Metrologic MS951 Mode d'emploi
METROLOGIC INSTRUMENTS, INC.
MS951 Hand-Held Laser Scanner
including all scanner configurations
Programming Guide
MLPN 2366
Printed in USA
November 1998
Locations:
USA Corporate Headquarters South America
Metrologic Instruments, Inc. Metrologic Instruments
90 Coles Road Rua Flórida 1.821, 5° Andar-Brooklin
Blackwood, NJ 08012 CEP 04571-090, São Paulo-SP,
BrasilCustomer Service: 1-800-ID-METRO Outside Brazil:
Tel: 609-228-8100 Tel: 55-11-5505-6568
Fax: 609-228-6673 Fax: 55-11-5507-2301
http://www.metrologic.com In Brazil:
Mailing Address: Metrologic do Brasil Ltda.
P.O. Box 307 Tel: 55-11-5505-2396
Bellmawr, NJ 08099-0307 Fax: 55-11- 5507-2301
Europe ASIA
Metrologic Instruments GmbH Metrologic Asia (PTE) Ltd.
Dornierstrasse 2 31, Kaki Bukit Road 3
82178 Puchheim b. #05-08,
Munich, Germany Techlink
Tel: 49-89-89018-0 Singapore 417818
Fax: 49-89-89019-200 Tel: 65-842-7155
Copyright
© 1998 by Metrologic Instruments, Inc. All rights reserved. No part of this work may
®
be reproduced, transmitted, or stored in any form or by any means without prior written
consent, except by reviewer, who may quote brief passages in a review, or provided for
in the Copyright Act of 1976.
Products and brand names mentioned in this document are trademarks of their
respective companies.
Table of Contents
Scope of the MS951 Programming Guide ........................... 1
Programming the Scanner ........................................ 2
Enter Program Mode ............................................ 3
Recall Defaults ................................................. 3
Laser Activation Range .......................................... 4
Laser Operation ................................................ 4
Same Symbol Re-Scan .......................................... 5
Identical Symbol Re-Scan Indicator ................................ 5
1 vs 2 Scan Buffers ............................................. 5
Decode Options ................................................ 6
Beeper Tones .................................................. 7
Audible Indicators for Communication Timeouts ...................... 8
RS-232 Interface ............................................... 9
RS-232 Parameter - Baud Rate .................................... 9
RS-232 Parameter - Parity ...................................... 10
RS-232 Parameter - Data Bits .................................... 10
RS-232 Parameter - Hardware Handshaking ........................ 11
RS-232 Parameter - Software Handshaking ......................... 11
Intercharacter Delay ............................................ 12
RS-232 Parameter - Scanning Control (DTR Signal) ................. 13
“DE” Disable Command ........................................ 13
Longitudinal Record Redundacy Check (LRC) ....................... 14
Record Header/Terminator Select .............................. 14, 15
UPC/EAN Identifiers ........................................... 16
Keyboard Wedge (KB) Interface .................................. 17
KB Parameter - Keyboard Type .................................. 17
KB Parameter - Keyboard Country Type ........................... 18
KB Parameter - Caps Lock Mode ................................. 20
KB Parameter - Alt Mode ....................................... 20
KB Parameter - Inter Scan Code Delay (AT and PS/2 Modes) .......... 21
KB Parameter - XT - Clean-Up Bit ............................... 21
Record/Header Terminator Select .............................. 22, 23
Intercharacter Delay ............................................ 23
KB Parameter - Special Features ................................. 24
OCIA Options ................................................ 25
IBM 46XX Options ............................................ 26
IBM 46XX Parameter - Inter Record Delay ......................... 26
Light Pen Options ............................................. 27
Light Pen Emulation ........................................... 28
Code Type Selections ....................................... 28-30
Minimum Code Length for All Code Types ......................... 31
Code Length Minimum Feature ................................... 31
UPC/EAN Code ............................................... 32
UPC-A Options ............................................... 32
UPC-E Options ............................................ 33, 34
UCC Supplemental Options ..................................... 34
Supplemental ISBN Options ..................................... 35
Coupon Code 128 .......................................... 35, 36
Code 39 .................................................. 36, 37
Codabar ..................................................... 37
Interleaved 2 of 5 (ITF) ......................................... 38
Interleaved 2 of 5 (ITF) Symbol Lengths ........................ 39-41
ITF Minimum Symbol Length Test ................................ 42
MSI Plessey Check Digit ..................................... 42, 43
UK Plessey Options ............................................ 43
ScanPal Data Collector ......................................... 44
Test Modes ................................................... 44
Special Features ............................................ 45-47
User Programmable Prefix and Suffix ID Characters .................. 48
RB0 - RB9 Bar Codes .......................................... 49
ASCII Reference Table ...................................... 50-54
PC Extended Reference Key Tables ............................ 55, 56
Reserved Codes ............................................ 57-68
Disclaimer ................................................... 69
Index .................................................... 70-72
1
Scope of the MS951 Programming Guide
This Manual contains all of the configuration codes for all versions of the
MS951 hand-held bar code scanner products.
