Martin MAC Quantum Wash Guide de configuration

MAC Quantum Wash™

SAFETY AND INSTALLATION MANUAL

Dimensions

All measurements are given in millimeters

547

452

271

240

581

460

511

153

431

claim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use

of, inability to use or reliance on the information contained in this document. The Martin logo, the Martin name, the Harman name and

all other trademarks in this document pertaining to services or products by Martin Professional or its affiliates and subsidiaries are

trademarks owned or licensed by Martin Professional or its affiliates or subsidiaries.

P/N 35000276, Rev. B

Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

DMX data link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Service and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Tilt lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Servicing the head air filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the fixture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Applying power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Safety Information

The following symbols are used to identify important safety information on the product and in this document:

Warning! The MAC Quantum Wash™ contains components that are accessible and live at high

voltage while the fixture is connected to power. These components remain under tension for up to

30 minutes after power is disconnected. Only technicians who are authorized by Martin™ and who

have access to the Martin™ service documentation for the MAC Quantum Wash are permitted to

open the fixture.

Warning! Risk Group 2 product according to EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

The latest versions of this Safety and Installation Manual and the MAC Quantum Wash User Guide are

available for download from the MAC Quantum Wash Product Support page on the Martin™ website at

www.martin.com. Before you install, operate or service the MAC Quantum Wash, check the Martin™

website and make sure that you have the latest user documentation for the fixture. Document revisions are

indicated at the bottom of page 2. Follow the safety precautions and observe all warnings in this manual, in

the MAC Quantum Wash User Guide, and printed on the fixture.

This product is for professional use only. It is not for household use.

Respect all locally applicable laws, codes and regulations when installing, powering, operating or servicing

the fixture.

This product presents risks of severe injury or death due to fire and burn hazards, electric shock and falls.

If you have questions about how to operate the fixture safely, please contact your Martin™ supplier or call

the Martin™ 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180.

PROTECTION FROM ELECTRIC SHOCK

• Do not remove any cover from the fixture except as described under “Service and maintenance” on

page 12.

• Disconnect the fixture from AC power before servicing it and when it is not in use.

• Ensure that the fixture is electrically connected to ground (earth).

• Use only a source of AC power that complies with local building and electrical codes and has both

overload and ground-fault (earth-fault) protection.

• The power input cable must be rated 20 A, hard usage type and heat-resistant to 90° C (194° F)

minimum. It must have three conductors and an outer cable diameter of 5 - 15 mm (0.2 - 0.6 in.). In North

America the cable must be 12 AWG minimum conductor size, type SJT or equivalent. In the EU the cable

must be 2.5 mm² minimum conductor size, type H05VV-F or equivalent.

• Before using the fixture, check that all power distribution equipment and cables are in perfect condition

and rated for the current requirements of all connected devices.

WARNING!

Read the safety precautions in this section before

installing, powering, operating or servicing this

product.

DANGER!

Safety hazard.

Risk of severe

injury or death.

DANGER!

Hazardous

voltage. Risk of

lethal or severe

electric shock.

WARNING!

Fire hazard.

WARNING!

Burn hazard. Hot

surface. Do not

touch.

WARNING!

Intense light

emission.

WARNING!

Refer to user

manual.

Safety Information 5

• Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component

is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs

have been completed.

• Use only a Neutrik PowerCon NAC3FCA cable connector to connect to the power input socket.

• Do not expose the fixture to rain or moisture.

• Refer any service operation not described in this manual or in the MAC Quantum Wash User Guide to

Martin™ Service or an authorized Martin™ Service partner.

PROTECTION FROM BURNS AND FIRE

• The exterior of the fixture becomes hot. Take care when handling.

• Keep all combustible materials (e.g. fabric, wood, paper) at least 0.2 m (8 in.) away from the fixture.

• Keep flammable materials well away from the fixture.

• Ensure that there is free and unobstructed airflow around the fixture.

• Provide a minimum clearance of 0.2 m (8 in.) around fans and air vents.

• Do not illuminate surfaces within 2.0 m (6.6 ft.) of the fixture.

• Do not expose the front glass to sunlight or any other strong light source from any angle. Lenses can

focus the sun's rays inside the fixture, creating a potential fire hazard.

• Do not attempt to bypass thermostatic switches or fuses.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

• Do not modify the fixture in any way not described in this manual or the product’s User Guide or install

other than genuine Martin™ parts. Do not stick filters, masks or other materials onto any lens or other

optical component. Use only accessories approved by Martin™ to mask or modify the light beam.

PROTECTION FROM EYE INJURY

• Do not look at LEDs with magnifiers, telescopes, binoculars or similar optical instruments that may

concentrate the light output.

• Ensure that persons are not looking at the LEDs when the product lights up suddenly. This can happen

when power is applied, when the product receives a DMX signal, or when certain control menu items are

selected.

• To minimize the risk of eye irritation or injury, disconnect the fixture from power at all times when the

fixture is not in use, and provide well-lit conditions to reduce the pupil diameter of anyone working on or

near the fixture.

PROTECTION FROM INJURY

• Fasten the fixture securely to a fixed surface or structure when in use. The fixture is not portable when

installed.

• Do not lift or carry the fixture alone.

• Use two evenly spaced clamps to suspend the fixture from rigging structures. Do not use only one clamp.

• When clamping the fixture to a truss or other supporting structure at any other angle than with the yoke

hanging vertically downwards, use two half-coupler clamps. Do not use G-clamps, quick-trigger clamps or

any other type of clamp that does not completely encircle the supporting structure when fastened.

• When suspending the fixture, ensure that the supporting structure and all hardware used can hold at least

10 times the weight of all devices suspended from them.

• If the fixture is installed in a location where it may cause injury or damage if it falls, install as described in

this manual a secondary attachment such as a safety cable that is approved by an official body such as

TÜV as a safety attachment for the weight that it secures. The safety cable must comply with EN

60598-2-17 Section 17.6.6 and be capable of bearing a static suspended load that is ten times the weight

of the fixture and all installed accessories.

• Check that all external covers and rigging hardware are securely fastened.

• Block access below the work area and work from a stable platform whenever installing, servicing or

moving the fixture.

• Allow enough clearance around the head to ensure that it cannot collide with an object or another fixture

when it moves.

• Check that all external covers and rigging hardware are securely fastened.

6 MAC Quantum Wash Safety and Installation Manual

Introduction

Thank you for selecting the Martin™ MAC Quantum Wash™. This moving-head spotlight features:

• Fifty 15 Watt pre-mixed RGBW LEDs

• Full-spectrum RGBW color mixing and color temperature control

• ‘Color wheel’ effect with color presets

• Full-range dimming with four dimming curve options

• Electronic shutter effect with variable speed regular and random strobe

• Backlit graphic display and battery power (mains power not required for fixture setup)

• Auto-sensing switch-mode power supply.

For the latest firmware updates, documentation, and other information about this and all Martin Professional

products, please visit the Martin website at http://www.martin.com

Comments or suggestions regarding this document may be e-mailed to service@martin.dk or posted to:

Technical Documentation, Martin Professional, Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark.

Unpacking

The MAC Quantum Wash is packaged in either a

cardboard box or a flightcase that is designed to protect

the product during shipment.

This Safety and Installation Manual is included with the

product. The MAC Quantum Wash User Guide,

containing full details of setting up, controlling and

monitoring the fixture, is available for download from the

MAC Quantum Wash Product Support page on the

Martin website at www.martin.com. If you have any

difficulty locating this document, please contact your

Martin supplier for assistance.

Tilt lock

Release the tilt lock before applying power to the fixture.

See Figure 1. Release the tilt lock by pushing the lock in

towards the yoke (you can reapply the tilt lock by first

checking that the power is off and then pushing the lock

back in towards the yoke from the other side).

Packing

Important! Release the tilt lock and allow the fixture to cool before packing it in its flightcase.

The anti-shock material in the MAC Quantum Wash flightcase is designed to protect the head without the tilt

lock applied. Release the tilt lock when transporting the fixture in the flightcase. Leaving the tilt lock applied

may cause damage that is not covered by the product warranty.

Figure 1: Tilt lock

Physical installation 7

Physical installation

Warning! The MAC Quantum Wash has a powerful pan motor. The torque reaction when the head is

panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do

not apply power to the MAC Quantum Wash unless the base is securely fastened to a surface or to

rigging hardware.

Warning! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each

clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 90° clockwise.

