MiLAN MIL-S1000 Manuel utilisateur
MIL-S1000
User’s Manual
Copyright Statement
COPYRIGHT 1999
ALL RIGHT RESERVED. First Edition. Printed in Taiwan.
All trademarks are the properties of their respective owners.
No portion of this document may be reproduced, altered,
adapted or translated without the prior written approval.
Warranty
This information in this document is subject to change
without notice. We make no warranty of any kind regarding
this material, including, but not limited to, the implied
warranties or merchantability and fitness for a particular
purpose. Furthermore, we shall not be liable for errors
contained herein or for incidental or consequential damage
in connection with the furnishing, performance, or use of this
material.
FCC Statement
This equipment has been tested and found to comply with
the limits for a class A device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with instructions, may cause harmful
interference on radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case, the user will be requires to
correct the interference at the user’s own expense.
Table of Contents
Chapter 1 Introduction
Package Contents……….…………………………………….. 1-2
Device Description, Features and Capabilities …………… 1-3
MIL-S1000 Front and Rear Panels……….……………… 1-3
8 ports 10/100Base-TX Module…….……………………… 1-5
8 ports 10/100Base-TX Module Features …..….… 1-5
2 ports 100Base-FX Fiber Module………………….…… 1-8
2 ports 100Base-FX Fiber Module Features ….….. 1-9
4 ports 100Base-FX Fiber Module ………..…………… 1-11
4 ports 100Base-FX Fiber Module Features ………. 1-12
1000Base-SX/LX Fiber Module …………………………..1-14
1000Base-SX/LX Fiber Module Features ……….…..1-14
Chapter 2 Planning your Network
10Base-T Ethernet Network Guidelines……………………. 2-1
100Base-T Ethernet Network Guidelines…………………… 2-2
1000Base-SX and LX Network Guidelines…………………. 2-3
Network Planning………………………………………………. 2-3
Expanded Networks………………………………….……….. 2-4
10Base-TX Networks…………………………………….. 2-4
100Base-TX Networks…………………………………… 2-5
Collapsed Backbone Line…………………………………….. 2-6
Fileserver Link………………………………………………….. 2-7
Multiport Bridge with High-Bandwidth Backbone……….. 2-9
Chapter 3 Installation
Choosing A Location………………………………………….. 3-1
Rack Installation……………………………………………….. 3-2
Supplying Power………………………………………………. 3-3
Connecting the Switch..……………………………………... 3-4
Chapter 4 Module Install and Removed
Handling the Modules…………………………………………. 4-1
Module Setup and installation……………………………… 4-2
Installing the Modules………………………………………… 4-3
Installing 10/100Base-TX Modules…… ………………. 4-3
Installing 100Base-FX Modules…… …………………… 4-3
Installing 1000Base-SX/LX Modules…… …………….. 4-4
Removing the Modules…………………………………………. 4-4
Appendix A Pin and Cable Specification…………..…. A-1
Appendix B Technical Specification……………….…… B-1
Chapter 1 Introduction
MIL-S1000 switches are multi-speed network devices
combining Ethernet, Fast Ethernet and Gigabit Ethernet
capabilities in a single compact, rack-mountable cabinet.
Combining 10Mbps Ethernet, 100Mbps Fast Ethernet and
Gigabit Ethernet interfaces in one unit allows these
switches to unclog existing LANs and provide a path to
efficient, high-speed networking.
The MIL-S1000 switch is a combination of a 4-slot host
cabinet which accepts 4 different media modules and One
RS-232 port for SNMP(Optional). A maximum configuration
of 32 x 10/100Base-Tx switched ports can be achieved
using 4×8 port 10/100Base-Tx modules. In the same way,
a maximum configuration of 32×10/100Base-TX or
16×100Base-FX ports or 4x 1000Base-SX can be
accommodated in the host cabling. Any of the above
modules can be integrated to give up to many different
configurations.
Package Contents
Power Cord Rubber Feet
Manual
Warrant
y
Car
d
Rack-Mount Ki
t
Figure 1-1. Package Contents
The MIL-S1000 package contains the following:
!MIL-S1000 switch
!AC power cord
!Rack mounting kit
!Four Rubber feet
!Warranty card
!User manual
Device Description, Features and Capabilities
MIL-S1000 Front and Rear Panels
This section describes the features on the front and rear
panels of the MIL-S1000 unit.
Figure 1-2. Front Panel
Figure 1-3. Rear Panel
All LED status indicators are located on the FRONT panel
of the switches. They provide a real-time indication of
system and operational status. The ports for connections to
other devices and networks are also on the front panels,
along with the crossover switches. The following sections
provide descriptions of the LED indicators and ports.
LED
Indicators Explanation
Power
The red power indicator is illuminated
when power is provided to the switch and
the switch is turned in the ON position.
Link/Activity
Green Link/Activity indicators are
illuminated when the switch detects a
connection to that port. The indicator
blinks when data is transmitted over the
network connected to that port.
When a port is not connected, the
indicator is off.
Full
Duplex/Col
Red Full Duplex/Col indicators
are illuminated when that port is
in full duplex mode. The indicator
is off when that port is in half
duplex mode.
When a collision occurs on the network
connected to a port, that Full Duplex/Col
indicator blinks.
100Mbps
Green 100Mbps indicators are illuminated
when the port is operating in 100Mbps
mode. The indicator is off when the port is
operating in 10Mbps mode.
"Power Port
The power port accepts the power plug.
"Power Switch
The power switch, located on the rear panel, controls the
power supply.
8 ports 10/100Base-TX Module
Figure 1-4. 8 port 10/100Base-TX Module
When installed into a MIL-S1000 switch, the 10/100Base-
TX Module provides 8 10/100Mbps Switch ports which can
connect the MIL-S1000 to a 10Mbps or 100Mbps switch or
end station.
8 Ports 10/100Base-Tx Module Features
"8 10/100Base-TX N-Way Switch ports.
"Conforms to IEEE 802.3 10Base-T and IEEE 802.3u
100Base-TX and IEEE 802.3x standards
"Store and forward switch architecture for abnormal
packet filtering
"Support for half and full duplex on all ports
"Backplane up to 2.4Gbps
"2M memory Buffer support
"Automatic address learning with 12K address entry
storage
"Filtering and forwarding rate of 14,880~148,800
packets per second
Table des matières
Autres manuels MiLAN Routeur réseau
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité