Minebea Intec Puro YP-DP1 Manuel utilisateur
Puro® Thermal Direct Printer YP-DP1
Operating Instructions
98627-000-25 Edition 1.0.1 8/3/2020
Minebea Intec Bovenden GmbH & Co. KG, Leinetal 2, 37120 Bovenden, Germany
Phone: +49.551.309.83.0 Fax: +49.551.309.83.190
Foreword
Must be followed!
Any information in this document is subject to change without notice and does not represent a commitment on
the part of Minebea Intec unless legally prescribed. This product should only be operated/installed by trained
and qualied personnel. In correspondence concerning this product, the type, name, and release number/serial
number as well as all license numbers relating to the product have to be cited.
Note
This document is partially protected by copyright. It may not be changed or copied, and it may not be used
without purchasing or written permission from the copyright owner (Minebea Intec). The use of this product
constitutes acceptance by you of the abovementioned provisions.
Table of contents
1 Introduction.........................................................................................................................................2
1.1 Read the manual.........................................................................................................................................................2
1.2 This is what operating instructions look like..........................................................................................................2
1.3 This is what lists look like...........................................................................................................................................2
1.4 This is what menu items and softkeys look like.....................................................................................................2
1.5 This is what the safety instructions look like.......................................................................................................... 2
2 Safety instructions...............................................................................................................................4
2.1 General information...................................................................................................................................................4
2.2 Incoming goods inspection.......................................................................................................................................4
2.3 Before operational startup........................................................................................................................................4
3 Device description ...............................................................................................................................5
3.1 Overview......................................................................................................................................................................5
3.2 Dimensions..................................................................................................................................................................6
3.2.1 Paper format.....................................................................................................................................................6
4 Device installation................................................................................................................................ 7
4.1 Electrical supply.......................................................................................................................................................... 7
4.2 Data interface..............................................................................................................................................................7
4.3 Suspend printer ..........................................................................................................................................................8
5 Operating ............................................................................................................................................9
5.1 Connecting and switching on the device................................................................................................................9
5.2 Self-test........................................................................................................................................................................9
5.3 Menu.............................................................................................................................................................................9
5.4 Changing the paper roll.............................................................................................................................................9
6 Waste disposal policy..........................................................................................................................11
7 Specication.......................................................................................................................................12
7.1 Equipment supplied..................................................................................................................................................12
7.2 Technical data ............................................................................................................................................................12
8 Appendix ............................................................................................................................................13
8.1 FCC notice...................................................................................................................................................................13
Puro® Thermal Direct Printer YP-DP1 Table of contents
Minebea Intec EN-1
1 Introduction
1.1 Read the manual
-Please read this manual carefully and completely before using the product.
-This manual is part of the product. Keep it in a safe and easily accessible location.
1.2 This is what operating instructions look like
1. - n. are placed before steps that must be done in sequence.
1.3 This is what lists look like
-indicates an item in a list.
1.4 This is what menu items and softkeys look like
[ ] frame menu items and softkeys.
Example:
[Start]- [Applications]- [Excel]
1.5 This is what the safety instructions look like
Signal words indicate the severity of the danger involved when measures for preventing
hazards are not followed.
DANGER
Warning of personal injury
DANGER indicates death or severe, irreversible personal injury which will occur if the
corresponding safety measures are not observed.
Take the corresponding safety precautions.
WARNING
Warning of hazardous area and/or personal injury
WARNING indicates that death or severe, irreversible injury may occur if appropriate
safety measures are not observed.
Take the corresponding safety precautions.
CAUTION
Warning of personal injury.
CAUTION indicates that minor, reversible injury may occur if appropriate safety
measures are not observed.
Take the corresponding safety precautions.
is placed before a step.
describes the result of a step.
Puro® Thermal Direct Printer YP-DP1 1 Introduction
EN-2 Minebea Intec
NOTICE
Warning of damage to property and/or the environment.
NOTICE indicates that damage to property and/or the environment may occur if
appropriate safety measures are not observed.
Take the corresponding safety precautions.
Note:
User tips, useful information, and notes.
1 Introduction Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-3
2 Safety instructions
2.1 General information
-The device may only be used as intended for printing tasks.
-Observe the operating limits of the device.
-Unplug the power cord from the mains supply before cleaning.
-Make sure that no liquid enters the device.
2.2 Incoming goods inspection
Check the contents of the consignment for integrity. Check the contents visually to
determine whether any damage has occurred during transport. If there are grounds for
rejection of the goods, a claim must be led with the carrier immediately. A Minebea Intec
sales or service organization must also be notied.
Check the contents of the consignment for integrity. Check the contents visually to
determine whether any damage has occurred during transport. If there are grounds for
rejection of the goods, a claim must be led with the carrier immediately. A Minebea Intec
sales or service organization must also be notied. Visit our website
http://www.puroscales.com or contact your dealer.
2.3 Before operational startup
NOTICE
Perform visual inspection.
Before operational startup as well as after storage or transport, inspect the product
visually for signs of mechanical damage.
The product should not be put into operation if it displays signs of visible damage
and/or is defective.
Puro® Thermal Direct Printer YP-DP1 2 Safety instructions
EN-4 Minebea Intec
3 Device description
3.1 Overview
1 Paper compartment cover
2 Frame
3 SEL key
4 LF key
5 Paper compartment
6 Printhead
7 Display light
8 Reserve compartment
9 Interface connection RS-232
10 Power connection
11 ON/OFF switch
3 Device description Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-5
3.2 Dimensions
3.2.1 Paper format
Paper type Thickness Width Diameter
Thermal paper 0.06–0.08 mm 57±0.5 mm Max. 50 mm
Puro® Thermal Direct Printer YP-DP1 3 Device description
EN-6 Minebea Intec
4 Device installation
4.1 Electrical supply
(1) Power connection
WARNING
Warning of property damage and/or personal injury due to incorrect supply voltage.
The supplied power supply unit must be used without fail.
4.2 Data interface
(2) Interface connection
Use supplied connecting cable YP-CAS1.
4 Device installation Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-7
4.3 Suspend printer
1. Drill two mounting holes spaced 93.5 mm apart in the desired position.
2. Screw in two screws.
3. Suspend the printer.
Puro® Thermal Direct Printer YP-DP1 4 Device installation
EN-8 Minebea Intec
Autres manuels pour Puro YP-DP1
2
Table des matières
Autres manuels Minebea Intec Imprimante