Not all hardware versions of the scanner support all of the features universally.
PC Keyboard Wedge units do not use baud rates. Light Pen emulation
scanners should not try to drop UPC/EAN check digits. Some features will
deliver different results based upon the primary interface selected.
Emphasis will be placed on PC Keyboard Wedge and RS-232 applications.
Keyboard Wedge units default to Keyboard Wedge communications. All other
units default to RS-232 parameters.
* *
2
Programming the Scanner
The scanner is shipped from the factory programmed to a set of default
conditions noted in this guide by an asterisk that appears before the brief
definition. Since each host system is unique, the scanner has to be configured
to match your host system requirements.
1. Connect the scanner to the host system or power source.
(Refer to the Installation and User’s Guide MLPN 2365.)
2. Scan the ENTER/EXIT PROGRAM MODE bar code.
(The unit will beep three times.)
Enter/Exit
Program Mode
3. Scan by positioning the output window within two inches of each code.
(When the first menu selection has been scanned, the laser will stay on
until the ENTER/EXIT PROGRAM MODE code is scanned again. If
no scanning occurs for 30 seconds while the scanner is in program
mode, the unit will beep three times and all changes made will be lost.
If this occurs, return to Step 1.)
4. Upon completing the scanning of the appropriate configuration options,
scan the ENTER/EXIT PROGRAM MODE bar code again. (The new
options will be saved and the scanner is ready for normal operation.)
Note: While in program mode, the scanner will make a “razz” sound when:
!the bar code it is scanning is not a program mode
code type;
!the feature is not currently supported in the firmware;
!the feature is not supported on the scanner’s hardware
configuration.
The sound serves as an audible indication that the scanner will not
support that feature.
DF1
R1 8
R1 9
DF1
Recall Defaults
3
Enter Program Mode
**Ability to Enter Program When this option is selected, pro-
Mode After Any Scan gramming can be entered by scann-ing
the ENTER/EXIT PROGRAM MODE
bar code after power up or during
normal scanning operation.
Enter Program Mode When this option is selected, the
Only on First Scan scanner will only enter program
mode after power-up. Scan the
ENTER/ EXIT PROGRAM MODE
bar code immediately after the scan-
ner first receives power. This option
prevents the scanner from accident-
ally entering program mode during
normal scanning operation.
Recall Defaults
If during programming of the scanner,
there is a need to return to the original Recall Defaults
factory settings, scan the RECALL
DEFAULTS bar code. Any settings
selected during that session or a
previous session will be lost.
* *
RS1
RS3
RS2
RS4
RS5
RS6
LP8
Enter/Exit Program Mode
4
Laser Activation Range
Short Range Activation When this option is selected, the IR sensor
Out of the Stand is guaranteed to be activated when the posi-
tion of the scanning window three inches from
the object.