Warning! When suspending the fixture above ground level, secure it against failure of primary

attachments by attaching a safety wire that is approved as a safety attachment for the weight of the

fixture to the attachment point in the base. Do not use the carrying handles for secondary

attachment.

Warning! When clamping the fixture to a truss or other structure at any other angle than with the

yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of

clamp that does not completely encircle the structure when fastened.

Warning! Position or shade the head so that the front lens will not be exposed to sunlight or another

strong light source from any angle – even for a few seconds. See Figure 2. The MAC Quantum

Wash’s lens can focus the sun's rays, creating a potential fire hazard and causing damage.

Important! Do not point the output from other lighting fixtures at the MAC Quantum Wash from a

distance of less than 3 m (10 ft.), as intense illumination can damage the display.

See Figure 2. Lenses can focus sunlight and

strong light, presenting a risk of fire and

damage to the fixture. Shield or shade the

head if necessary.

The MAC Quantum Wash can

be fastened to a surface such as

a stage or clamped to a truss in

any orientation. Clamps must be

half-coupler type (see Figure 4)

or equivalent type that fully

encircles the truss unless the

fixture is installed with the yoke

hanging vertically downwards,

in which case other clamp types

that are approved for the

supported weight may be used.

The mounting points in the base

allow omega brackets and

rigging clamps to be fastened

as shown in Figure 3.

Figure 2: Potential sunlight damage

Figure 3: Clamp bracket positions

8 MAC Quantum Wash Safety and Installation Manual

Clamping the fixture on a truss

1. Check that all rigging hardware is undamaged and can bear at least 10 times the weight of the fixture.

Check that the structure can bear at least 10 times the weight of all installed fixtures, clamps, cables,

auxiliary equipment, etc.

2. Bolt each rigging clamp securely to an omega bracket with an M12 bolt (minimum grade 8.8) and

self-locking nut.

3. See Figure 3 on page 7. Align the first

clamp and bracket with 2 mounting points

in the base, and engage both the clamp

bracket’s quarter-turn fasteners in

corresponding sockets in the base. See

Figure 4. Turn the levers on the

quarter-turn fasteners a full 90° clockwise

to lock. Repeat for the second clamp.

4. Block access under the work area. See

Figure 5. Note the position of the arrow

marked FRONT on the base of the fixture.

Working from a stable platform, hang the

fixture on the truss with the arrow marked

FRONT facing towards the area to be

illuminated. Tighten the rigging clamps.

5. See Figure 6. Install a safety cable that is

approved as a safety attachment for the

weight of the fixture by looping it through

the safety attachment point (arrowed) in

the bottom of the base and around a

secure anchoring point so that the safety

cable will catch the fixture if a primary

attachment fails.

6. Check that the tilt lock is released. Check

that there are no combustible materials

within 0.2 m (8 in.) or surfaces to be

illuminated within 2.0 m (6.6 ft.) of the

fixture, and that there are no flammable

materials nearby.

7. Check that there is no possibility of heads

or yokes colliding with other fixtures.

8. Check that other lighting fixtures cannot project light at the MAC Quantum Wash from a distance of less

than 3 m (10 ft.), as intense illumination can damage the MAC Quantum Wash’s display.

Figure 4: Martin rigging hardware

Half-coupler Omega bracket for

rigging clamp rigging clamp attachment

90°

Locking quarter-

turn fasteners

SAFETY CABLE

Figure 5: Front of fixture

SAFETY CABLE

Figure 6: Safety cable attachment point

AC power 9

AC power

Warning! For protection from electric shock, the fixture must be electrically connected to ground

(earth). The AC mains power supply must be fitted with a fuse or circuit breaker and ground-fault

(earth-fault) protection.

The MAC Quantum Wash features an auto-sensing switch-mode power supply that automatically adapts to

AC power at 120-240 V (nominal), 50/60 Hz.

Power input

Important! Connect the MAC Quantum Wash directly to AC power. Do not connect it to a dimmer

system; doing so may damage the fixture.

The MAC Quantum Wash requires a power input cable with a Neutrik PowerCon NAC3FCA cable connector

for AC mains power input. The cable must meet the requirements listed under “Protection from electric

shock” on page 4.

Martin™ can supply either a suitable 3 m (9.8 ft.) power cable with PowerCon input connector installed or

the PowerCon input connector without a cable (see “Accessories” on page 18).

Installing a power input connector on a power cable

To install a Neutrik PowerCon NAC3FCA input connector on a power

cable, see illustrations above and right:

1. Slide the bushing over the cable.

2. Slide the white chuck over cables with a diameter (Da) of 5 - 10 mm

(0.2 - 0.4 in.), or the black chuck over cables with a diameter of 10 -

15 mm (0.4 - 0.6 in.).

3. Prepare the end of the cable by stripping 20 mm (0.8 in.) of the

cable’s outer jacket.

4. Strip 8 mm (1/3 in.) of insulation from the end of each wire.

5. Use a small flathead screwdriver to fasten the wires into the

connector terminals in the insert as follows:

• live wire into the terminal marked L

• neutral wire into the terminal marked N

• ground (earth) wire into terminal marked .

6. Push the insert and chuck into the housing (note the raised key and

keyway to ensure correct orientation).

7. Fasten the bushing to the housing using a wrench to a torque of

2.5 Nm (1.8 lb.-ft).

Illustrations used by kind permission of Neutrik AG

Chuck BushingHousing Insert

Cable end

Terminals

10 MAC Quantum Wash Safety and Installation Manual

Connecting to an AC mains power source

The power cable can be hard-wired to a building installation circuit or fitted with a mains plug (cord cap) to

allow connection to local AC mains power outlets. If you install a mains plug, install a grounding-type

(earthed) plug, following the plug manufacturer’s instructions. Table 1 shows some possible mains power pin

identification schemes; if the pins are not clearly identified, or if you have any doubts about proper

installation, consult a qualified electrician.

Applying power

See Figure 7. To apply power to

the MAC Quantum Wash, check

that the tilt lock is released, that

the base is held securely, and that

personal safety will not be put at

risk when the fixture lights up and

moves, then set the power on/off

switch B to I(On).

Check that the mains power on/off

switch Bis set to O(Off) before

inserting or removing the power

input connector at the input

socket A, otherwise you may

cause arcing at connector

terminals that can damage them.

Wire Color (US) Wire Color (EU) Pin Symbol Screw (US)

black brown live Lyellow or brass

white blue neutral Nsilver

green yellow/green ground (earth) or green

Table 1: Cord cap (mains plug) connections

DMX

OUT

Disconnect from mains

before servicing.

Déconnecter du secteur

avant entretien.

MAINS

INPUT

MAINS

ON - OFF

AC MAINS SUPPLY

Brown = Live

Blue = Neutral

Yel/Green = Ground

(Earth)

Figure 7: Mains input socket and mains power on/off switch

A B

Autres manuels pour MAC Quantum Wash

Table des matières

Autres manuels Martin Luminaire

Martin

Martin CYCLO 04 DMX Manuel utilisateur

Martin

Martin MAC 301 Manuel utilisateur

Martin

Martin JEM ZR44 Hi-MASS Manuel utilisateur

Martin

Martin MAC Viper AirFX Manuel utilisateur

Martin

Martin MAC Viper Wash Manuel utilisateur

Martin

Martin MH 1 Profile Manuel utilisateur

Martin

Martin Exterior 1200 Wash Manuel utilisateur

Martin

Martin ERA 300 Profile Manuel utilisateur

Martin

Martin EFX500 Manuel utilisateur

Martin

Martin RUSH MH-2 Wash Manuel utilisateur

Martin

Martin MAC 401 Dual Manuel utilisateur

Martin

Martin MAC Viper Wash Manuel utilisateur

Martin

Martin smartMAC Manuel utilisateur

Martin

Martin MAC 2000 Wash XB Manuel utilisateur

Martin

Martin Cyclo 03 Directional Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Martin

Martin MAC 2000 Wash XB Manuel utilisateur

Martin

Martin MAC III PERFORMANCE Manuel utilisateur

Martin

Martin MAC 250 Beam Manuel utilisateur

Martin

Martin MAC 2000 Wash XB Manuel utilisateur

Martin

Martin Easypix Manuel utilisateur

Martin

Martin JEM ZR series Manuel utilisateur

Martin

Martin RoboColor Pro 400 Manuel utilisateur

Martin

Martin MAC Encore Performance Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur

ArtFox

ArtFox Beam 15R extreme Manuel utilisateur