Meitav-tec MTSC Manuel utilisateur

Touch Screen Thermostat

MTSC/SUPER/PPH

Owner’s manual and technician settings

-2-

-3-

Index

1. Owner’s Manual ………………………………………………..... 4

1.1 Quick Guide …………………………………………………. 4

1.2 Turning the unit ON or OFF ……………………………….. 5

1.3 Adjusting the set-point temperature………………………...5

1.4 Switching between Fan speeds……………………………..6

1.5 Timer for turning the thermostat off ………………………. 7

1.6 Economy mode indications E1 – E5 ….………………….. 8

1.7 Freeze protection ………………………...…………………. 9

2. Installation Instructions……..………………………………..... 10

3. Wiring Configuration and DIP Switches…….……………..... 13

4. Technician Settings …….……………………………………..... 20

5. MAC Address (MTSC Series only) ……………...…………..... 36

1. Owner’s manual

-4-

*Auto

speed

High Low

Press to switch between

fan speeds:

Med.

System ON

Set-point

adjustment

Temperature

scale

Ambient /

Set-point

temperature

display

Fan speeds

indication

Press to

turn

system

ON or OFF

*In Auto speed, the active

speed will appear

System OFF

1.1 Quick Guide

1.2 Turning the unit ON or OFF

Press the button to turn the unit ON – system mode and fan

speed symbols will appear on display.

Press again to turn the unit OFF – the symbols will disappear.

1.3 Adjusting the set-point temperature

While the thermostat is ON, press the or buttons – the

set-point temperature will flash.

Press again to adjust the set point.

Unit ONUnit OFF

-5-

1.4 Switching between fan speeds

Press the button to

switch between fan speeds:

Low

speed

Medium

speed

High

speed

Auto

speed

Note: When Auto speed Is

selected, the word “AUTO”

and the active fan speed

will appear on display

-6-

The selection of fan speeds may be disabled depending on system

configuration.

-8-

Economy mode can be activated by triggering a window contact,

door switch, key-tag or PIR sensor.

When Economy mode is active, the thermostat will either turn off or

use special economy set points for cooling and heating set by

technician.

Please refer to parameters P25 and P26 in the technician setting

section of this manual.

The following indications will appear on display:

-E1 – Economy mode triggered by window contact

-E2 – Economy mode triggered by PIR (occupancy sensor)

-E4 – Economy mode triggered by door switch or key-tag

-E5 – OFF state triggered by door switch or key-tag

-E6 – Valves OFF and Fan low triggered by door switch or key-tag

1.10 Economy mode indications E1 – E6

Temperature

Time

Normal work Freeze protection

Cut-in

Cut-out

The Freeze protection feature will not allow the room temperature to

drop below predefined cut-in temperature. Depending on which

configuration the system is operating under (with or without Heat pump)

this feature will force the system to operate in heat mode and activate

the fan.

This feature will take effect when the thermostat is either ON or OFF.

When the room temperature rises above the predefined cut-out

temperature, the thermostat will return to its previous state.

When freeze protection is activated, the display alternates between

“AL” and room temperature.

For selection of cut-in and cut-out temperatures, please refer to

technician settings parameters P36 and P37.

-9-

1.11 Freeze protection

2. Installation Instructions

-10-

The MTS/SUPER Thermostat designed for flush mounting in the room

to be controlled. It should be located where the occupant can easily

read the display and use the controls.

If the built in temperature sensor is being used to measure room

temperature, the panel should be placed where the temperature is

representative of the general room conditions, away from cold or warm

air draughts, radiant heat and direct sunlight.

The panel should not be installed on an outside wall.

- The standard installation height is 1.5 meter (5 feet) from the floor.

WARNING: Risk of Electric Shock and Property Damage.

Disconnect power supply before making electrical connections.

The installation is to be performed by a qualified electrician.

WARNING: The integrated circuits in the controller are

sensitive to static currents. Take suitable precautions.

2. Installation Instructions (cont’)

-11-

Installation procedure:

1. separate the front display from the back plastic cover by inserting a a

small flat screwdriver into each of the three slots as shown in the

picture and rotating it gently.

2. Remove the front display and keep it in a safe place.

3. Connect the wires as shown in the enclosed wiring diagram. All

terminals accept 1x0.5mm2/24 AWG.

4. If necessary, make changes to the DIP switches position as

explained in this manual.

5. Place the thermostat in the electrical box and tighten up the 2

screws Europe - Gewiss Box - GW 24 203 or similar

US - Carlon – B114R or similar or similar

6. Adapt the front frame-panel into its place, by pushing it towards the

wall.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels meitav-tec Thermostat

meitav-tec

meitav-tec ETN-24-SUPER-PROG Guide de sécurité

meitav-tec

meitav-tec ETN-24-SUPER-PROG Manuel utilisateur

meitav-tec

meitav-tec ETN24-P-3S-HU Manuel utilisateur

meitav-tec

meitav-tec FHV-H1-PR-IR Manuel utilisateur

meitav-tec

meitav-tec ETN24-P-3S-HU Manuel utilisateur

meitav-tec

meitav-tec ETN-24-HC11-3S-PROG Manuel utilisateur

meitav-tec

meitav-tec TAT-SUPER Manuel utilisateur

meitav-tec

meitav-tec MTS/SUPER/CO2 series Mode d’emploi

meitav-tec

meitav-tec ETN-24-PM-H-1S Guide de sécurité

meitav-tec

meitav-tec ETN24-SUPER-SH-F Manuel utilisateur

meitav-tec

meitav-tec MTSC/SUPER/HU Manuel utilisateur

meitav-tec

meitav-tec ETN24-P-FC-SUPER2 Guide de sécurité

meitav-tec

meitav-tec ETN24-PM-HP-SUPER-BL Manuel utilisateur

meitav-tec

meitav-tec FMH-220-FAN-COIL-SUPER 3 Manuel utilisateur

meitav-tec

meitav-tec FMT24-SUPER Manuel utilisateur

meitav-tec

meitav-tec ETN-12-P-3S Manuel utilisateur

meitav-tec

meitav-tec ETN-24-PD-1S Manuel utilisateur

meitav-tec

meitav-tec ETN-P Series Guide de sécurité

meitav-tec

meitav-tec ETN24-PMH-SUPER Manuel utilisateur

meitav-tec

meitav-tec MTSCV/SUPER/PROG/HU/PIR Manuel utilisateur

meitav-tec

meitav-tec ETNC-SUPER-PROG-HU-PIR Manuel utilisateur

meitav-tec

meitav-tec SUPER-SI Series Manuel

meitav-tec

meitav-tec FMH24-PD-1S-IR Manuel utilisateur

meitav-tec

meitav-tec ETN24 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur

meitav-tec MTSC Manuel utilisateur

Manuels Thermostat populaires d'autres marques