Short Range Activation When this option is selected, the IR sensor
In the Stand is guaranteed to be activated when an object is
presented three inches from the scanning
window.
**Long Range Activation When this option is selected, the IR sensor
Out of the Stand is guaranteed to be activated when the posi-
tion of the scanning window is eight inches
from the object.
**Long Range Activation When this option is selected, the IR sensor
In the Stand is guaranteed to be activated when an object is
presented eight inches from the scanning
window.
Laser Operation
** Normal Scan This option is the default setting. When the laser is
activated by the IR sensor, the laser beam emits from the
output window and displays a constant, horizontal line
until a bar code is sensed or until the scanner timeout
elapses.
Pulsing Scan When the laser is activated by the IR sensor, the laser
beam emits from the output window and displays a
horizontal line that pulses until a bar code is sensed or
until the scanner timeout elapses.
Custom Scan This option is available for special applications.
Do not scan the CUSTOM SCAN bar code unless
instructed by a Metrologic representative.
DF1
R3 0
R3 1
E X 6
E X 5
R9 2
R9 3
Recall Defaults
5
Same Symbol Re-Scan
The scanner is programmed with a same symbol timeout.
For SHORT SAME SYMBOL RE-SCAN, the time delay Short Same
is ½ second, while the LONG SAME SYMBOL RE- Symbol Re-Scan
SCAN delay is 1 second. These numbers represent how
much time that a bar
code must be out of the scan field before that bar code can
be scanned again. ** Long Same
Symbol Re-Scan
Identical Symbol Re-Scan Indicator
During the same symbol timeout, the LED’s do not ** Disable Green LED
provide an indication of when the unit is ready to
begin scanning the same symbol again. To program
a LED to flash when thepreset delay is over, configure
the scanner to Green LED Enabled. Enable Green LED
1 vs 2 Scan Buffers
This feature controls the number of bar codes Enable 2 Scan Buffers
considered for the purposes of the same symbol
re-scan. The default, 1 scan buffer only compares
new scanned data against the last bar code scanned.
2 scan buffers allow the scanner to test the last
2 bar codes scanned for same symbol re-scan **Enable 1 Scan Buffer
purposes.
Autres manuels pour MS951
2
Table des matières
Autres manuels Metrologic Scanner
Metrologic
Metrologic MS9500 Voyager Series Manuel utilisateur
Metrologic
Metrologic MK9535-39B538 Manuel utilisateur
Metrologic
Metrologic Laser Scanner Manuel utilisateur
Metrologic
Metrologic MS951 Manuel utilisateur
Metrologic
Metrologic MS9540-38-3 - Metrologic MS9540 VoyagerCG Manuel utilisateur
Metrologic
Metrologic OrbitCG MS7180 Manuel utilisateur
Metrologic
Metrologic MS9524 VoyagerPDF Series Manuel utilisateur
Metrologic
Metrologic ARGUSSCAN MS7220 Manuel utilisateur
Metrologic
Metrologic Eclipse MS5145-00 Manuel utilisateur
Metrologic
Metrologic iQ160 Guide de l'utilisateur
Metrologic
Metrologic IS8000 Manuel utilisateur
Metrologic
Metrologic IS4220 ScanGlove Instructions d'installation et d'utilisation
Metrologic
Metrologic MS9535 VoyagerBTSeries Manuel utilisateur
Metrologic
Metrologic FocusBT MS9535 Manuel utilisateur
Metrologic
Metrologic MS6720 Instructions d'utilisation
Metrologic
Metrologic Orbit MS7120-38 Manuel utilisateur
Metrologic
Metrologic MK9535-39B538 Manuel utilisateur
Metrologic
Metrologic MK2320KD-60B241 - Metrologic MS 2320 Stratos... Manuel utilisateur
Metrologic
Metrologic IS4320 ScanGlove Mode d'emploi
Metrologic
Metrologic IS4225 ScanGlove Manuel utilisateur
