garrett Sea Hunter Mark II None Manuel utilisateur

Garrett

Garrett EURO ACE Manuel utilisateur

Garrett

Garrett MAGNASCANNER PD 6500 Manuel utilisateur

Garrett

Garrett AT Pro Manuel utilisateur

Garrett

Garrett ATX Manuel utilisateur

Garrett

Garrett GTI 2500 Manuel utilisateur

Garrett

Garrett ACE 350 Manuel utilisateur

Garrett

Garrett Investigator G-500 Manuel utilisateur

Garrett

Garrett MULTI-FLEX ACE APEX Manuel utilisateur

Garrett

Garrett ACE 150 Manuel utilisateur

Garrett

Garrett AT Pro INTERNATIONAL Manuel utilisateur

Garrett

Garrett AT Gold Manuel utilisateur

Garrett

Garrett Metal Detector GTI 1500 Manuel utilisateur

Garrett

Garrett THD Manuel utilisateur

Manuels Détecteur de métaux populaires d'autres marques

Valex

Valex 1800200 Manuel utilisateur

Gauss

Gauss MIL MD Manuel utilisateur

Velleman

Velleman CS130 Manuel utilisateur

Sears

Sears 321.596370 Manuel utilisateur

Eriez

Eriez X8 Manuel utilisateur

Steinberg Systems

Steinberg Systems SBS-MD-22 Manuel utilisateur

Zircon

Zircon MetalliScanner m60c Manuel utilisateur

nalanda

nalanda MD027 Manuel utilisateur

REV Ritter

REV Ritter CB-7005 Manuel utilisateur

Minelab

Minelab F1A4 Manuel utilisateur

Fisher Research Labs

Fisher Research Labs F70 Manuel utilisateur

Steinberg Systems

Steinberg Systems SBS-MD-12 Manuel utilisateur

GOLDEN MASK

GOLDEN MASK 5 Manuel utilisateur

Grizzly

Grizzly YM 203 Manuel utilisateur

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Manuel utilisateur

Treasure Cove

Treasure Cove Vibra-Probe 560 Manuel utilisateur

Accurate Locators

Accurate Locators XL16 IMAGER Manuel utilisateur

Teknetics

Teknetics G2 Manuel utilisateur