Mindman MVE2-MPL 100 Manuel utilisateur
EtherNet/IP CC-Link IEFBPROFINET EtherCAT
Fieldbus System
User Manual E1.1.0
100 / 156 / 188 / 220
MVE2-MPL
Contents
1
1Review...............................................3
1.1 Manual structure........................ 3
1.2 Typography habits...................... 3
1.3 Symbol....................................... 3
1.4 Acronym..................................... 3
1.5 Viewing angle deviation............. 3
2Guide .................................................4
2.1 Module overview ....................... 4
2.2 Electrical connections ................. 4
3Technical Data.................................5
3.1 Operating conditions.................. 5
3.2 Electric data ............................... 5
3.3 Communication specications .... 5
4Dial Code Settings .........................6
4.1 IP setting.................................... 6
4.2 Protocal switch setting ............... 7
4.3 Coil number setting.................... 7
5Communication Module Data....8
5.1 Coil denition............................. 8
5.2 Enter diagnostic data.................. 9
5.3 Output data.............................. 10
6EtherNet/IP Communication
Conguration............................... 12
6.1 LED display and setting ............ 12
6.2 Integrated ................................ 14
7PROFINET Communication
Conguration............................... 20
7.1 LED display and setting ............ 20
7.2 Integrated ................................ 21
8EtherCAT Communication
Conguration............................... 26
8.1 LED display and setting ............ 26
8.2 Integrated ................................ 27
9CC-Link IEFB Communication
Conguration............................... 35
9.1 LED display and setting ............ 35
9.2 Integrated ................................ 36
Information
22
Warranty
All products manufactured by Mindman are under warranty regarding
defective materials for a period of one year, starting from the date of delivery
to the original purchaser.
Warning
Mindman assumes no liability for damages resulting from the use of this
product. Mindman reserves the right to change this manual at any time
without notice. The information published by Mindman is believed to be
accurate and reliable. However, no responsibility is assumed by Mindman for
its use, not for any infringements of patents or other rights of third parties
resulting from its use.
Copyright
Copyright © 2019 by Mindman Co., Ltd. All rights are reserved.
Trademark
The names used for identication only may be registered trademarks of their
respective companies.
Contact us
If there has any question, please contact Mindman right away. Thanks.
Review
1
3
1.1 Manual structure
1. Overview section
2. Basic safety information
1.2 Typography habits
List: Enumeration is displayed as a list with bullets.
• Vocabulary 1
• Vocabulary 2
Action: The action description is represented by a front triangle.
The result of the action is represented by an arrow.
Military action description 1
Action results
Military action description 2
The step program can also be displayed numerically in parentheses.
(1) Step 1
(2) Step 2
Syntax: Digit
Decimal numbers are displayed without additional indicators (e.g.,123), Hexadecimal
number display with additional indicator hex (Such as: 00hex) Or with prex "0X"
(Such as: 0×00)
Cross reference: Cross referencing indicates where additional information about this topic
can be found.
1.3 Symbol
Explanatory note: This symbol indicates a general note.
Pay attention: This symbol indicates the most important safety notice.
1.4 Acronym
FNI : Network interface
EMC : Electromagnetic compatibility
FE : Functional earthing
1.5 Viewing angle deviation
The product views and explanations in this manual may deviate from the actual product.
They only explain the materials used left and right.
1. Review
This manual is organized by organization, so the chapters are connected to each other.
