MGL Avionics IEFIS Lite Manuel utilisateur

MGL Avionics iEFIS Lite

Getting started guide

Connect EFIS Power cable to EFIS panel and supply 12V and ground to supply input via

avionics master switch.

Connect the keep alive (KA)” wire permanently to the aircraft battery +12V terminal. This

connection should remain at all times.

Connect devices such as RDACs, AHRS and compass sensors to the CAN interface bus. See

installation manual for details. Do not forget to fit CAN bus termination resistors.

The EFIS panel should now be alive.

Press the menu button, select system setup” -> Standard system selections”.

Select your desired screen layout, engine and fuel monitoring options. You will complete the

engine and fuel individual setups in the Engine and fuel related setup menus”.

Connect pitot and static ports as needed. After final mounting of the panel allow the panel to

warm up for 10 minutes and then perform the zero ASI and AOA sensors” procedure in the

Internal and external sensor setup” menu (under system setup).

Verify correct airspeed indication before first flight. The minimum airspeed for indication is 27

knots.

Install the navigation database, maps and terrain data using the Install tasks menu”.

Install the GPS antenna and connect it to the panel You should have a valid position typically

in under one minute (Note: GPS reception may not be possible inside a hangar).

Please calibrate the touch screen to conform to your fingers anatomy and desired touch

position (relative to the pressure point of your finger). The easiest way to do this is to press

the second right rotary control towards the panel (past the detent), hold this and then switch

on the panel. It will start straight in touch screen calibration mode. Calibration is quick and

requires only 5 reference points.

Please refer to user and installation manuals for all devices used. The latest versions of these

manuals are available for download at www.MGLAvionics.co.za.

Please familiarize yourself with the operation of the EFIS and the many setups in the system.

Most of these setups will be done only once to set the system up to your needs.

Please ensure that all systems are working correctly, that installation has been performed to

required aircraft standards and that the pilot is familiar with the EFIS operation and is able to

use it correctly as reference for safe flight, including emergency procedures for partial or full

systems failure.

Ensure that adequate, high quality electrical power supply is available to the EFIS at all times,

including a suitable backup supply if needed.

Please keep your irmware updated to the latest available versions:

Your iEFIS panel contains an operating system and application program that will be updated

frequently as new functions are added or bugs are fixed.

These updates are available for free download from www.MGLAvionics.co.za

The update consists of a single file called "EXP3.BIN". This contains the complete operating

system as well as the EFIS application itself.

Download this file and copy it to the root folder of an SD micro card.

The SD micro card should preferably be freshly formatted to either FAT16 or FAT32

specification. You can perform this format using the functions provided in your PC.

Insert the SD micro card into your EFIS and switch on. The boot system in your EFIS should

detect the card and find the file. If the file checks out it will be installed. This process takes

about 5 seconds. The new system is then started.

You can delete the "EXP3.BIN" file after this from your SD card which is advisable as

otherwise the system will load and check the file every time you switch on to make sure it is

still the same that is installed. This will delay the start up by a few seconds and this can be

avoided.

Fly sa ely !

Table des matières

Autres manuels MGL Avionics Affichage avionique

MGL Avionics

MGL Avionics Stratomaster Maxi Single FF-3 Manuel utilisateur

MGL Avionics

MGL Avionics AV-2 Manuel utilisateur

MGL Avionics

MGL Avionics Stratomaster Maxi Single Flight II Manuel utilisateur

MGL Avionics

MGL Avionics Blaze EMS-2 Manuel utilisateur

MGL Avionics

MGL Avionics Stratomaster Maxi Single VSI-2 Manuel utilisateur

MGL Avionics

MGL Avionics Vega TP-3 Manuel utilisateur

MGL Avionics

MGL Avionics BAT-1 Manuel utilisateur

MGL Avionics

MGL Avionics Stratomaster Ultra L Guide de dépannage

MGL Avionics

MGL Avionics FF-1 Manuel utilisateur

MGL Avionics

MGL Avionics Stratomaster Smart Single EMS-503 Manuel utilisateur

MGL Avionics

MGL Avionics Stratomaster Maxi Single ALT-3 Manuel utilisateur

MGL Avionics

MGL Avionics Vega ASV-1 Manuel utilisateur

MGL Avionics

MGL Avionics FF-1 Manuel utilisateur

MGL Avionics

MGL Avionics Blaze ASV-2 Manuel utilisateur

MGL Avionics

MGL Avionics Blaze FLIGHT-3 Manuel utilisateur

MGL Avionics

MGL Avionics XTreme - EMS Manuel utilisateur

MGL Avionics

MGL Avionics Blaze TP-4 Manuel utilisateur

MGL Avionics

MGL Avionics Stratomaster Enigma Manuel utilisateur

MGL Avionics

MGL Avionics Stratomaster Maxi Singles GPS-1 Manuel utilisateur

MGL Avionics

MGL Avionics EFIS G2 Manuel utilisateur

Manuels Affichage avionique populaires d'autres marques

Smart Avionics

Smart Avionics PB-4 Manuel utilisateur

Midcontinent

Midcontinent SAM MD302 Manuel

Garmin

Garmin GI 275 Manuel utilisateur

Mid-Continent Instruments

Mid-Continent Instruments 4300 Series Manuel

Avidyne

Avidyne 700-00182 Series Manuel de service

Flybox

Flybox Oblo Manuel utilisateur

Garmin

Garmin GMA 350H Manuel

Garmin

Garmin G3X Touch Manuel

SANDIA aerospace

SANDIA aerospace SAFE 328 Manuel utilisateur

Lynx

Lynx Micro System Manuel utilisateur

SAC

SAC SA100 Manuel utilisateur

Garmin

Garmin GNC 420 Manuel utilisateur

Avidyne

Avidyne Entegra Manuel

Dynon

Dynon SkyView HDX System Document technique

Garmin

Garmin Cessna Caravan G1000 Guide de configuration

Barco

Barco MDU-254 Manuel utilisateur

PROXALERT

PROXALERT R5 Manuel

Garmin

Garmin Cessna Caravan G1000 Manuel utilisateur