Me-Mover FIT 2.0 Manuel utilisateur
1
ME-MOVER.COM
QUICK GUIDE
for assembly and initial ride
Me-Mover
Fitness
FIT 2.0
Designed in Copenhagen
2
ME-MOVER.COM
!BEFORE YOU START PLEASE REGISTER AT:
www.me-mover.com/me-mover-t-registration/
3
ME-MOVER.COM
Congratulations on your Me-Mover FIT 2.0!
Thank you for your purchase! Here is a Quick Guide to get you started.
Complete the registration rst
Registration and proof of purchase will help to make a warranty claim and lets us
contact you with updates and improvements. Please visit the following link to register
your Me-Mover FIT 2.0 in a few simple steps!
https://me-mover.com/me-mover-t-registration/
Safety notications
To highlight some of the most important safety concerns, this Quick Guide contains
safety warnings that are featured throughout this guide.
The following symbol WARNING! calls attention to a potential hazard that, if not
properly addressed or avoided, could cause serious injury or death, property
damage and/or void your warranty.
Me-Mover FIT 2.0 is not a toy.
Children must only ride the Me-Mover FIT 2.0 with adult supervision.
WARNING!
Always read the User Manual before use, as this Quick Guide is for your convenience
only. Please visit: https://me-mover.com/user-manual-and-how-to-videos/
WARNING!
Any unapproved modication to the Me-Mover FIT 2.0 can make it unsafe and
voids your warranty. A component that is not approved, or assembly that is not
correct can put high stress on your Me-Mover FIT 2.0 or components. A frame,
fork, or component with modications could decrease your control and cause you to
fall. Do not sand, drill, le, remove secondary retention devices, install incompatible
forks, or make other modications. Before you add an accessory to your Me-Mover
FIT 2.0 consult your dealer to conrm that it is compatible and safe.
WARNING!
You must always obey your local road laws and regulations. Me-Mover Fitness is
not liable for any legal infringements. It is up to the individual rider to remain up
to date with the laws in their respective area.
4
ME-MOVER.COM
IN THE BOX
This is how your Me-Mover FIT 2.0 is packaged in the box.
The Me-Mover FIT 2.0 box contains the following pieces and sub-assemblies:
Steering column
Front wheel
Handlebars
Frame with transmissions
and wheels
Mudguard
Front wheel
quick release
3mm short hex key
4mm long hex key
5mm long hex key
6mm long hex key
10mm open-end
wrench
Water
bottle holder
(optional)
Foot straps
5
ME-MOVER.COM
AN OVERVIEW OF THE ME-MOVER FIT 2.0
Front wheel quick release1
Locking bolt
Pedal Foot strap
Steering column quick
release2
Front fork
Transmissions
Fixtures for
accessories
Front disc brake
Steering
column
Front wheel Foot strap screw
Rear disc
brake
Centre block
screw
Handlebars
Handlebar stem
Brake handles
Inner steerer
Bottle
holder (optional)
Safety pin
Rear wheel
Folding
Fixture
6
ME-MOVER.COM
HOW TO USE THE QUICK RELEASES
The Me-Mover FIT 2.0 has two quick releases. It is extremely important that these
quick releases are tightened securely before you use your Me-Mover FIT 2.0.
Front wheel quick release1 : used to secure the front wheel to the front fork.
Steering column quick release2: used to adjust the height of the steering column. It
can be adjusted to suit a child or an adult.
To ensure the tightness of a quick release you need to:
1. Hold the clamp OPEN while you rotate the nut in a clockwise direction.
2. Rotate the nut until you cannot close the clamp anymore.
Then release the nut slightly so you can JUST close the clamp.
3. To close the clamp push it rmly inwards.
WARNING!
Always ensure that the quick releases are securely tightened. If they come loose you
must re-adjust the quick release to make it tighter. Never drive the Me-Mover FIT
2.0 without having tested that your quick releases are correctly mounted and
secured.
WARNING!
To close the clamp you must use a fair amount of force, otherwise it may be too
loose.
OPEN position CLOSED position
adjustment
screw
washers screw
clamp
NOTE: When in open position, the adjustment screw needs to be adjusted so that closing
the quick release requires some force to close the clamp.
7
ME-MOVER.COM
TO ASSEMBLE YOUR ME-MOVER FIT 2.0, FOLLOW THESE
STEPS:
1. Place the cardboard box on the oor and use this as an underlay during
assembly.
2. Open the steering column quick release and pull out the inner steerer from the
steering column. Pull the inner steerer out by 10cm. Tighten the quick release clamp
again so the inner steerer does not slide back down. Use a 5mm Hex Key to take out the
end plug.
3. Mount the handlebar stem on the inner steerer and tighten the two screws using
a 4mm hex key. Re-insert the end plug. Do not overtighten these screws beyond
5Nm.
WARNING!
Do not tighten the screws with more than 5Nm. 5Nm corresponds to a 20cm long
wrench with a force of 2.5kg.
Handlebar stem
Inner steerer
End plug
Steering column
quick release OPEN Steering column
quick release CLOSED
Inner steerer
End plug
10 cm
NOTE: Lubricate the inner steerer with oil or grease.
8
ME-MOVER.COM
4. Fitting the brake cables. The cables should be threaded behind the bottle holder,
through the cable loop on the steering column, and then around the inner steerer below
the stem as shown below.
Cable loop
Bottle Holder
xtures
Stem
L
R
NOTE: The left brake cable loops under the stem from the left hand side. The right brake
cable loops under the stem from the right hand side. This ensures the cables are close to
the frame; not interfering with the riders knees whilst riding.
Inner Steerer
9
ME-MOVER.COM
5. Connect the brake cables to the brake handles. Pull the brake handle and insert the
end cap into the slot in the brake handle.
6. Align the lock nut and adjustment screw and slide the cable into the groove. If
necessary, pull the brake cable housing so more cable is exposed. Screw the lock nut and
adjustment screw tight.
NOTE: Please take note of which cable operates the front and the rear brake when doing
this step. There may be local laws regulating how your brakes need to function.
Brake
handle
Slot
End cap
Brake
cable End cap in the slot
Lock nut
Adjustment
screw
Groove
10
ME-MOVER.COM
WARNING!
Always ensure that the front wheel quick release is fastened securely! For detailed
instructions refer to “How To Use The Quick Releases” on page 6.
7. Mount the front wheel to the front fork. Ensure that the front fork is pointing
forward. Slide the front wheel into the front fork so that the brake disc is placed between
the brake pads in the caliper.
8. Fasten the front wheel to the front fork using the front wheel quick release.
Hold the clamp OPEN while you rotate the nut in a clockwise direction. Rotate the nut
until you cannot close the clamp anymore. At this point release the nut slightly so you can
JUST close the clamp.
disc break
Brake caliper
Front wheel
Hold the clamp in
OPEN position
Rotate the nut in
clockwise direction
Table des matières
Autres manuels Me-Mover Vélo
