Mercury SC1000 Manuel utilisateur
i
© 2006 Mercury Marine SC1000 System Tach/Speedometer and Smart Tow Tachometer
898283002 706
ii
TABLE OF CONTENTS
iii
Basic Operation and Features
Basic Operation and Features ....................................................1
Master Reset...............................................................................1
Auto Detection Engine Function..................................................2
Display Screens...........................................................................3
Warning System
Alarm Warnings...........................................................................4
Warning Display Screens............................................................5
Warning System with Descriptive Text
Alarm Warnings with Descriptive Text.........................................9
System Speedometer Display Screens
System Speedometer Display Screens.....................................11
System Tachometer Display Screens
System Tachometer Display Screens........................................ 13
Smart Tow Tachometer Display Screens
Cruise Control Operation...........................................................15
Launch Control Operation..........................................................17
Troll Control
Troll Control Operation..............................................................19
TABLE OF CONTENTS
iv
Speedometer Calibration
Speedometer Quick CAL Calibration.........................................22
Speedometer CAL 1 Calibration................................................22
Speedometer CAL 2 Calibration ...............................................24
Tachometer Calibration
Tachometer Quick CAL Calibration...........................................26
Tachometer CAL 1 Calibration..................................................26
Tachometer CAL 2 Calibration..................................................30
BASIC OPERATION AND FEATURES
1
Basic Operation and Features
22642
MODE
RPM x 1000
0
2
34
5
6
7
1
RESET
TROLL
+
TROLL
-
SPEED
0
20
30 40
50
60
70
10
RESET
TROLL
-MODE +
TROLL
SELECT
0
2
34
5
6
7
1
RESET
RPM x 1000
SMART TOW
Smart Tow
Tachometer
System Tachometer System
Speedometer
Power up: Each gauge will power up when the ignition is turned
on. The gauges will stay on as long as the ignition is on.
Lights: Adjusts the brightness and contrast of the gauge.
Buttons: The "MODE/SELECT" button is used for selecting
information screens. The "+" and "-" buttons are used for setting
engine speed during troll, cruise control, and setting gauge
calibrations.
Troll Control: Sets and controls the idle speed of the engine for
trolling without using the throttle. (System Tachometer and
Speedometer).
Cruise Control: Sets and controls the speed of the engine for
cruising. (Smart Tow Tachometer only).
Launch Control: Sets and controls the speed of acceleration from
idle to set cruise speed. (Smart Tow Tachometer only).
Engine Guardian System: Monitors the critical sensors on the
engine for any early indications of problems. The system will
respond to a problem by reducing engine speed and alert the
operator to a potentially damaging situation.
Warning System: The system sounds the warning horn and
displays the warning message.
Master Reset
Returns the gauge to the factory defaults through the Master Reset
command.
BASIC OPERATION AND FEATURES
2
IMPORTANT: Performing a master reset will reset the unit to the
factory defaults, thus eliminating any installation and calibrations
performed during set up of product.
Press the "-" and "+" buttons simultaneously for approximately 10
seconds (until the graphic bars collide) to restore the unit to factory
default settings. Press the "MODE/SELECT" button to confirm.
22660
MASTERRESET
MASTERRESET
ERASE CALIBRATION !
PRESS MODE/SELECT TO CONFIRM
Auto Detection Engine Function
The System Tachometer/Speedometer and Smart Tow
Tachometer come standard with an Engine Auto-detection feature.
This feature lets the gauge, on the initial power up, automatically
detect which engine type is used and configure the gauge to match
that engine type.
On first time power up of the gauge or after a Master Reset, the
gauge will display "AUTODETECT". Upon pressing the "MODE/
SELECT" button, the gauge will automatically determine engine
type. This will preset the data monitoring screens accordingly. The
intention is to make initial setup easier. Press the "MODE/
SELECT" button to start the Auto Detection Engine function.
AUTODETECT
ENGINE SMARTSCREEN
PRESS MODE/SELECT TO START
24298
If the gauge shows a warning of "NO STARBOARD ENGINE" or
"MULTIPLE STARBOARD ENGINES", the engine location must
be properly selected (Port and Starboard) at the engine using a
Mercury Computer Diagnostic System tool (CDS). Perform the
Master Reset and Auto Detect functions again. (Refer to Master
Reset).