I : Standard input
O : Standard output
CIEFB: CC-Link IE Field Basic
Guide 2
4
2.1 Module overview
2.2 Electrical connections
2. Guide
No. Name Code Description
1 Power connector PWR M12, A-Coded (male) 4PIN, communication module and solenoid
valvepower supply
2Bus communication
interface OUT M12, D-Coded (female) 4PIN, PROFINET, EtherNet/IP, EtherCAT, CIEFB
3Bus communication
interface IN M12
,
D-Coded (female)
4PIN
,
PROFINET
,
EtherNet/IP
,
EtherCAT
,
CIEFB
4 DIP switch −Protocol switching, IP addressand coil settings
5Identication board − Device identication board
6 LEDstatus indicator −Indicate running status
No. Function
1UA Solenoid valve power supply 24V
2 GND Valve terminal/solenoid valve ground 0V
3 US Valve island power supply 24V
4 GND Valve terminal/solenoid valve ground 0V
No. Function
1 Tx+ Send data +
2 Rx+ Receive data +
3 Tx- Send data -
4 Rx- Receive data -
1 2 3
4 5 6
RUN
ERR
L/A IN
L/A OUT
MS/SF
NS/BF
ACT1
LK1
ACT2
LK2
US
UA
PWR
X100
X100 X10
007F11
X1
ECT
90
PN
E/IP
E/IP PN
ECT CIE
CIE
INOUT
Power connector
1
2
3
41
2
3
4
Bus communication
interface (OUT / IN)
Technical Data
3
5
3.1 Operating conditions
3.2 Electric data
3.3 Communication specications
3. Technical Data
Item Parameter
Working temperature -10~+50°C
Working humidity 35~85%RH (No condensation)
Working atmosphere No corrosive gas
Storage temperature -20~+60°C
Withstand voltage 500 VAC (1 minute)
Insulation resistance 500 VDC, ≥10MΩ
Waterproof level IP54
Item Parameter
Power consumption of valve island
(Ius) ≤0.1A (21.6~26.4VDC)
Total powerconsumption of ≤4A (22.8~26.4VDC)
Output low level NPN(+COM)
Solenoid valve type Single circuit less than 600mA withsurge protection 24V
solenoid valve
Single load ≤0.4V
Item Parameter
Protocol PROFINET, EtherNet/IP, EtherCAT, CIEFB
Cable type Shielded twisted pair cable minimumSTP CAT5/STP CAT 5e,
in line with IEEE 802.3
Data transfer rate 100Mbps (PROFINET/ EtherCAT)
10Mbps/ 100Mbps (elf-adaptive EtherNet/IP, CIEFB)
Number of outputcoils Up to 48 channels
File format PROFINET:XML
EtherCAT:XML
EtherNet/IP: EDS
CIEFB: CSPP
Dial Code Settings 4
6
4.1 IP setting
4. Dial Code Settings
The default gateway under different protocols as shown in the table below. Set the last
digit of the IPaddress by dialing.
EtherNet/IP protocol
Dial code to set the last digit of IP to X100=1, X10=2, X1=3,
and the IP address under is 192.168.1.123
CIEFB protocol
Dial code to set the last digit of IP to X100=6, X10=2, X1=3,
and the IP address under 192.168.3.123 needs to subtract 500
Letter of agreement Default gateway
EtherNet/IP 192.168.1.1
PROFINET Invalid
EtherCAT Invalid
CIEFB 192.168.3.1
X100 X10 X1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
X100 X10 X1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
Dial Code Settings
4
7
4.2 Protocal switch setting
4.3. Coil number setting
The color of LED_V9 above the DIP switch X100 indicates the current protocol
Steps:
1. The equipment is powered off, dial 900;
2. Power on the equipment and wait for 15s;
3. The equipment is powered off, and the dialing setting protocol is carried out
according to the above table
4. Power on the equipment and wait for 30s; The device is powered off,
dial the corresponding IP address (PROFINET, EtherCAT are invalid);
1. The equipment is powered off, dial code 950；
2. Power on the device and wait for the green light inside the dial to ash;
3. After the green light ashes, turn the dial switch to set the number of coils
(3S after stopping dialing, the set value takes effect)
To
4. Power off the device, dial the corresponding IP address
(PROFINET, EtherCAT are invalid);
X100
LED_V9
X10 X1
No. X100 X10 X1 Letter of agreement LED_V9
1 0~2 0~9 0~9 EtherNet/IP Green
2 3 0 0 PROFINET Orange
3 4 0 0 EtherCAT blue
4 5~7 0~9 0~9 CIEFB white
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
Communication Module Data 5
8
5.1 Coil denition
5. Communication Module Data
As shown in the gure, dene the upper coil as A1~A16 from left to right;
thelower coil as B0…B16 from left to right;
A1
B1
A2
B2
A3
B3
A4
B4
A16
B16
................
................
Communication Module Data
5
9
5.2 Enter diagnostic data
Byte Bit Remark
7 6 5 4 3 2 1 0
0− − −
US over-
voltage
UA over-
voltage
Operating
temp.
US under-
voltage
UA under-
voltage
−
1 B3 A3 B2 A2 B1 A1 B0 A0
Short circuit
diagnosis
0 normal
1 short circuit
2 B7 A7 B6 A6 B5 A5 B4 A4
3 B11 A11 B10 A10 B9 A9 B8 A8
4 B15 A15 B14 A14 B13 A13 B12 A12
5 B19 A19 B18 A18 B17 A17 B16 A16
6 B23 A23 B22 A22 B21 A21 B20 A20
7 B3 A3 B2 A2 B1 A1 B0 A0
Open circuit
diagnosis
0 normal
1 short circuit
8 B7 A7 B6 A6 B5 A5 B4 A4
9 B11 A11 B10 A10 B9 A9 B8 A8
10 B15 A15 B14 A14 B13 A13 B12 A12
11 B19 A19 B18 A18 B17 A17 B16 A16
12 B23 A23 B22 A22 B21 A21 B20 A20
EtherNet/IP
,
PROFINET
,
EtherCAT protocol
Ce manuel convient aux modèles suivants
3
Table des matières
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
