MIKRODEV RTU Series Manuel utilisateur
DM100
HARDWARE MANUAL
•DM100
RTU Series
04 / 2022
MIKRODEV_HM_DM100_EN
v1.4
1
DM100 SERIES –HARDWARE MANUAL
CONTENTS
FIGURES LIST ..................................................................................................................................2
Preface ...........................................................................................................................................3
About Mikrodev .............................................................................................................................4
WARNING!......................................................................................................................................5
1DM100 GENERAL INFORMATION........................................................................ 6
1.1 GC0 Board Type Physical Interfaces............................................................. 6
1.2 GC3 Board Type Physical Interfaces............................................................. 7
1.3 General Device Specifications ..................................................................... 8
2INSTALLATION INFORMATION........................................................................... 9
2.1 Rail Installation ......................................................................................... 9
2.2 Expansion Installation...............................................................................10
3CONNECTION DIAGRAMS ................................................................................11
3.1 Supply Connection....................................................................................11
3.2 RS485 Serial Port .....................................................................................12
3.3 RS232 Serial Port .....................................................................................13
2
DM100 SERIES –HARDWARE MANUAL
FIGURES LIST
Figure 1 GC0 Board Type Connector and Physical Interface......................................... 6
Figure 2 GC3 Board Type Connector and Physical Interface......................................... 7
Figure 3 Mounting.................................................................................................. 9
Figure 4 Expansion Installation...............................................................................10
Figure 5 Power Connection Diagram........................................................................11
Figure 6 RS485 Serial Port Connection Diagram .......................................................12
Figure 7 RS232 Serial Port Connection Diagram .......................................................13
3
DM100 SERIES –HARDWARE MANUAL
Preface
Mikrodev DM100 RTU series are programmable control devices that are used in a wide
range of applications from process automation to building automation, from machine
automation to telemetry applications.
In this document, you can find information about the hardware specifications of Mikrodev
DM100 series RTUs.
Please follow our website www.mikrodev.com for the up to date version of the document.
4
DM100 SERIES –HARDWARE MANUAL
About Mikrodev
Since 2006, MIKRODEV has been developing and manufacturing industrial control and
communication products. MIKRODEV serves the system integrators in the public and
private sector, OEM and end users.
Our products are manufactured complying with the quality standards required by the
industrial automation industry and the quality of our products are proved on the field for
many years
MIKRODEV is one of the few companies in the world that has its own designed IEC
61131-3 compliant library for its programmable logic control devices. In addition, the
open, flexible, programmable SCADA solution developed by MIKRODEV is also available
to customers.
MIKRODEV products' performance and wide range of applications make them possible for
customers to achieve faster, simplified and cost-effective results.
5
DM100 SERIES –HARDWARE MANUAL
WARNING!
✓Please take care of the following issues when using Mikrodev devices.
✓Since the unit operates with 24 VDC (12-36 VDC) voltage, you should take care of
the voltage level that the unit is connected to. If a voltage above this voltage level
is applied, the device may be damaged and may be out of warranty.
✓Make sure that the energy connection of your device is connected to the ground
or to a properly grounded terminal.
✓Make sure that the environment in which your device is being used is free of
moisture, electric shock, vibration and dust.
✓Pay attention to the supply voltage and the connections of the product. Mikrodev
is not responsible for any issues due to power failure since there is no auxiliary
supply (UPS) on the device.
✓The fuse to be used must be a FF super fast type and current limit value 1A.
✓Do not use the device under conditions other than the environmental conditions
specified in the "Electrical Specifications" section (humidity, dust, liquid and
temperature, etc.)
✓Removing the warranty label on the product or removing the protective case will
void the warranty.
✓Products that are damaged, boxes have been changed and other brand labels are
affixed are not covered by the warranty.
✓The appliance must not be cleaned with solvents (thinner, benzine, acid etc.) or with
abrasive cleaning agents.
✓Only dry cloth should be used when cleaning the appliance.
✓Do not open the device by removing the case of the appliance, do not interfere
with the electronic components and circuits. There is no user-replaceable part
inside the device.
✓If there is a problem or malfunction on your device, it should only be repaired by
an authorized service. Installation and electrical connections must be made by
technical personnel in accordance with the instructions in the operating manual.
Failure to comply with these rules may result in death, serious injury or
property damage
6
DM100 SERIES –HARDWARE MANUAL
1DM100 GENERAL INFORMATION
1.1 GC0 Board Type Physical Interfaces
Figure 1 GC0 Board Type Connector and Physical Interface
1
Ethernet Port
10
RS485 Port 1 Connections
2
USB Port
11
SD Card Slot
3
System Power LED
12
Serial Port GND Connections
4
System Running LED
13
RS485 Port 2 Connections
5
System Error LED
14
Serial Port GND Connections
6
System Connection Status LED
15
RS232 Connections
7
RS485 Port 1 Data Transfer LED
16
N/A
8
RS485 Port 2 Data Transfer LED
17
Expansion Connector
9
N/A
18
Device Power (V+/V-) Connection
7
DM100 SERIES –HARDWARE MANUAL
1.2 GC3 Board Type Physical Interfaces
Figure 2 GC3 Board Type Connector and Physical Interface
1
Ethernet Ports
9
SD Card Slot
2
USB Port
10
RS485 Port 1 Connections
3
System Power LED
11
RS485 Port 1 GND Connections
4
System Running LED
12
RS485 Port 2 Connections
5
System Error LED
13
RS485 Port 2 GND Connections
6
System Connection Status LED
14
Expansion Connector
7
RS485 Port 1 Data Transfer LED
15
Device Power (V+/V-) Connection
8
RS485 Port 2 Data Transfer LED
8
DM100 SERIES –HARDWARE MANUAL
1.3 General Device Specifications
SPECIFICATION
ITEM
DESCRIPTION
Processor
Processor Architecture
ARM Cortex A7
Adressing Architecture
Little Endian Addressing
Electrical
Supply
24 VDC (12-48 VDC)
Power
<10W @ 24V DC
Real Time Clock
Integrated
Enviromental
Conditions
Operating Temperature
-25…+75 C
Storage Temperature
-30…+80 C
Humidity
5..95 RH
Memory
SD Card Support
Micro SD
Retentive Memory
56 MB
Program Memory
256 MBit
Communication
Ports
Board Type
GC0
GC3
Ethernet Port
1 Port, 10/100
Mbps
2 Ports, 10/100
Mbps
RS485
2 Port, ESD
Protection
2 Port, ESD
Protection
RS232
1 Port
USB
1 Port, Mini USB Type B
Expansion
Capacity
Din RAIL Type- CANBUS
Expansion Modules
Up to 512 I/O Points
9
DM100 SERIES –HARDWARE MANUAL
2INSTALLATION INFORMATION
2.1 Rail Installation
DIN Rail Mountage
First, the upper part of the device is mounted on the DIN rail. Then, with the help of the
springs behind the device, when a lightly force is applied to the lower part, the device
locates into the DIN rail easily and the montage is completed. (See Figure 2)
DIN Rail Demountage
To demount the device, firstly it is pulled from the bottom using flexibility of the spring,
the device is removed from the DIN Rail and the demounting is completed.
Figure 3 Mounting
Autres manuels pour RTU Series
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels MIKRODEV Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