BASIC OPERATION AND FEATURES
3
Computer Diagnostic System (CDS) Order through SPX
4520
Monitors all electrical systems for
proper function, diagnostics, and
calibration purposes. For
additional information, pricing, or
to order the Computer Diagnostic
System contact:
SPX Corporation
28635 Mound Rd.
Warren, MI 48092
or call:
USA - 1-800-345-2233
Canada - 800-345-2233
Europe - 49 6182 959 149
Australia - (03) 9544-6222
Display Screens
Tachometer Display Screen Speedometer Display Screen
Engine Break-in Speed
Engine Temperature Fuel Used
Oil PSI Cog/Sog - If there is a GPS input
Oil Pressure Distance and fuel to Waypoint
Trim and Water Pressure Clock - Air/Sea Temp
Water Pressure Inst. and Avg. Fuel Economy
Battery Voltage and Engine Hours Trip Odometer
Fuel Flow and Fuel Used Fuel Tank Levels
% Fuel Remaining (Fuel Tank 1) Oil Tank Levels
RPM Fresh Water Levels
Depth Waste Water levels
Speed/Sea Temperature
Dual Engine
Trim and RPM Synchronizer
Fuel Range
Fuel Flow
Trip Odometer
Steering Angle
WARNING SYSTEM
4
Alarm Warnings
NOTE: Alarm warnings are displayed as shown when used with
engines prior to Gen I (2007).
3200RPM
AL
bc
22663
MODE
RPM x 1000
0
2
34
5
6
7
1
RESET
TROLL
+
TROLL
-MODE
SPEED
0
20
30 40
50
60
70
10
RESET
TROLL
+
TROLL
-
a
REDUCE
THROTTLE
a - Display screen
b - Engine Guardian System
c - Alarm signal
When a problem is detected, the name of the offending alarm
appears on the display.
If problem can cause immediate engine damage, the Engine
Guardian System will respond to the problem by limiting engine
power. Immediately reduce the throttle speed and refer to the
warning messages on the following pages. Refer to the Engine
Operation, Maintenance, and Warranty Manual for further
explanation of the problem and the correct action to take.
The alarm message will stay displayed until the "MODE" button is
pressed. If there are multiple alarms, these will cycle on the display
at five-second intervals.
If the "MODE" button is pressed to display a different screen, the
flashing alarm signal "AL" will appear in the upper right corner to
indicate there still is a problem.
WARNING SYSTEM
5
Warning Display Screens
When a problem is detected with the engine, the warning display
screens will alert the operator to the potential problem. Refer to the
Engine Operation, Maintenance, and Warranty Manual for
explanation of the problem and the correct action to take.
PROBLEM TACHOMETER DISPLAY SPEEDOMETER DISPLAY
BATTERY ×
ENGINE DATA BUS ×
FAULT- HORN ×
FAULT- IGNITION ×
FAULT- INJECTOR ×
FAULT- OIL PUMP ×
FAULT- SENSOR ×
FAULT- WATER
TEMP ×
LOW FUEL ×
LOW OIL ×
OIL TEMP ×
OIL PSI ×
OVERHEAT ×
OVER SPEED ×
PRESSURE ×
RESERVE OIL ×
WATER IN FUEL ×
MAP ×
MAT ×
TPS ×
WARNING SYSTEM
6
NOTE: Not all screens may apply to your engine type.
MODE
RPM x 1000
0
2
34
5
6
7
1
RESET
TROLL
+
TROLL
-
OVERHEAT
PRESSURE
OVERSPEED
WATER
FAULT
RESERVE
FAULT
FAULT
7500 RPM
IN FUEL
HORN
90% REMAINING
OIL PUMP
INJECTOR
22763
1
2
3
4
5
6
7
8
IMPORTANT: Refer to the Engine Operation, Maintenance, and
Warranty Manual for further explanation of the problem and the
correct action to take. Contact your dealer if the problem persists.
1. OVERHEAT: The engine has overheated.
2. PRESSURE: There is insufficient water pressure in the
cooling system.
3. OVERSPEED: Engine speed exceeded the maximum
allowable RPM.
4. WATER IN FUEL: Water in the water separating fuel filter
reached the full level.
5. FAULT - HORN: The warning horn is not functioning correctly.
6. RESERVE OIL LOW - 2-STROKE OUTBOARD ONLY: Oil
level is critically low in the engine mounted oil reservoir tank.
7. FAULT - OIL PUMP: The oil pump has stopped functioning
electrically. No lubricating oil is being supplied to the engine.
8. FAULT - INJECTOR: One or more of the fuel injectors have
stopped functioning electronically.
Autres manuels pour SC1000
2
Table des matières
Autres manuels Mercury Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur