Master cool 53100-C Manuel utilisateur

User Guide and Parts List

UV LEAK LOCATOR KITS

53312

53100-C

53518-UV

53515

2 3

DYE INJECTION INSTRUCTIONS

(1)

(2)

(3)

(4)

(1)

(2)

(3)

(4A)

Disposable

Cartridge Type

Injector (2 oz)

53223

Mini Disposable

Cartridge Type

Injector (1 oz)

53809

(1)

(2B)

Refillable

Cartridge Type

Injector (2 oz)

53123

PLEASE USE CAUTION!!

• When injecting dye into a pressurized system, ALWAYS

wear safety glasses and gloves!

• Never breathe refrigerant vapor!

• Never use the UV light without wearing the UV glasses!

• Lamp surfaces will get hot very quickly.

DO NOT TOUCH THE LENS!

A. PURGING AIR FROM THE HOSE ASSEMBLY

It is important to eliminate any air in the hose before injecting dye

into the A/C system. (This process is necessary only once for the

setup).

Purging Disposable Cartridge Type Injector

• Hold the cartridge (2) upward while unscrewing the cap. Snap

the hose assembly (3) onto the cartridge, and coupler (4) or

(4A) to the hose assembly.

• While holding the assembly upward, attach the handle (1) to

the bottom of the cartridge by turning it clockwise. Continue

turning while dye enters the hose and pushes the air up. Use

a pen to press the depressor of the coupler (4) to release the

air if necessary. Repeat this process as needed until dye

appears at the coupler’s end.

Purging Reﬁllable Cartridge Type Injector

• Hold the dye injector (upward while unscrewing the cap/hose

assembly (2B). Turn the handle of dye injector (1) counter

clockwise all the way before ﬁlling. Fill the injector with dye.

Replace cap/hose (2B), tightening securely and attach coupler

(4) to the hose assembly.

• While holding the assembly upward, start turning the handle

(1) clockwise. Continue turning as dye enters the hose and

pushes the air up. Use a pen to press the depressor of the

coupler (4) to release the air, if necessary. Repeat this

process as needed until dye appears at the coupler’s end.

B. INJECTION

1. Turn the A/C system and engine off!!

2. Connect injector to the low side service port of A/C system.

Hold body of injector. Use (I) starting line on handle end as a

guide. Turn handle clockwise to inject 1 application of dye.

(Approximately 1 to 1 1/4 turn(s) for Concentrated Dye)

2 3

Dye Application Chart

AUTOMOTIVE

1 Application per system

(for a system using up to 10 oz. [300 ml] of

lubricant)

HVAC

1 Application per system

(for a system using up to 7 lbs. [3.2 kg] of

refrigerant)

3. Disconnect injector from the system and clean any excess

dye left around the service port.

LEAK DETECTION USING A UV LAMP

A. Turn Engine and A/C system on.

B. Allow dye to circulate throughout system.

C. Connect UV lamp to power. (If using rechargeable UV Light,

make sure the battery is fully charged). SEE CHARGING

INSTRUCTIONS!!

D. WEAR PROTECTIVE GLASSES!!

E. Do not use lamp near ﬂammable materials, liquids or gases.

F. For 53012 and 53312 UV lights only: Never use lamp for more

than 3 minutes at a time. Allow lamp to cool between uses, 3

MINUTES ON, 5 MINUTES OFF. If used continuously, you may

damage glass lens.

G. Turn lamp on. Search for a bright green/yellow glow where the

system is leaking. Clean the area around leak after repair.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Master cool Instrument de mesure

Master cool

Master cool 52240 Manuel utilisateur

Master cool

Master cool R134a Manuel utilisateur

Master cool

Master cool 89660 Manuel utilisateur

Master cool

Master cool 52238 Manuel utilisateur

Master cool

Master cool R134a Manuel utilisateur

Master cool

Master cool 98061 Manuel utilisateur

Master cool

Master cool 52233 Manuel utilisateur

Master cool

Master cool 98063-BT Manuel utilisateur

Master cool

Master cool Intella Sense 55800 Manuel utilisateur

Master cool

Master cool ULTIMA ID PRO 69HVAC -PRO2 Manuel utilisateur

Master cool

Master cool 52236 Manuel utilisateur

Master cool

Master cool 98061 Manuel utilisateur

Master cool

Master cool Black Series Manuel utilisateur

Master cool

Master cool R1234yf Manuel utilisateur

Master cool

Master cool 52251 Manuel utilisateur

Master cool

Master cool 98063-BT Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur