MikroTik RB800 Manuel utilisateur

RouterBOARD 800

Quick Setup Guide and Warranty Information



Assembling the Hardware

First use of the device:

• Insert the MiniPCI cards. RouterBOARD 800 provides

four MiniPCI slots and one miniPCI-e slot. SIM slot is

not provided, so this slot can't be used with 3G cards.

• (Optional) attach a daughterboard for additional

Interfaces

• Connect antenna cables to the MiniPCI cards.

• Install the device in a case

• Plug in power cable to turn on the board

• If installing this device in an outdoor location, ensure

proper grounding is installed as well.

Powering

The board accepts powering from either the power jack or

the LAN1 Ethernet port:

●direct-input power jack J14 (5.5mm outside and 2mm

inside diameter, female, pin positive plug) accepts

10..56 V DC.

●LAN1 Ethernet port J12 accepts 38..56 V DC input (at

the RouterBOARD. Higher voltage needed to

compensate for power loss on long cables; 48V

suggested) from Power over Ethernet injectors. RB800

supports 802.3af PoE standard powering.

The maximum output of the power supply to the

extensión cards is normally at about 25W (7.5A at 3.3V),

however with appropriate cooling, the onboard power

supply is capable to provide higher power output to the

extension cards. Without load and extension cards, RB800

consumes ~8.2W.



Booting process

First, RouterBOOT loader is started. It displays some useful information on the onboard RS232C asynchronous serial port. The serial

port is set by default to 115200bit/s, 8 data bits, 1 stop bit, no parity. Note that the device does not fully implement the hardware

(RTS/CTS) flow control, so it is suggested to try to disable hardware flow control in the terminal emulation program in case the serial

console does not work as expected, and if it does not help, make a new cable using the pinout given in the MikroTik Online Wiki. The

loader may be configured to boot the system from the onboard NAND, and/or from network. See the respective section of User's

manual on how to configure booting sequence and other BIOS parameters.

DHCP or BOOTP (configurable in loader) protocols allow the RouterBOARD 800 series board to get an initial IP address, and provide

the address of a TFTP server to download an ELF boot image from. It is especially useful for software installation.

See the User's manual for more information. Note that you must connect the RouterBOARD you want to boot and the BOOTP/DHCP

and TFTP servers to the same broadcast domain (i.e., there must not be any routers between them – they must be on the same

Ethernet switch).

Extension Slots and Ports

●Three Gigabit Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or

cross-over cables for connecting to other network devices. The first Ethernet port accepts 38..56 V DC powering from a PoE injector

(802.3af PoE supported). The other two Ethernet ports do not support PoE powering.

●Four MiniPCI Type IIIA/IIIB ports with 3.3V power signaling.

●DB9 RS232C asynchronous serial port.



Operating System Support

Currently tested operating system is MikroTik RouterOS (starting from v4).



Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may

be reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS,

RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are

the property of their respective holders.

Hardware. MikroTikls SIA warrants all RouterBOARD series equipment for the term of one year from the shipping date to be free of

defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or

other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature.

If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair

issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik Latvia To return failed unit or

units to MikroTikls you must perform the following RMA (Return Material Authorization) procedure.

Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. Take into account that all

goods have one year warranty.

Instructions are located on our webpage here: http://rma.mikrotik.com

Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the

implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the

accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies, typographical or other

errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other

damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits.



Autres manuels pour RB800

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels MikroTik Routeur réseau

MikroTik

MikroTik LHGGM&EG18-EA Manuel utilisateur

MikroTik

MikroTik RouterBOARD 493 Manuel utilisateur

MikroTik

MikroTik RB433r3 Mode d'emploi

MikroTik

MikroTik cAP Manuel utilisateur

MikroTik

MikroTik RouterBOARD 751U-2HnD Manuel utilisateur

MikroTik

MikroTik CRS510-8XS-2XQ-IN Manuel utilisateur

MikroTik

MikroTik RouterBOARD Groove 2Hn Manuel utilisateur

MikroTik

MikroTik CCR1009 Series Manuel utilisateur

MikroTik

MikroTik RB911G-2HPnD-12S Manuel utilisateur

MikroTik

MikroTik RouterBOARD CCR2004-1G-12S+2XS Manuel utilisateur

MikroTik

MikroTik RouterBOARD 1000 Manuel utilisateur

MikroTik

MikroTik RB800 Manuel utilisateur

MikroTik

MikroTik SXT Lite5 ac Manuel utilisateur

MikroTik

MikroTik RouterBOARD 951G-2HnD Manuel utilisateur

MikroTik

MikroTik 750/GL Manuel utilisateur

MikroTik

MikroTik RouterBOARD Groove Manuel utilisateur

MikroTik

MikroTik RouterBOARD RB2011UAS-IN Manuel utilisateur

MikroTik

MikroTik RB750UPr2 Manuel utilisateur

MikroTik

MikroTik hAP ax3 Series Manuel utilisateur

MikroTik

MikroTik MANTBox 52 15s Manuel utilisateur

MikroTik

MikroTik RB912UAG-2HPnD Manuel utilisateur

MikroTik

MikroTik RBwAPG-60ad Manuel utilisateur

MikroTik

MikroTik Chateau LTE6 ax Manuel utilisateur

MikroTik

MikroTik CRS504 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur