Miller RUNNING GEAR Manuel utilisateur

DO NOT OPERATE THIS EQUIPMENT

UNTIL THIS MANUAL

HAS BEEN READ AND UNDERSTOOD.

RUNNING GEAR

OPERATOR'S MANUAL

Miller-St. Nazianz, Inc.

P.O. Box 127

511 East Main St.

ST. NAZIANZ, WI 54232

920-773-2121

FAX: 920-773-1200

12.10811 4/05

The serial number for this unit is located on the Left Rear Bolster diagonal.

Miller-St. Nazianz reserves the right to make improvements in design or changes

in specifications at any time, without incurring any obligation to owners of units

previously sold.

IDENTIFYING TERMS

"LEFT" and "RIGHT" are determined from a position standing at the rear of the

unit looking toward the direction of travel. "FRONT" is the leading end and

"REAR" is the trailing end when the tractor is traveling forward.

WARRANTY REGISTRATION

The DELIVERY AND WARRANTY REGISTRATION CARD found in this manual

must be completed and signed to validate your warranty protection. You must

read and understand the places where you attest to having received instructions

as to care, adjustments, safe operation and applicable warranty policy. The

terms and conditions of the warranty are specified on the inside back cover of

this manual.

GENERAL INFORMATION

The purpose of this manual is to assist the operator in maintaining and operating

the Running Gear. Read it carefully; it furnishes information and instructions that

will help you achieve years of dependable service.

Each section of this manual is clearly identified and is divided into smaller

sections.

All replacement parts should be obtained from, or ordered through your dealer.

Give complete information when ordering service parts including the model

number and serial number. Record numbers in the space provided as a handy

record for quick reference.

Model No. Serial No.

TABLE OF CONTENTS

General Information .......................................... Inside Front Cover

Table of Contents ......................................................................... 1

Pre-Delivery/Delivery Check List .................................................. 2

Safety Precautions .................................................................... 3,4

Decal Location .............................................................................. 4

Lubrication .................................................................................. 4,5

Torque Specifications ................................................................... 6

Set-up & Assembly .................................................................... 7,8

Adjustments .................................................................... 9,10,11,12

Specifications.............................................................................. 13

Optional Features & Accessories ...........................................14,15

Warranty ............................................................ Inside Back Cover

RUNNING GEAR

PRE-DELIVERY CHECK LIST

After the Running Gear has been completely

set-up, check to be certain it is in correct running

order before delivering it to the customer. The

following is a list of points to inspect. Check off

each item as you have made the proper

adjustments and found the item operating

satisfactorily. Any adjustment must be made

according to specifications defined in this manual.

[] All grease fittings have been lubricated. See

“Lubrication” section in this manual.

[] All mechanisms are operating trouble free.

[] All bolts and other fasteners are tight and

torqued per torque specifications. Page 6.

Dealer’s

Name

Signature of Pre-Delivery Inspector

Date of Inspection

Model No.

Serial No.

DELIVERY CHECK LIST

The following check list is an important

reminder of valuable information that MUST be

passed on to the customer at the time the unit is

delivered. Check off each item as you explain it to

the customer.

[] Give the customer his Operator’s Manual.

Instruct them to be sure to read and completely

understand its contents BEFORE attempting to

operate the unit.

[] Explain the warranty.

[] Explain and review with the customer the

Safety Precautions section of this manual.

[] Explain and review with the customer the

Operating and Safety Equipment section of this

manual.

[] Explain that regular lubrication and proper

adjustments are required for continued proper

operation and long life. Review with the customer

the Maintenance and Adjustments sections of this

manual.

[] Complete the Delivery Registration Card and

have customer sign it and return it to Miller-St.

Nazianz, Inc.

I acknowledge that above points were reviewed

with me at the time of delivery.

Customer’s Signature

Date Delivered

(Customer Copy)

RUNNING GEAR

PRE-DELIVERY CHECK LIST

After the Running Gear has been completely

set-up, check to be certain it is in correct running

order before delivering it to the customer. The

following is a list of points to inspect. Check off

each item as you have made the proper

adjustments and found the item operating

satisfactorily. Any adjustment must be made

according to specifications defined in this manual.

[] All grease fittings have been lubricated. See

“Lubrication” section in this manual.

[] All mechanisms are operating trouble free.

[] All bolts and other fasteners are tight and

torqued per torque specifications. Page 6.

Dealer’s Name

Signature of Pre-Delivery Inspector

Date of Inspection

Model No.

Serial No.

DELIVERY CHECK LIST

The following check list is an important

reminder of valuable information that MUST be

passed on to the customer at the time the unit is

delivered. Check off each item as you explain it to

the customer.

[] Give the customer his Operator’s Manual.

Instruct them to be sure to read and completely

understand its contents BEFORE attempting to

operate the unit.

[] Explain the warranty.

[] Explain and review with the customer the

Safety Precautions section of this manual.

[] Explain and review with the customer the

Operating and Safety Equipment section of this

manual.

[] Explain that regular lubrication and proper

adjustments are required for continued proper

operation and long life. Review with the customer

the Maintenance and Adjustments sections of this

manual.

[] Complete the Delivery Registration Card and

have customer sign it and return it to Miller-St.

Nazianz, Inc.

I acknowledge that above points were reviewed

with me at the time of delivery.

Customer’s Signature

Date Delivered

(Dealer Copy)

Good safety practices dictate that you never tow an implement unless the towing

vehicle weighs at least one-and-one half (1-1/2) times the weight of the towed

implement and its load. For any public highway travel and to be in compliance

with this rule, be sure that your tractor or truck is heavy enough to counterbal-

ance the total (loaded) weight of the towed implement(s).

DO NOT travel on public highways unless adequate warning devices are used to

alert other drivers.

DO NOT drive too close to ditches or creeks; be sure surrounding ground has

adequate strength to support the weight of the loaded running gear.

DO NOT attempt to ride on the pole of the running gear.

DO NOT tow running gear faster than 20 mph.

DO NOT tow running gears in tandem on public roads.

ALWAYS use a safety or locking hitchpin.

ALWAYS keep the towing vehicle in gear when descending steep grades.

ALWAYS travel slowly around curves and along sidehills to prevent tipping.

BE SURE the tires are properly and evenly inflated at all times.

BE SURE the wheel nuts and other fasteners are kept securely tightened at all

times.

ALWAYS follow state and local regulations regarding a safety chain and auxiliary

lighting when towing farm equipment on a public highway. Be sure to check with

local law enforcement agencies for your own particular regulations. Only a

safety chain (not an elastic or nylon/plastic tow strap) should be used to retain

the connection between the towing and towed machines in the event of separa-

tion of the primary attaching system.

Block the tires, front and back, so that the running gear will not roll when discon-

necting from the towing vehicle.

Before you attempt to operate this running gear, read and study the

following safety information. In addition, make sure that every individual

who operates or works with this equipment, whether family member or

employee, is familiar with these safety precautions. The Operator's Manual

warns you of dangers and should be read and observed closely.

WARNING

SAFETY PRECAUTIONS

This symbol is used to call your attention to instructions

concerning your personal safety. Be sure to observe and

follow these instructions. Take time to be careful.

SAFETY PRECAUTIONS

WARNING

To ensure continued safe operation, replace damaged or worn-out parts with

genuine Miller service parts, before attempting to operate equipment.

DECAL LOCATION

LUBRICATION

GREASING

It is well to remember that a sufficient amount of oil or grease will prevent

excessive part wear and early failure. Grease fittings are provided on the

running gear at several important pivot points. Fittings should be lubricated at

least four times a year. Use a good grade of lithium base grease. Wipe dirt from

the fittings before greasing to prevent any dirt from being forced into the bearings

or pivots. Replace any missing fittings. To minimize dirt build-up, avoid exces-

sive greasing.

NOTE: In addition to the fittings, inspect and repack the wheel bearings at least

twice a year. See "Wheel Bearings" on next page.

Grease Fitting Locations:

1. Drawbar vertical pivot

2. Front spindle pivot (each side)

3. Ball joints (4 places)

4. Drawbar horizontal pivot

5. Tandem pivot (each side on tandem units)

LUBRICATION (continued)

WHEEL BEARINGS

Type of Grease: Use a good grade of Lithium Base Wheel Bearing Grease.

Carefully raise and support each wheel as repacking is performed.

Remove the hub from the spindle. Inspect the inner and outer cups in the hub. Be

sure both cups are seated against the shoulders in the hub.

Pack the cones with grease. A pressure grease packer is recommended. To hand

pack cones, force grease under cage between rollers from large end of rollers until

grease shows at small end. Fill the hub with grease to I.D. of the cup race, then

place the cone into the cup. Make sure the cone is straight!

WARNING: Failure to correctly lubricate bearing and maintain proper

lubrication may result in bearing damage which could cause wheel to lock

and come off during operation.

Install grease seal. Support the seal so as not to bend the case during installation.

Use grease to lubricate the seal lip.

Place the hub on to the spindle. Rotate the hub while doing this so that the seal lip

does not fold under as the lip goes on the seat of the spindle.

Fill hub cavity with grease.

Place the outer cone on the spindle and into the cup.

Assemble the washer and nut onto the spindle and tighten the nut to 15-20 ft/lbs,

while rotating the hub. back off the nut until it aligns the next available slot with the

cotter pin hole. Install the cotter pin and bend around the nut. There should be

between .001" - .005" end play.

WARNING: Failure to back off adjusting nut may cause bearing to run hot

and be damaged. Wheel could then lock and come off during operation.

Grease inside of dust cover and install dust cover.

Lower the wheel to the ground and repeat for the other wheels.

TORQUE SPECIFICATIONS

NOTE: Use these torque values when tightening hardware (excluding: Lock-

nuts and Self-tapping, Thread Forming and Sheet Metal Screws) unless speci-

fied otherwise.

All torque values are in Lb-Ft except those marked with an * which are Lb-In (for

metric torque value Nm, multiply Lb-Ft value by 1.355 or Lb-In value by 0.113)

Table des matières

Autres manuels Miller Accessoires de soudage

Miller

Miller MobileArc Manuel utilisateur

Miller

Miller 301523 Manuel utilisateur

Miller

Miller MTL-20 Torches Manuel utilisateur

Miller

Miller Robotic Interface II Manuel utilisateur

Miller

Miller CoolBand II Manuel utilisateur

Miller

Miller S-74 Boom w/Drive Manuel utilisateur

Miller

Miller Axcess 675 Manuel utilisateur

Miller

Miller Weldcraft W-125 Micro Series Manuel utilisateur

Miller

Miller S-75S Manuel utilisateur

Miller

Miller AugmentedArc Manuel utilisateur

Miller

Miller S-74 MPa Plus Manuel utilisateur

Miller

Miller Infinity Series Manuel utilisateur

Miller

Miller CST 195 114 Manuel utilisateur

Miller

Miller Spoolmate 150 Manuel utilisateur

Miller

Miller SUITCASE 12RC Manuel utilisateur

Miller

Miller ArcStation Manuel utilisateur

Miller

Miller AFT-100 Manuel utilisateur

Miller

Miller ps-100 Manuel utilisateur

Miller

Miller A-200 Series Manuel utilisateur

Miller

Miller FieldPro Remote Manuel utilisateur

Miller

Miller Travel Master SB-10D Manuel utilisateur

Miller

Miller M-10 Manuel utilisateur

Miller

Miller WCC Control Manuel utilisateur

Miller

Miller 22A Manuel utilisateur

Manuels Accessoires de soudage populaires d'autres marques

Lincoln Electric

Lincoln Electric LT-7 Tractor Manuel utilisateur

Weco

Weco Trolley R Manuel utilisateur

Cornwell Tools

Cornwell Tools MMWC1 Manuel utilisateur

Dohle

Dohle ExOn2A Manuel utilisateur

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Manuel utilisateur

3M Speedglas 9100 Series Manuel utilisateur

Miller Electric

Miller Electric OM-842 Manuel utilisateur

Abicor Binzel

Abicor Binzel ABIMIG WT Series Manuel utilisateur

optrel

optrel lifeflip autopilot Manuel utilisateur

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Manuel utilisateur

Abicor Binzel

Abicor Binzel xFUME PRO Manuel utilisateur

Sealey

Sealey SR20.V2 Manuel utilisateur

iWeld

iWeld NORED EYE Manuel utilisateur

Sthor

Sthor 74483 Manuel utilisateur

Leister

Leister TWINNY T7 Manuel utilisateur

LAHTI PRO

LAHTI PRO L1540400 Manuel utilisateur

Lincoln Electric

Lincoln Electric K3091-1 Manuel utilisateur

Tregaskiss

Tregaskiss TOUGH GUN TT4E Manuel utilisateur