Miller RCCS-5 Manuel utilisateur

OWNER’S MANUAL OM-2806 188764G

2017−02

RCCS-5 (043718), RCCS-14 (043688), RCCS-6M (13Ft. 3in.) (195184),

And RCCS-6M (26Ft. 6in.) (195503)

DANGER! −Indicates a hazardous situation which, if not

avoided, will result in death or serious injury. The possible

hazards are shown in the adjoining symbols or explained

in the text.

Fsafe1 2013-10

Beware of electric shock from wiring. Disconnect input

power before installing this kit. Reinstall all panels and

covers.

Fsafe7 2013-10

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible ha-

zards are shown in the adjoining symbols or explained in

the text.

Wear safety glasses with side shields.

Fsafe8 2013-10

NOTICE Indicates statements not related to personal injury.

Indicates special instructions.

Fsafe3 2013-10

CALIFORNIA PROPOSITION 65 WARNINGS

Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in

some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm.

Wash hands after use.

Fsafe4 2013-10

SECTION 1 −INSTALLATION AND OPERATION

.The RCC (Rotary Current And Contactor Control) is equipped with a 14-pin, 5-pin, or a 6−pin plug for connection to the welding power source.

Contact your local distributor for correct adapter if plug does not mate with receptacle on welding power source.

!Be sure remote control is turned

all the way off before turning on

or off the welding power source.

1 Torch

2 Hook And Loop Straps

3 Current And Contactor Control

Actuator

Begin turning actuator in the Increase

direction as shown to close contactor,

and energize the welding power

source. Continue turning actuator to

increase current level up to that set

on the welding power source Current

Control.

Turn actuator in the Decrease

direction as shown to reduce the

current output to zero, and turn off the

contactor.

Secure control to torch with velcro

straps.

4 RCC (Rotary Current And

Contactor Control)

5 14-Pin, 5-Pin Or 6-Pin Plug PLG2

Connect PLG2 to matching

receptacle on welding power source

as follows: align keyway, insert plug,

and tighten threaded collar.

802020

Increase

Decrease

Figure 1-1. Installing And Operating An RCC Control

OM-2806 Page 2

SECTION 2 −ELECTRICAL DIAGRAMS

Figure 2-1. Circuit Diagram For RCCS-5 And RCCS-14 SA-151313-B

Figure 2-2. Circuit Diagram For RCC-6M Control 208592-A

OM-2806 Page 3

SECTION 3 −PARTS LIST

Ref. 802274-A / Ref. 208594-A

Ref. 157614 K / Ref. 802274 / Ref. 208594-A

678

10 11

RCCS-5

RCCS-14

567

10 11

Figure 3-1. Complete Assembly (RCCS-5 Shown)

Figure 3-2. Complete Assembly (RCCS-14 Shown)

DescriptionPart No.

uantity

Item

No. RCCS-5

Dia

Mkgs. Model RCCS-14

1 278463 Cable,Control Remote 26 Ft 6 In (5−Pin) (Includes) 1.................. .... ....

1 278460 Cable, Control Remote 26 Ft 6 In (14−Pin) (Includes) 1.................. .... .............

2 PLG2 144310 Housing Plug+Pins 1...... ..... ...... .........................................

2 PLG2 039273 Connector 1...... ..... ...... ......................................

3 070584 Tubing 1.................. ...... ..........................................

4 039685 Connector 1.................. ...... ......................................

5 176088 Tubing 1.................. ...... ..........................................

6 278464 Cable 1 1.................. ...... .......................................... ........

7 080286 Tubing 1 1.................. ...... ......................................... ........

8 209313 Connector 5 5.................. ...... ...................................... ........

9 PLG1 209314 Connector 1 1...... ..... ...... ...................................... ........

10 216384 Screw 3 3................. .... ............................................ ........

11 185419 Handle, Cover 1 1................. .... .................................... ........

12 229261 Circuit Card Assy 1 1................. .... ................................. ........

13 185418 Handle, Base 1 1................. .... ..................................... ........

14 155146 Sponge, Neoprene 1 1................. .... ................................ ........

151314 Strap 2 2.................... .... ............................................ ........

Use only Manufacturer’s Suggested Replacement Parts. Model number required when ordering parts.

OM-2806 Page 4

208594-B / Ref. 802274-A

Figure 3-3. Complete Assembly RCCS-6M Shown

DescriptionPart No. Quantity

Item

No.

Dia

Mkgs. RCCS-6M

1 PLG2 278462 Cable, Control Remote 13 Ft 3 In (6−Pin) (Includes) 1...... ..... .... ... ...........

1 PLG2 278461 Cable, Control Remote 26 Ft 6 In (6−Pin) (Includes) 1...... ..... .... .. ...........

2 209313 Connector 5.................. .... ...................................................

3 PLG1 209314 Connector 1...... ..... .... ...................................................

4 216384 S crew 3.................. .... ......................................................

5 185419 Handle, Cover 1.................. .... ................................................

6 229261 Circuit Card Assy 1.................. .... .............................................

7 185418 Handle, Base 1.................. .... ................................................

8 155146 Sponge, Neoprene 1.................. .... ............................................

9 084286 Tubing 1.................. .... ......................................................

151314 Strap 2.................... .... ........................................................

Use only Manufacturer’s Suggested Replacement Parts. Model number required when ordering parts.

Notes

Ce manuel convient aux modèles suivants

Autres manuels Miller Système de soudage

Miller

Miller Air Pak Manuel utilisateur

Miller

Miller big blue 700x duo pro Manuel utilisateur

Miller

Miller XMT 450 CC/CV Manuel utilisateur

Miller

Miller Millermatic 255 Manuel utilisateur

Miller

Miller Bobcat 260 Manuel utilisateur

Miller

Miller BOC Migmatic 250 Manuel utilisateur

Miller

Miller Dimension ArcReach NT 450 Manuel utilisateur

Miller

Miller Trailblazer 302 Diesel Manuel utilisateur

Miller

Miller XMT 350 MPa Manuel utilisateur

Miller

Miller Syncrowave 500 Manuel utilisateur

Miller

Miller Deltaweld 350 Manuel utilisateur

Miller

Miller SuitCase 8RC Manuel utilisateur

Miller

Miller Big Blue 450 Duo CST Manuel utilisateur

Miller

Miller Auto-Continuum 350 CE Manuel utilisateur

Miller

Miller SSW-2020ATT Manuel utilisateur

Miller

Miller CST 400 Manuel utilisateur

Miller

Miller Swingarc DS-74S/D Manuel utilisateur

Miller

Miller AG-BAG G6060 Manuel utilisateur

Miller

Miller Hydracool 1 CE Manuel utilisateur

Miller

Miller Continuum 350 Manuel utilisateur

Miller

Miller Axcess E 300 Manuel utilisateur

Miller

Miller SPECTRUM 750 Manuel utilisateur

Miller

Miller Gold Star 140 Manuel utilisateur

Miller

Miller HF-15-1 Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur