Metel 2G-2.1.4.E-BOX-PoE++ Manuel utilisateur

www.metel.eu 1/10

LAN-RING System PoE++ Managed Switches

2G(200M)-2.1.4.E PoE++

OBJEDNACÍ NÁZEV KÓD NAPÁJENÍ

2G-2.1.4.E-BOX-PoE++ 1-859-226 10-60VDC/10-30VAC**

200M-2.1.4.E-BOX-PoE++ 1-759-226 10-60VDC/10-30VAC**

LAN-RING 2Gbps

RS485

6x IO

RS485

2G-2.1.4.E++ 2G-2.1.4.E++

2G-2.1.4.E++

2G-2.1.4.E++ 2G-2.1.4.E++

2G-2.1.4.E++

EXP-C EXP-C

EXP-C

2G-0.1.4.E

2G-0.1.8.E

2G-2.0.1.E

RS485

** supply with PoE+ 53-57VDC, without PoE 10-60VDC/10-30VAC

1x MM or SM fiber

Fast Ethernet

LEGEND

others

Gigabit Ethernet

** supply with PoE 48-56VDC, without PoE 10-60VDC/10-30VAC

* holder DIN35-LOCK for mounting to DIN35 included

▪Ring topology LAN-RING

▪Overvoltage protection 1kA on FE ports

▪1x RS485 port with support of:

APOLLO, ASSET, ATS, CIAS, DOMINUS, GALAXY,

HUB-PRO, PERIDECT, ROGER, SATEL-ACCO,

SICURIT-ABSOLUTE, STATION-ONE, Modbus

▪2x digital input

▪1x programmable relay

▪2x MM/SM universal optical ports with WDM

▪1x Gigabit Ethernet

▪3x Fast Ethernet port with PoE support (15.4W)

▪1x Fast Ethernet port with PoE++ support (90W)

▪2 supply inputs

▪IP Watchdog

▪SNMP, SMTP, SNTP, IGMP, UPNP support

▪Support VLAN, 802.1p/q, QoS

▪ Support of logging to SD card

▪Working temperature from –40°C to +70°C

BOX* BOX + DIN35-LOCK*

www.metel.eu 2/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

Ring topology LAN-RING

LAN-RING is suitable especially for extensive alarm and automation systems. The core of the system are industrial switches

supporting ring topology with fast reconfiguration in 30ms. The swithes are apart from Ethernet port (optics / twisted pair)

equipped with other ports such as RS485, RS422, RS232, digital inputs, relays outputs, TTL inputs/outputs and audio inputs/

outputs (see the table). That enables interconnection of multiple systems (IP CCTV, automation, LAN, ESS, PIDS etc.) using one

optical fiber.

* it is not possible to use both interfaces at the same time

5-year ALL INCLUSIVE warranty

For all LAN-RING system devices we provide 5-year ALL INCLUSIVE warranty including damage caused by excessive voltage (for

detailed specification see “Warranty ALL INCLUSIVE” on our webpages www.metel.eu).

Overvoltage protection 1kA on FE ports

Overvoltage protections of LAN-RING switches guarantee reliable operation even

in outdoor installations. The optimum placement of the switch, devices and cables

connected to the switch is in protection area

of a lightning rod, i.e. ZBO0B zone acc. to IEC 62305-4.

The switches ports are protected in two ways:

- two-level class D protection consisting of lightning

arresters, separating impedances and transils

- fine class D protection consisting of transils

* When connecting switches in outdoor environment we recommend

having all ports with supply feed longer than 10m protected by protections: .

RS485 RS422 RS232 Relays Dig. Inputs TTL IN/OUT Audio IN/OUT

2G-6S.1.16.E 1 - - 1 2 - -

2G-2.1.7.E 1 - - 1 2 - -

2G(200M)-2.1.4.E 1 - - 1 2 - -

2G(200M)-2.0.4.ECA(B) 1 1(A) - 1 2(B) - -

2G-2.3.0.E 1 - - 2 2 - -

2G(200M)-2.0.1.E 1 - - 1 2 - -

200M-EVA(8).E - - - 1 - 2/2 (8/8) 2/2

2G-0.1.8.E - - - - - -

2G(200M)-RS.E RS485* - RS232* 1 (max. 60V/1(0.4)A) 2 -

Backup

segment

Failure

Backup

segment

230VAC

Supply line in ZBOB zone up to 10m over 10m

Fast ethernet ports no no

Gigabit ethernet ports no yes

Supply inputs no yes*

RS485/422/232 ports no yes

Digital inputs no yes

Relay outputs no yes

* we recommend using outdoor supply SU-230/4870H

Switch grounding

SU-230/4870HOVP

OVP –fast ethernet

OVP

Is it necessary to instal additonal overvoltage protections? Lightning rod

Switch and camera in

protection areaof the

lightning rod

ZBO0B

ZBO0A

www.metel.eu 3/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

1x RS485 port

The switches are equipped with one RS485 port. This port can be set in three basic modes:

TCP server/client –for direct interconnection with the application on control server,

UPD mode –for interconnection of 2 or more devices with the request of extremely low latency. Typical latency is 3-4ms on

bitrate 9.6kbps.

IO(EXP-C) mode –for connection of up to 15 I/O units EXP-C (6 digital inputs/outputs), temperature sensors, etc.

2x digital input

The switches are equipped with two digital inputs compatible with balanced

loops of all alarm systems. The input state can be:

- Sent via SNMP protocol to integration software (e.g. C4)

- Remapped to relay of other switches or I/O modules.

Everything is adjustable locally via USB or remotely over LAN software SIMULand.

1x programmable relay

The switches are equipped with a programmable relay output which could be activated by e.g.:

- Connection failure over LAN or RS485, interruption of optical ring, etc.

- Opening (closing) of one or more inputs on other switches and I/O modules

- Function IP watchdog that automatically restarts "frozen" devices

- SNMP protocol from integration software (e.g. C4)

Everything is adjustable locally via USB or remotely over LAN software SIMULand.

2x MM / SM universal optical ports with WDM

All optical ports on 2G(200M)-...E series devices can be universally used for both MM and SM fibers in the range of 8/125μm to

62.5/125μm. Optical ports are equipped with integrated wavelength division multiplexer technology (WDM). The optical

ring/connection is then made up of only one SM or MM fiber.

RS485 RS485

RS485

TCP

switch

RS485 RS485

RS485

UDP

switch

RS485

EXP-C

switch

EXP-C

switch

RS485

EXP-C

polytron 10k

10k

+3.3V

polytron

IN1

IN2

GND

Optical power 2G/200M: –9...–3/–14...–8 dBm 9/125µm

Sensitivity 2G/200M: –22/28 dBm 9/125µm

Optic fibers 1x SM 8(9)/125 - SC connectors µm max. 20 km between components

1x MM 50(62,5)/125 - SC conn. µm 2G/200M: max. 2/5 km between components

Wavelengths PORT 6: Tx: 1310 / Rx: 1490(1550) nm (200M)

PORT 7: Tx: 1490(1550) / Rx: 1310 nm (200M)

Safety WARNING: converters contain laser sources of class 1 according to EN 60825-1-1

Parameter Value Unit Note

www.metel.eu 4/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

LAN (UTP) Supported formats FE UTP ports: 10BaseT, 100BaseTx

GE UTP ports: 10BaseT, 100BaseTx, 1000BaseTx

Overvoltage protection FE ports: 1000 A 8/20us

GE ports: 30 A 8/20us

Connectors RJ45

Relay output Max. load 62,5VA (30W) / 1A / 60V resistive load

With PoE 48-57 VDC

With PoE++ 53-57 VDC

Power consumption Max. 5 W

Protections Overvoltage / current 100A (8/20µs)

Environment Operational range –40...+70 °C temp. of environment

Storage range –40…+85 °C

Humidity max. 95% non-condensing

Management Local / remote USB / application SIMULand / Win XP. 7 32 and 64bit

Power supply Without PoE 10-60 / 10-30 VDC/AC

Certification TÜV

The producer retains the right to change any technical parameters without previous announcement.

Parameter Value Unit Note

1x Gigabit Ethernet port

The port support standards 10BASE-T, 100BASE-TX, 1000BASE-T incl. functions: Auto-negotiation, Auto MDI/MDI-X, Power-down.

3x Fast Ethernet port with PoE+ (15,4W) support

The port support standards 10BASE-T, 100BASE-TX incl. functions: Auto-negotiation, Auto MDI/MDI-X and Power-down. The

ports also support supplying of terminal devices over Cat-5e cable acc. to IEEE 802.3-af / IEEE 802.3at (max. 15,4W per port).

1x Fast Ethernet port with PoE+ (90W) support

The port support standards 10BASE-T, 100BASE-TX incl. functions: Auto-negotiation, Auto MDI/MDI-X and Power-down. The

ports also support supplying of terminal devices over Cat-5e cable acc. to IEEE 802.3-at / IEEE 802.3at (max. 90W).

2x supply input

The switches are equipped with 2 independent supply inputs.

IP Watchdog

The switches are equipped with integrated IP Watchdog on FE ports. In case of failure they can reset PoE supply, activate relay

output or send a SNMP trap.

Support of SNMP, SMTP, SNTP, IGMP, UPNP

SNMP Protocol for data acquisition and control via LAN.

SMTP Protocol for sending e-mails.

SNTP Protocol for centralized time synchronization.

IGMP Protocol for the management of multicast groups.

UPNP The protocol for the detection of devices connected to the LAN (switches only support the transfer UPNP).

Support of VLAN, 802.1p/q, QoS

The switches support setting of VLAN, priorities and band width independently on all Ethernet ports.

Support of logging to SD card

The switches support logging of important operating data to a SD card.

Technical parameters

www.metel.eu 5/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

Installation and Setting

1. Mounting

Modification BOX –flat surface or DIN35

2. Connect supply

10-60VDC or 10-30VAC between terminals acc. to the

picture below. The supply is indicated by yellow LED PWR.

Overvoltage protections are grounded via GND terminal.

Connect GND terminal with ground using a cable of min.

1.5mm2 diameter.

3. Connect optic fibers

terminated by SC connector (grinding PC). Optical output

is indicated by green LED of a given port. Blinking

indicates data.

It is necessary to connect optical ports cross-wise,

i.e. port P6 to port P7 etc.

Note: Before closing the optical ring one switch

must be configured as Master (menu "Ring").

4. Connect signal wires

RS485 –connect bus A+ and B-, A+ is positive In the idle

state.

USB - connector for connection of USB A-B cable for local

management over SIMULand application.

RELAY - in alarm state COM and N.O. are closed.

Alarm state is considered in the following situations:

supply failure, communication loss and optic fiber

interruption.

In non-alarm state COM and N.C. are closed.

IN, OUT -digital inputs are activated by closing to GND or

by TTL level (0-0.3V „log 0“ and 2.7V-5V „log 1“).

TTL outputs can be mapped in switch management.

Revision:201301Revision:201301 - Default

Main supply:

No PoE: 10...60VDC 10-30VAC

With PoE: 48...57VDC

With PoE+: 53...57VDC

Redundant supply

No PoE: 10...60VDC

With PoE: 48...57VDC

With PoE+: 53...57VDC

GND (PE)

~ ~

Fast configuration

1. Download and install

application SIMULand.

2. Run application SIMULand

3. From menu „Project/Find devices“ scan avalaible

devices and put it on desktop. (IP adress network card

must be config in the same IP range as the IP address of

the switch)

4. Move the mouse cursor on the device, click on the left

and then the right mouse button. Select the menu

"Configuration / Online configuration" and enter the

password.

5. Basic setting:

menu „IP“ - setting the IP address, subnet mask and

gateway

„Enable answer to ping“ - enable / disable switch to reply

to a ping.

„Enable network management“ - unchecking the items

you will be able to switch only connect via USB.

6. Before closing the optical ring must be in the menu

„Ring“ always one switch is set to „Master".

When use more optical ring you must set every optical

ring another „Ring ID“.

www.metel.eu 6/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

Activation PoE/PoE++ on Fast Ethernet ports

1. In menu „Ports“ select FE ports FE („P1 –P4“),

where you want to activate PoE supply.

2. Checking the „Enabled" to enable PoE power supply

on the port.

3. On one of the ports „P1 - P4" You can turn

PoE + + by checking the „Poe + + Enabled".

Note: Item „Ignore discovery“ - pernamently turn on

PoE power supply without detection and classification

of PoE end devices.

The setting consists of the following steps:

1. In menu „Bus/Mode“ set the system you are using. If not provided select “RS485”set „Speed“ and „Data bits“. If the system

is provided in the menu no further setting in menu „Bus“ is needed. The switch sets it automatically.

2. In menu „Ethernet“ set receiving and transmitting addresses in range 239.0.0.0 - 239.255.255.255 (multicast).

topology BUS –set the same receiving and transmitting address on all switches.

topology POINT-to-POINT –set the addresses “crosswise”:

Example: Device 1 receiving address - 239.192.168.2, transmitting address 1 - 239.192.168.3

Device 2 receiving address - 239.192.168.3, transmitting address 1 - 239.192.168.2

LAN-RING

Tx 239.192.168.1

Rx 239.192.168.1

Tx 239.192.168.1

Rx 239.192.168.1

Tx 239.192.168.1

Rx 239.192.168.1

Fast Ethernet

LEGEND

RS485

Gigabit

1x MM or SM fiber

Setting of RS485 transmission in UDP mode (multicast)

www.metel.eu 7/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

LAN-RING

IP: 10.0.1.25

Port: 10485

IP: 10.0.1.27

Port: 10485

IP: 10.0.1.26

Port: 10485

TCP Client

The setting consists of the following steps:

1. In menu „Bus/Mode“ set the system you are using. If not provided select “RS485”set „Speed“ and „Data bits“. If the system

is provided in the menu no further setting in menu „Bus“ is needed. The switch sets it automatically.

2. In menu „Ethernet/TCP Port“ set numbers of TCP ports that will be used by a TCP client to establish communication.

3. Configure the TCP client in a PC with installed application (e.g. integration software).

Setting of RS485 transmission in TCP mode

Fast Ethernet

LEGEND

RS485

Gigabit

1x MM or SM fibre

www.metel.eu 8/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

input 1 input 2 input 1 input 2

PoE+ managed switches 2G-2.1.4.E

2x FO 2Gbps ♦1x GE ♦4x FE ♦1x RS485/Modbus ♦2x digital input ♦1x relay

CD - connected fiber detection

ACT - activity detection

P7 - optical port 2Gbps LAN-RING

Tx - 1490nm / Rx - 1310nm

P6 - optical port 2Gbps LAN-RING

Tx - 1310nm / Rx - 1490nm

CD - connected fiber detection

ACT - activity detection

P5 - gigabit Ethernet

10/100/1000 BASE-T

overvoltage protection

30A (8/20us)

USB - local management

application SIMULand over USB A-B

cable

P/R - LED POWER / RING

RS485 - LED RS485 TX(R) / RX(G)

RS485

max. 57.6 kbps

overvoltage protection

30A (8/20us)

PoE indication

POx - PoE ON

FAx - PoE fault

P...P4 Ethernet

10/100 BASE-T PoE* ports

LED - DUPLEX/COLLISION

ACT - LED ACTIVITY

overvoltage protection

1000A (8/20us)

LAN-RING

PCPC

RS485

PoE+

! C L A S S 1 L A S E R P R O DU C T !

CD ACT

PO4

PO3

PO2

PO1

FA4

FA3

FA2

FA1

USB

IN 1

IN 2

RELAY

A+

GND

B-

P/R

PoE

RS 485

2G-2.1.4.E

RELAY OUT

62,5VA (30W) / 1A / 60V

(resistive load) current limiter

(polytron)

ORDERING NAME SUPPLY with PoE/PoE++ SUPPLY without PoE TAMPER

2G-2.1.4.E 2G-2.1.4.E

2G-2.1.4.E

2G-2.1.4.E-BOX-PoE++ 48-57/53-57 VDC 48-57/53-57 VDC 10-60 VDC / 10-30 VAC 10-60VDC no

DIGITAL INPUTS

activation by closing to

GND or by TTL level

„log. 0“ 0V-0.8V

„log. 1“2V-5V

overvoltage protection

30A (8/20us)

*In application SIMULand can

select one port for PoE++

www.metel.eu 9/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

PoE+ managed switches 200M-2.1.4.E

2x FO 200Mbps ♦1x GE ♦4x FE ♦1x RS485/Modbus ♦2x digital input ♦1x relay

input 1 input 2 input 1 input 2

LAN-RING

PCPC

RS485

PoE+

ORDERING NAME SUPPLY with PoE/PoE+ SUPPLY without PoE TAMPER

200M-2.1.4.E 200M-2.1.4.E

200M-2.1.4.E

200M-2.1.4.E-BOX-PoE++ 48-57/53-57 VDC 48-57/53-57 VDC 10-60 VDC / 10-30 VAC 10-60VDC ne

CD - connected fiber detection

ACT - activity detection

P7 - optical port 200Mbps LAN-RING

Tx - 1490nm / Rx - 1310nm

P6 - optical port 200Mbps LAN-RING

Tx - 1310nm / Rx - 1490nm

CD - connected fiber detection

ACT - activity detection

P5 - gigabit Ethernet

10/100/1000 BASE-T

overvoltage protection

30A (8/20us)

USB - local management

application SIMULand over USB A-B

cable

P/R - LED POWER / RING

RS485 - LED RS485 TX(R) / RX(G)

RS485

max. 57.6 kbps

overvoltage protection

30A (8/20us)

PoE indication

POx - PoE ON

FAx - PoE fault

! C L A S S 1 L A S E R P R ODU C T !

CD ACT

PO4

PO3

PO2

PO1

FA4

FA3

FA2

FA1

USB

IN 1

IN 2

RELAY

A+

GND

B-

P/R

PoE

RS 485

200M-2.1.4.E

RELAY OUT

62,5VA (30W) / 1A / 60V (resistive

load) current limiter (polytron)

DIGITAL INPUTS

activation by closing to

GND or by TTL level

„log. 0“ 0V-0.8V

„log. 1“2V-5V

overvoltage protection

30A (8/20us)

P1 - P4 Fast Ethernet

10/100 BASE-T PoE* ports

LED - DUPLEX/COLLISION

ACT - LED ACTIVITY

overvoltage protection 1000A

(8/20us)

*In application SIMULand can

select one port for PoE++

www.metel.eu 10/10

Installation manual REV:201301

2G(200M)-2.1.4.E PoE++

LAN-RING System PoE++ Managed Switches

Size 2G a 200M-2.1.4.E PoE++

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Metel Changer

Metel

Metel 200M-RS.E4 Manuel utilisateur

Metel

Metel 2G 2S.0.3.F Instructions d'utilisation et d'entretien

Metel

Metel 200M-2.0.4.ECA Manuel utilisateur

Metel

Metel M-MDR-40-48 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur