Mighty Seven PB-1310 Manuel utilisateur
1
1. The maximum recommended air pressure during operation must not exceed 90 psi
(6.3bar). Higher air pressure may create unsafe operating conditions for the tool and
the user.
2. The compressed air should be cooled and have a water lter installed at the outlet
end of the compressor. Even with a water filter installed, some water may still
condense in the piping or hose and will enter the tool mechanism causing premature
damage to the tool. Therefore, it is recommended to install an air filter-lubricator
device somewhere between the tool and the compressor.
3. Always use an air compressor of the proper capacity to operate each tool.
4. Clean the hose with a blast of compressed air before connecting the hose to the air
tool. This will prevent both moisture and dust inside the hose from entering the tool
and causing possible rust or malfunction.
1. Using these tools in any potentially explosive environment is strictly prohibited.
2. It is always recommended that these types of tools must be operated when standing
on a solid or rm location.
3. Always use these tools in a well ventilated area.
4. Slipping, stumbling and falling are the major causes of potential serious injury,
therefore, a clean and clutter free surface in the working area before operating the
tools is strongly recommended.
Read this manual carefully before installing, operating,
servicing or repairing.
Working environment:
Air supply and connection requirements:
2
Ideal system connection:
Piping diameters and length requirement:
The diameter ΦA required for the inlet pipe is recommended on the specication table.
The diameter ΦB required for the branch pipe (from to ) should be 2 times as large as ΦA. ΦB
= 2 x ΦA
The diameter ΦC required for the primary air supply (from to ) should be 3 times as large as ΦA.
ΦC = 3 x ΦA
The length for the inlet pipe should be less than 15 feet (4.5m).
3
1. This tool should only be used as a hand operated tool. It is powered by compressed air and is not
insulated against electric shock.
2. This tool is specially designed for riveting sheet metals together. Any application or use of this tool other
than what it is designed for is strictly prohibited.
3. High sound levels may cause hearing damage. Always wear hearing protection when operating this tool.
4. Wearing eye/face protection can reduce the danger of high-speed materials being ejected from tool use.
5. User must wear proper clothing. Loose clothing, long hair, stings, straps, belts and jewelry should not be
worn when operating this tool.
6. Make sure that the all the specications of the rivets to be used are compatible with this tool.
7. Check the protection against the ejecting of rivet stem in place and is operative.
8. Make certain to stand on a solid or rm location and keep body in well-balanced position while operating
this tool.
9. Always turn off the air supply and disconnect the air hose before changing rivet nose or making
adjustments on this tool.
10.Release the throttle lever to avoid danger if there is a failure of energy supply or when connecting or
disconnecting the air hose.
11.Prolonged use will cause user fatigue. Periodic breaks are recommended for user safety.
12.It is recommended to stop operating the tool whenever the user experiences discomfort, tingling or pain
during use.
13.Beware if the compressed air hose breaks unexpectedly, or is being connected or disconnected
improperly. This whipping action may cause injury.
Warning:
4
1.Riveter case
2.Hanging ring
3.Riveter nose piece
4.Hex driver
----------1PCS
--------1PCS
--2SET
------------2PCS
Parts Description
5
All Parts Function Illustration
Hanging Ring
Riveter nose piece
Forward trigger (Rivet)
Reverse trigger(Rivet)
Exhaust Silencer
Air pressure regulator
6
Installation
Step 1: Install the part 4Put
the Hex driver in the middle of
the axis.
Note: The Hex connector
hole should be aligned with
the spindle.
Step 2: Install the part 3The
riveter nose piece.
Note: After the insertion of
the Hex driver, it should be
perfectly aligned with the rivet
head.
4
3
7
Step 3: Push down the
outside collar of the chuck
and insert the mandrel head.
Note: That it is installed
properly there will be a small
sound of the parts clicking
together.
Step 4: Before using, please
verify and check the correct
operation and installation of
the parts.
8
Step 5: When air pressure exceeds 90PSI (6.3BAR), please adjust the pressure valve to the
recommended operating level to avoid any problem.
The use of over pressure will reduce the lifetime of the tool and may cause injury to the user.
Note: Please refer to our specications for the suggested pressure values.
9
Gear M8~M10 400 7.8 90(6.3) ------ 1.74 2.79 3/8" 86.0 1.6
Gear M8~M10 400 7.8 90(6.3) ------ 1.74 2.79 3/8" 86.0 1.6
Gear M8~M10 400 7.8 90(6.3) ------ 1.74 2.79 3/8" 86.0 1.6
PB-1310
PB-1310
PB-1310
Free
Speed
Free
Speed
Free
Speed
Capacity
Capacité
Capacity
Structure
Structure
Structure
Ave. Air
Consumption
Cons. D'air
moyenne
Ave. Air
Consumption
Air
Pressure
Pression
Air
Pressure
Overall
Length
Net
Weight
Poids
Nettogewicht
Net
Weight
Poids Tuyau
d'air
Empf.
Luftschlauch
Niveau
sonore
Schalldruckpegel
Niveau de
vibration
Vibrationsniveau
Nettogewicht
R.P.M
R.P.M
R.P.M
mm
mm
mm
CFM
CFM
CFM
PSI(bar)
PSI(bar)
PSI(bar)
mm(Inch)
mm(Inch)
mm(Inch)
kg
kg
kg
Uncertainty K=0.5a if a≤5 m/s² or K=0.4a if a>5 m/s²
Uncertainty K=0.5a if a≤5 m/s² or K=0.4a if a>5 m/s²
Uncertainty K=0.5a if a≤5 m/s² or K=0.4a if a>5 m/s²
Longueur
Référence
Artikel-Nr.
10
Gear M8~M10 400 7.8 90(6.3) ------ 1.74 2.79 3/8" 86.0 1.6
Gear M8~M10 400 7.8 90(6.3) ------ 1.74 2.79 3/8" 86.0 1.6
Gear M8~M10 400 7.8 90(6.3) ------ 1.74 2.79 3/8" 86.0 1.6
PB-1310
PB-1310
PB-1310
Free
Speed
Free
Speed
Free
Speed
Capacity
Capacité
Capacity
Structure
Structure
Structure
Ave. Air
Consumption
Cons. D'air
moyenne
Ave. Air
Consumption
Air
Pressure
Pression
Air
Pressure
Overall
Length
Net
Weight
Poids
Nettogewicht
Net
Weight
Poids Tuyau
d'air
Empf.
Luftschlauch
Niveau
sonore
Schalldruckpegel
Niveau de
vibration
Vibrationsniveau
Nettogewicht
R.P.M
R.P.M
R.P.M
mm
mm
mm
CFM
CFM
CFM
PSI(bar)
PSI(bar)
PSI(bar)
mm(Inch)
mm(Inch)
mm(Inch)
kg
kg
kg
Uncertainty K=0.5a if a≤5 m/s² or K=0.4a if a>5 m/s²
Uncertainty K=0.5a if a≤5 m/s² or K=0.4a if a>5 m/s²
Uncertainty K=0.5a if a≤5 m/s² or K=0.4a if a>5 m/s²
Longueur
Référence
Artikel-Nr.
Table des matières
Autres manuels Mighty Seven Outils de rivetage
