Metra Electronics 99-3030B Manuel utilisateur
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 2/21/19 INST99-3030B
INSTALLATION INSTRUCTIONS
99-3030B
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Complete center dash panel for a factory look
• Painted matte black
• Includes an Axxess interface, wiring harness, ASWC-1,
and antenna adapter for a complete installation
KIT COMPONENTS
• A) Radio/climate control panel • B) Radio brackets • C) Climate control trim panel A (04-05) • D) Climate control trim panel B (06-09) • E) Pocket
• F) (6) Panel clips • G) (12) #8 x 3/8” Phillips screws • H) Axxess interface and wiring harness (not shown) • I) Antenna adapter (not shown)
• J) ASWC-1 (not shown) TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32” Socket wrench
TABLE OF CONTENTS
Dash Disassembly ...............................................2-3
Kit Preparation ...................................................4-5
Kit Assembly
–ISO DIN radio provision with pocket ..................6
–ISO DDIN radio provision .....................................7
Axxess Interface Installation .................................8
Final Assembly ...................................................... 11
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Axxess interface included
Antenna Adapter: Included with kit
Steering wheel control interface: ASWC-1 included
A B C
GF
D E
Cadillac XLR 2004-2009
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
1.800.221.0932
|
MetraOnline.com
2
1. On the bottom of the shifter, pull the
chrome trim downward, and then
remove (1) screw exposed. Pull up on
the shifter to remove it. (Figure A)
2. Unclip the shifter trim plate, then set to
the side. (Figure B)
Continued on the next page
DASH DISASSEMBLY
(Figure B)(Figure A)
REV. 2/21/2019 INST99-3030B 3
DASH DISASSEMBLY (CONT.)
(Figure A)
3. Unclip, unplug, and remove the radio/
climate control panel. (Figure C)
4. Remove (4) 9/32” screws securing the
radio. Slide the radio out, then unplug
and remove the radio. (Figure D)
Continue to Kit Preparation
(Figure D)(Figure C)
1.800.221.0932
|
MetraOnline.com
4
KIT PREPARATION
From the factory radio/climate control panel:
1. Unclip and remove the a/c vents.
(Figure A)
2. Unclip and remove the hazard switch.
(Figure A)
3. Remove (4) screws securing the climate
controls, then remove the controls.
(Figure A)
Continued on the next page
(Figure A)
REV. 2/21/2019 INST99-3030B 5
KIT PREPARATION (CONT.)
4. Secure the appropriate
climate control
trim panel
to the
99-3030B radio/
climate control panel
using the (4)
#8 x 3/8” Phillips screws provided. The
climate control panel
part number is
stamped onto the back of the panel.
CH-3030-1 - 2004-2005
CH-3030-2 - 2006-2009 (Figure A)
To the 99-3030B radio/climate control panel:
5. Secure the (6) panel clips supplied to the
panel (the factory clips can also be used
if so desired). (Figure B)
6. Clip in the factory a/c vents. (Figure C)
7. Clip in the hazard switch. (Figure C)
8. Secure the climate controls to the panel
using the (4) #8 x 3/8” Phillips screws
provided. (Figure C)
Continue to Kit Assembly
(Figure A) (Figure B) (Figure C)
1.800.221.0932
|
MetraOnline.com
6
KIT ASSEMBLY
ISO DIN radio provision with pocket
1. Secure the
radio brackets
to the
pocket
using the (4) #8 x 3/8” Phillips screws
provided. (Figure A)
2. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket
assembly, then secure it to the assembly
using the screws supplied with the
radio. (Figure B)
Continue to Axxess Interface Installation
(Figure A) (Figure B)
REV. 2/21/2019 INST99-3030B 7
(Figure A)
ISO DDIN radio provision
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
Continue to Axxess Interface Installation
KIT ASSEMBLY
1.800.221.0932
|
MetraOnline.com
8
AXXESS INTERFACE INSTALLATION
INTERFACE FEATURES
INTERFACE COMPONENTS
• Axxess interface
• 3030 harness
• 16-pin harness with stripped leads
• ASWC-1 harness
• ASWC-1 interface
• CD player jumper harness
• Female 3.5mm connector with stripped leads
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun, solder, and heat shrink
• Small flat blade screwdriver • Tape • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections ...............................................................................................................................9-12
Installation ...................................................................................................................................13
Programming ...............................................................................................................................13
Adjustments .................................................................................................................................14
• Provides accessory power (12-volt 10-amp)
• Maintains the Retained Accessory Power (R.A.P.) feature
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains warning chimes
• Retains OnStar/OE Bluetooth
• Adjustable volume for chimes and OnStar
• Retains steering wheel controls via ASWC-1
• Retains the factory amplifier
• Retains balance and fade
• Micro-B USB updatable
REV. 2/21/2019 INST99-3030B 9
From the 3030 harness to the aftermarket radio:
• Connect the Black wire, and the (3) Black/White wires to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Blue wire to the power antenna wire.
• If the aftermarket radio has an illumination wire, connect the Orange wire to it.
• The Black/Yellow wire is used for OnStar level adjustment for models that do not come
equipped with steering wheel controls. Refer to the Onstar level adjustment section for
futher instructions.
ASWC-1 harness:
This harness is to be used along with the ASWC-1 to retain steering wheel audio controls. Refer
to the ASWC-1 vehicle specific install instructions available at axxessinterfaces.com for radio
connections and programming.
• Connect the Red wire to accessory power.
Continue to Installation
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connect the Red wire to the accessory wire.
Note: There will be a Red wire from the 3030 harness to connect as well.
• Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear
sound from the factory amplifier.
• If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is
not connected, the radio will turn off when OnStar is activated.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative speaker output.
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
• Connect the Light Green wire to the parking brake wire.
• Tape off and disregard the Orange/White wire, it will not be used in this application.
CONNECTIONS
1.800.221.0932
|
MetraOnline.com
10
I N S TAL L ATI O N
With the key in the off position:
1. Connect the CD player jumper harness to the wiring harness in the vehicle.
2. Connect the ASWC-1 harness to the wiring harness in the vehicle. Do not connect the ASWC-1
until the Axxess interface is programmed and fully functional.
3. Connect the 16-pin harness with stripped leads into the Axxess interface.
4. Connect the 3030 harness into the Axxess interface, and then to the wiring harness in the
vehicle.
5. Locate the factory antenna connector in the dash and complete all necessary connections to
the radio. Use the antenna adapter provided to adapt the factory antenna connector to the
aftermarket radio.
PROGRAMMING
Attention! If the interface ever loses power, the following steps will need to be performed again.
Please ensure that the owner of the vehicle knows this.
1. Temporarily connect the climate control while programming.
2.
Turn the key to the ignition position and wait until the radio comes on
.
Note: If the radio doesn’t come on within 60 seconds, turn the key to the off position,
disconnect the interface, check all connections, reconnect the interface and then try agin.
3.
Cycle the key off. If the driver’s door is closed, open and close the door. Cycle the key back on.
4. Test all funtions of the installation for proper operation, before reassemblying the dash.
5. Connect the ASWC-1 to the ASWC-1 harness, then program it per the vehicle specific install
instructions.
Table des matières
Autres manuels Metra Electronics Accessoires automobiles
Metra Electronics
Metra Electronics 99-3100 Manuel utilisateur
Metra Electronics
Metra Electronics 99-7477 Manuel utilisateur
Metra Electronics
Metra Electronics 99-5834CH Manuel utilisateur
Metra Electronics
Metra Electronics 95-5703B Manuel utilisateur
Metra Electronics
Metra Electronics 99-3012G Manuel utilisateur
Metra Electronics
Metra Electronics 99-7878B Manuel utilisateur
Metra Electronics
Metra Electronics 99-3023HG Manuel utilisateur
Metra Electronics
Metra Electronics 95-8904B Manuel utilisateur
Metra Electronics
Metra Electronics 95-7810B Manuel utilisateur
Metra Electronics
Metra Electronics CADILLAC 95-2004 Manuel utilisateur
Metra Electronics
Metra Electronics 99-4700 Manuel utilisateur
Metra Electronics
Metra Electronics 99-7819 Manuel utilisateur
Metra Electronics
Metra Electronics 99-7863 Manuel utilisateur
Metra Electronics
Metra Electronics 95-7326 Manuel utilisateur
Metra Electronics
Metra Electronics 99-7509 Manuel utilisateur
Metra Electronics
Metra Electronics MPS-GEN01 Manuel utilisateur
Metra Electronics
Metra Electronics 99-7414 Manuel utilisateur
Metra Electronics
Metra Electronics 99-9401 Manuel utilisateur
Metra Electronics
Metra Electronics HONDA RIDGELINE 99-7870G Manuel utilisateur
Metra Electronics
Metra Electronics 98-7499 Manuel utilisateur
