Marco UNA FONT Manuel utilisateur
1
Instruction Manual
Machine P/N: 1000858, 1000859 UNA FONT
2
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Contents
1.FontBox Contents................................................................................................2
2.CounterCut-Out.................................................................................................2
3.Installation..........................................................................................................4
No Drip Tray...............................................................................................4
Drip Tray...................................................................................................5
ConnectingHoses......................................................................................6
4. Operating Font...................................................................................................7
5. Cleaning & Maintenance......................................................................................7
Font Box Contents
• 1B Unafont
• Vent Hosing 1860388
• 8mm Water Hose 1860386
• Instruction Manual
• SP9 Adaptor Kit
• 8mm - 1/4inch reducer 1400820
• Vent plug 1401482
• Buttons
•Flow straigntener 2100014
Counter Cut Out
• The 100mm /4” cut out is only required for the font with drip tray.
• The font without drip tray require the 32mm / 1 ¼” cut out only.
• Use a 32mm/ 1 ¼” & a 100mm /4” circular hole saw piece to make the holes.
3
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Counter Cut Out
4
Installation
32mm / 1 ¼”
1. No Drip Tray
130 - 500mm
130 - 500mm
50mm
Hosing should be trimmed to ensure
continuous drop from font to boiler
5
Installation
The drain outlet on the drip
tray should be plumbed to
waste.
32mm/ 1 ¼”
100mm/ 4”
2. Drip Tray (sold seperately p/n. 2300268)
130 - 500mm
130 - 500mm
50mm
Hosing should be trimmed to ensure
continuous drop from font to boiler
6
Hot Water
Power
Vent
Connecting Hoses
Vent
Hot Water
SP9 Boiler
Hot Cold / Sparkling
SP9 Boiler Connection
Power
Vent plug
8mm - 1/4inch
reducer
Cold Water
7
Power
Vent plug
8mm - 1/4inch
reducer
Cold Water
Hot / Cold Ready to drink
If using urn use
hard tubing
Power
font to control box
Concentrate shot
hot or cold source
to coffee source
Power
font to control box
Concentrate source
(soft tubing for BIB
Hard tubing for urn)
UNA FONT - Connecting Hoses
8mm - 1/4inch
reducer piece
8mm - 1/4inch
reducer piece
5/16 to 3/8
barbed
connector
8
Operating Font
Cleaning & Maintenance
RISK OF SCALDING
Turn off the boiler before cleaning to
prevent accidental triggering of a
dispense.
Beware of accidentally operating the font –
especially when cleaning around the push
buttons.
The exterior of this font may be cleaned
with a damp cloth and a light detergent.
Twist off and wash out flow straightener.
Do not use abrasive cloths or creams, as
this will spoil the finish of the font.
1. Push & Hold 2. Push & Release
85°
100
9
Marco Beverage Systems Limited.
63d Heather Road,
Sandyford Industrial Estate,
Dublin 18
t: +353 (0)1 295 2674
f: +353 (0)1 295 3715
e: sales@marco.ie
www.marcobeveragesystems.com
NSF/ANSI 4
E337347
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Marco Système d'eau
Manuels Système d'eau populaires d'autres marques
Spirotech
Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur
Culligan
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur
A.O. Smith
A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur
Microline
Microline T.F.C.-4 Manuel
Eureka Forbes
Eureka Forbes Aquaguard Select Manuel utilisateur
Cetetherm
Cetetherm AquaEfficiency Manuel utilisateur
