Me-Mover Speed Manuel utilisateur
1
ME-MOVER.COM
QUICKSTART
GUIDE
for assembly and initial ride
Me-Mover
Fitness
Speed
Designed in Copenhagen
0 - 25+ mph
0 - 35+ km/h
54.5 Lbs
23.2 kg
Foldable Front and rear
disc brakes
Ø 16”
Wheel
Variable
Transmission
S20200412
2ME-MOVER.COM
!Visit our website for more information:
https://me-mover.com
Watch the Me-Mover tutorials & tips:
Find videos on how to assemble, adjust and ride the Me-Mover.
https://youtu.be/Qexn10Gc1-4
3
ME-MOVER.COM
Congratulations on your Me-Mover Speed!
Thank you for your purchase! Here is a Quickstart Guide to get you started.
Safety notications
To highlight some of the most important safety concerns, this Quickstart Guide contains
safety warnings that are featured throughout this guide.
The following symbol WARNING! calls attention to a potential hazard that, if not
properly addressed or avoided, could cause serious injury or death, property
damage and/or void your warranty.
Me-Mover Speed is not a toy.
Children must only ride the Me-Mover Speed with adult supervision.
WARNING!
Always read the User Manual before use, as this Quickstart Guide is for your
convenience only. Please visit: https://me-mover.com
WARNING!
Any unapproved modication to the Me-Mover Speed can make it unsafe and
voids your warranty. A component that is not approved, or assembly that is not
correct can put high stress on your Me-Mover Speed or components. A frame,
fork, or component with modifications could decrease your control and cause you to
fall. Do not sand, drill, file, remove secondary retention devices, install incompatible
forks, or make other modifications. Do not remove, tighten or release any bolt(s)
connected to the structural frame, or connecting the frame to the transmissions.
Before you add an accessory to your Me-Mover FIT consult your dealer to confirm that
it is compatible and safe.
WARNING!
You must always obey your local road laws and regulations. Me-Mover is not
liable for any legal infringements. It is up to the individual rider to remain up to
date with the laws in their respective area.
4ME-MOVER.COM
Me-Mover Speed Content Box
This is how your Me-Mover Speed is packaged in the box.
All pictures shown are for illustration purpose only. Actual product may vary due to
product enhancements.
5
ME-MOVER.COM
Frame with transmissions
and wheels
Steering column
Handlebar
Waterbottle holder
(optional)
Rear-light adaptor
Quickstart Guide
6 mm long hex-key
5 mm long hex-key
4 mm long hex-key
3 mm short hex-key
Open end 10mm wrench
Open end 13mm wrench
Quickstart Guide
The Me-Mover Speed box contains the following pieces and sub-assemblies:
6ME-MOVER.COM
AN OVERVIEW OF YOUR ME-MOVER Speed
7
ME-MOVER.COM
WARNING!
Always ensure that the quick releases are securely tightened suciently. If they come
loose you must re-adjust the quick release to make it tighter. Never drive the
Me-Mover Speed without having tested that your quick releases are correctly
mounted and secured.
WARNING!
To close the clamp you must use a fair amount of force, otherwise it may be too
loose.
OPEN position CLOSED position
Adjustment
screw
Washers Screw
Clamp
NOTE: When in open position, the adjustment screw needs to be adjusted so that closing
the quick release requires some force to close the clamp. The narrow part of the spring
should point towards the wheel, as illustrated.
Springs
HOW TO: USE THE QUICK RELEASES
The Me-Mover Speed has two quick releases. It is extremely important that these
quick releases are tightened securely before you use your Me-Mover Speed.
Front wheel quick release: used to secure the front wheel to the front fork.
Steering column quick release: used to adjust the height of the steering column. It can
be adjusted to suit a child or an adult.
To ensure the tightness of a quick release you need to:
1. Hold the clamp OPEN while you rotate the nut in a clockwise direction.
2. Rotate the nut until you cannot close the clamp anymore.
Then release the nut slightly so you can JUST close the clamp.
3. To close the clamp push it rmly inwards.
Grease can help to
smoothen the open/close
procedure
8ME-MOVER.COM
STEP ONE: UNBOXING THE ME-MOVER
1. Open the top layer and remove the cardboard sheet.
2. Remove now the accessory bag and handlebar.
9
ME-MOVER.COM
3. Remove the foam layer and cardboard pieces that hole the Me-Mover Speed in
place.
4. Grab the black centre part and carefully pull it up into a vertical position. Carefully lift
the product out of the box.
NOTE: The component is heavy! We urge you to use a second person to lift the object out
of the box.
5. Carefully remove the front column away from the transmissions and remove it
out of the box. We recommend to place the items on the cardboard you removed in the
beginning. Beware: Please handle the items with care. Risk of damaging the paint.
10 ME-MOVER.COM
STEP TWO: HANDLEBAR AND FRONT
COLUMN ASSEMBLY
1. Mount the handlebars. Place the handlebar in the stem. Place the stem bracket in
the center and then insert the four M5 screws with the washers through the bracket into
the stem. Tighten the screws using the 4mm hex key to maximum 5Nm. Your handlebar
may already be preassembled.
STEP THREE: CONNECTING THE FRONT
AND REAR FRAME
1. Connecting the front column to the frame. Align hole A in the front column ange
with hole Bin the center block.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Me-Mover Vélo
