Messoa NDR891(H) Manuel utilisateur
www.messoa.com
ZEIM-4000827G 2012-07 A1
Outdoor Dome Network Camera
NDR891(H)/NDR891E(H)
Quick Start Guide
Guia de inicio rápido
Guida rapida
Guide de démarrage rapide
Краткое руководство
クイックスタートガイド
快速安裝指南
快速安装指南
NDR891(H)/NDR891E(H) l Quick Start Guide 1
English
Safety Instructions
Make sure the supplied voltage meets the power consumption requirements
of the camera before powering the camera on. Incorrect voltage may cause
damage to the camera.
The camera should be protected from water and moisture, excessive heat,
direct sunlight and cold.
This installation should be made by a qualied service person and should
conform to all local codes.
Unplug the camera during lightening storms or when unused for long
periods of time.
Copyright
No part of this document may be reproduced or transmitted in any form or by
any means, electronic or mechanical, for any purpose, without the express written
permission of MESSOA.
© 2012 All rights reserved.
Disclaimer
Specications and information contained in this document are presented as
accurately as possible as of the time of release, but are not guaranteed to be
entirely free of error. MESSOA assumes no responsibility for errors or omissions
that may appear in this document and reserves the right to change this
publication at any time without obligation to notify anyone of such revisions or
changes.
2 NDR891(H)/NDR891E(H) l Quick Start Guide
1. Introduction
1.1 Package Contents
Outdoor Dome Network Camera x1
CD-ROM (User manual and IP Finder utility) x1
Quick Start Guide x1
Guide Pattern Sticker x1
RJ-45 Female / Female Coupler x1
Accessories
• Tapping Type Flat Head Screw (#1) x3
• Plastic Anchor(#2) x3
• Machine Type Flat Head Screw (#3) x3
NDR891(H)/NDR891E(H) l Quick Start Guide 3
English
1.2 Hardware Overview
Connectors
1
2
3
4
5
6
7
141mm (5.55”)
Ø108mm (4.25”)
121mm (4.76”)
1. Power In (Red+/Black-): Connect to DC 12V/AC 24V (NDR891/NDR891E) or
DC 24V/AC 24V (NDR891H/NDR891EH) power supply. If using the DC power
supply, make sure the power connector is wired to correct polarities (Red+/
Black–). If you are to use power via the PoE connection, this connector is not
used.
2. RJ-45 Ethernet Connector: Network & PoE (Power over Ethernet)
connection. Note that PoE is unable to drive the camera whose heater is
operating.
3. BNC: Composite video output
4. Audio Out (Green): Audio output
5. Audio In (Red): Audio input
6. Alarm Out (Orange): Alarm signal output port
Reserved (Green): Reserved contact
RS-485 (Yellow): Contact for RS-485
7. GND: Ground (electricity) in electrical circuits
Alarm In 1 (Red): Alarm signal input port
Alarm In 2 (Brown): Alarm signal input port
4 NDR891(H)/NDR891E(H) l Quick Start Guide
2. Installation
2.1 Mounting the Camera
This camera is designed for ceiling & wall mounts depending on your
requirements. Mount the camera to your intended location.
Disassembling
1. Take off the dome cover screws.
2. Rotate the dome cover counterclockwise to unlock and pull free of the
housing.
3. Then remove the inner liner by gently pulling it free of the two notches in the
housing.
1. Dome Cover Screws
2. Dome Cover
3. Inner Liner
Tip
Caution
Warning Note
For heater model, the dome cover should NOT be removed over 30 minutes
during installation. Otherwise, the desiccant may absorb too much moisture and
thus cause vapor when the heater is on.
NDR891(H)/NDR891E(H) l Quick Start Guide 5
English
Drilling the Mounting Surface
1. Post the “Guide Pattern” sticker on the mounting surface.
2. Aiming the circles (the gure below marked with “+“ ) on the sticker, drill
three screw holes and one cable entry hole in the ceiling/wall.
+
+
+
+
Mounting the Camera
Use the machine screws to secure the camera base to the surface (this gure take
the tapping type screws as the example to illustrate the mounting).
Guide Pattern Sticker
Tapping Type Screw
Plastic Anchor
Camera Base
TipCautionWarning
Note
1. While you are securing the camera with the accompanying screws, please be
advised to hold the camera by its base. Do not hold the lens or lens base with
force that may deform the lens.
2. Use the machine type screws if you are attaching the camera to a pendent
mounting. Use the tapping type screws for all other surfaces.
3. For cement surfaces, insert the “Plastic Anchors” into the holes. For softer
surfaces, do not use the “Plastic Anchors”.
6 NDR891(H)/NDR891E(H) l Quick Start Guide
Adjusting Camera Angle
Check the monitored view by wiring the RCA jack to a monitor. With an external
monitor connected, you can adjust the camera angle, zoom and focus for
appropriate or better view.
RCA Jack for
Composite Video Output
Pan Adjustment: Rotate the lens base to adjust the horizontal angle.
Tilt Adjustment: Tilt the lens base to adjust the vertical angle.
Tile Angle (max. 70 degrees)
Pan Angle (max. 355 degrees)
NDR891(H)/NDR891E(H) l Quick Start Guide 7
English
Horizontal rotation: Rotate the dome base to adjust the horizontal position. Do
not turn the base more than 355° as this may cause the internal cables to twist
and disconnect or break.
Horizontal Rotation
(max. 355 degrees)
TipCautionWarning
Note
When the tilt angle is less than 75 degrees, there is no distortion.
24° Wide Angle (9mm)
68° Tele Angle (3mm)
70° Tilt Angle
Distortion Area
8 NDR891(H)/NDR891E(H) l Quick Start Guide
Lens Adjustment: Loosen the screws to adjust the zoom control for desired
image view and adjust the focus for optimum picture sharpness. Re-tighten the
screws after nishing zoom/focus adjustments.
Tile (T) & Wide (W)
Near (N) & Far (∞)
Assembling the Camera
1. Assemble the inner liner.
2. If you are to use a microSD/SDHC card, remember to insert the card into the
slot before assembling the dome cover.
3. Assemble the dome cover.
4. Secure the dome cover with the accompanying screw.
Autres manuels pour NDR891(H)
1
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Messoa Caméra de sécurité
Messoa
Messoa PTZ900 Manuel utilisateur
Messoa
Messoa NIC990 Manuel utilisateur
Messoa
Messoa NCB855E Manuel utilisateur
Messoa
Messoa NCB750 Manuel utilisateur
Messoa
Messoa NCB355 Manuel utilisateur
Messoa
Messoa NDR891(H) Manuel utilisateur
Messoa
Messoa NIC990 Manuel utilisateur
Messoa
Messoa SDF418 Manuel utilisateur
Messoa
Messoa NCB855E Manuel utilisateur
Messoa
Messoa LPR610 Manuel utilisateur
Messoa
Messoa SCR367 Manuel utilisateur
Messoa
Messoa NDF820 Manuel utilisateur
Messoa
Messoa NDZ760 Manuel utilisateur
Messoa
Messoa NIC830-HN5 Manuel utilisateur
Messoa
Messoa NCB750 Manuel utilisateur
Messoa
Messoa NOD316 Manuel utilisateur
Messoa
Messoa SCR510HB-HN2 Manuel utilisateur
Messoa
Messoa NOD316 Manuel utilisateur
Messoa
Messoa SCR515PRO Manuel utilisateur
Messoa
Messoa NDR891PRO Manuel utilisateur
