MikroTik CCR2004-16G-2S+ Manuel utilisateur
CCR2004-16G-2S+
CCR2004-16G-2S+
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.
Quick start
Connect with your computer to the device;
Download the configuration tool ;https://mt.lv/winbox
Open the tab and connect to the device using MAC address,
Neighbors
192.168.88.1 is available on ether15 using a web browser;
Theuser name: , by default there is no password(or, for some models, check user and wireless passwords on the sticker).;
admin
To dupdate the device to the latest software version ownload the latest RouterOS software from ;https://mikrotik.com/download
Choose ARM64 packages, and save them to your computer;
Return to the WinBox and upload downloaded packages;
Restart the device.
Powering
The device has dual integrated power supply units AC 100-240V with standard IEC compatible sockets with Maximum power consumption of 48 W.
1.
2.
Configuration
The Ethernet port 15 has a default IP address for connecting: 192.168.88.1. The username is admin and there is no password. The device doesn't have
any other configuration applied by default, please set up WAN IP addresses, user passwords, and update the device. RouterOS includes many
configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to the possibilities: https://mt.lv
. In case the IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address of the device from the /help https://mt.lv/winbox
LAN side
For recovery purposes, it is possible to boot the device for reinstallation, see a section Reset button.
Specifications
Product code CCR2004-16G-2S+
CPU AL32400 1.7 GHz
CPU architecture ARM 64bit
CPU core count 4
Size of RAM 4 GB
RAM type DDR4
Storage 128 MB, NAND
Number of 1G Ethernet ports 16
Number of 10G SFP+ ports 2
USB port 1 (3.0 type A)
Operating system RouterOS (License level 6)
Switch chip model 88E6191X, 88E619X
Dimensions 443 x 210 x 44 mm
Operating temperature -20°C to +60°C
Reset button
The reset button has two functions:
Hold this button during boot time until the LED light starts flashing, release the button to reset the RouterOS configuration.
Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers.
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
Useful for RouterBOOT debugging and recovery.
Mounting
The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack mounts, or it can be placed on the desktop.
Use a Phillips screwdriver to attach rackmount ears on both sides of the device if designated use is for rackmount enclosure:
Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown on the picture to the right;
2.
3.
Place the device in rackmount enclosure and align with the holes so that the device fits conveniently;
Tighten screws to secure it in place.
The device has no protection from water contamination, please ensure the placement of the device in a dry and ventilated environment. We recommend
Cat6 cables for our devices.
Included Parts
PLUG1-2_ EU/US power cord, JL3-JL38C (D03+QT3) H05VV-F 3x0.75mm2 1.83m
SET1_ Fastening set K-57
CASE3-4_ 1U rackmount bracket white
Operating System Support
The device supports RouterOS software with version number v7.0.4 at or above what is indicated in the RouterOS menu /system resource. Other
operating systems have not been tested.
Safety Notice
Electric shock hazard. This equipment is to be serviced by trained personnel only.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in aresidential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as in
designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated
disposal sites in your area.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.
Innovation, Science and Economic Development Canada
This device complies with Industry Canada's license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
This ClassBdigital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-003 (B) / NMB-003 (B)
UKCA marking
Eurasian Conformity Mark
Информация о дате изготовления устройства указана в конце серийного номера на его наклейке через дробь. Первая цифра означает номер
года (последняя цифра года), две последующие означают номер недели.
Изготовитель: Mikrotikls SIA, Aizkraukles iela 23, Riga, LV-1006, Латвия, . Сделано в Китае, Латвии или Литве. Cм. на [email protected]
упаковке.
Для получения подробных сведений о гарантийном обслуживании обратитесь к продавцу. Информация об импортерах продукции MikroTik в
Российскую Федерацию: https://mikrotik.com/buy/europe/russia
Продукты MikroTik, которые поставляются в Евразийский таможенный союз, оцениваются с учетом соответствующих требований и помечены
знаком EAC, как показано ниже:
Norma Oficial Mexicana
EFICIENCIA ENERGETICA CUMPLE CON LA NOM-029-ENER-2017.
La operacion de este equipo esta sujeta a las siguientes dos condiciones:
Es posible que este equipo o dispositivo no cause interferencia perjudicial y.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.
Fabricante: Mikrotikls SIA, Brivibas gatve 214i, Riga, LV-1039, Latvia.
País De Origen: Letonia; Lituania; China (Republica Popular); Estados Unidos De America; Mexico.
Por favor contacte a su distribuidor local para preguntas regionales específicas. La lista de importadores se puede encontrar en nuestra página de inicio –
.https://mikrotik.com/buy/latinamerica/mexico
CE Declaration of Conformity
Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039.
The full text of the EU Declaration of Conformity is available at the following internet address: https://mikrotik.com/products
Information contained here is subject to change. Please visit the product page on
www.mikrotik.com for the most up to date version of this
document.
Autres manuels pour CCR2004-16G-2S+
2
Table des matières
Autres manuels MikroTik Matériel réseau
MikroTik
MikroTik PL7411-2nD Guide de démarrage rapide
MikroTik
MikroTik nRAY Series Manuel utilisateur
MikroTik
MikroTik CRS310-1G-5S-4S+IN Manuel utilisateur
MikroTik
MikroTik GPEN11 Manuel utilisateur
MikroTik
MikroTik ATL LTE18 kit Manuel utilisateur
MikroTik
MikroTik cAP ax Manuel utilisateur
MikroTik
MikroTik Chateau LTE12 Manuel utilisateur
MikroTik
MikroTik 2004-1G-12S+2XS Manuel utilisateur
MikroTik
MikroTik LHG Lite60 Manuel utilisateur
MikroTik
MikroTik netFiber 9 Manuel utilisateur
MikroTik
MikroTik LHG LTE18 kit Manuel utilisateur
MikroTik
MikroTik RouterBOARD SXT G-2HnD Manuel utilisateur
MikroTik
MikroTik CCR2004-16G-2S+ Manuel utilisateur
MikroTik
MikroTik RouterBOARD 450 Series Manuel utilisateur
MikroTik
MikroTik FiberBox Plus Manuel utilisateur
MikroTik
MikroTik CSS610-8G-2S+IN Manuel utilisateur
MikroTik
MikroTik CRS112-8G-4S-IN Manuel utilisateur
MikroTik
MikroTik RBwAPG-60ad-A Manuel utilisateur
MikroTik
MikroTik RouterBOARD 711-5HnD Manuel utilisateur
MikroTik
MikroTik SXTsq Lite5 Manuel utilisateur
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
